Instructions / Assembly

ManualsBrandsAmerican Standard ManualsBathFluent 8 in. Widespread Bathroom Faucet with Speed Connect Drain and Color Indicator in Polished Chrome

M965622

SPOUT BASE

Turn off hot and cold water

supplies before beginning.

CAUTION

Insert (1) CABLE CONNECTOR (2) and HOSE (3) through center hole,

making sure SEAL WASHER (4) is properly seated in spout base.

Assemble RUBBER WASHER (5), LOCKNUT (6) and thread LOCKNUT (6)

onto SHANK (7) from underside of sink or mounting surface.

Align and center SPOUT (1). Tighten LOCKNUT (6).

7186.801

7186.811

Certiﬁed to comply with ANSI A112.18.1

Installation

Instructions

Wide Spread Lavatory Faucet

with Speed Connect® Drain

INSTALL SPOUT

INSTALL VALVE BODIES

Remove LOCKNUT (8) and RUBBER WASHER (9) from

SIDE VALVE SHANKS (10).

Insert Hot and Cold SIDE VALVE HOSES (11), FLEXIBLE

SUPPLIES (11a) into mounting holes making sure the SEAL

WASHERS (12) are properly seated in each HANDLE BASE (13).

Assemble RUBBER WASHER (9) and thread

LOCKNUT (8) onto each SIDE VALVE

SHANK (10) from underside of sink

or mounting surface.

Align and center SIDE VALVES.

Tighten LOCKNUTS (8).

Adjustable Wrench Flat Head Screwdriver Slip Jaw Pliers

Recommended tools

Tubing Cutter

Fig. A.

Fig. B.

Congratulations on purchasing your American Standard

faucet with Speed Connect drain, a feature found only on

American Standard faucets.

*Your new American Standard faucet is designed to work only with the Speed Connect drain.

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

Speed Connect® Drain*

• Fewer parts, installs in less time

• Never needs adjustment

• Guaranteed to seal properly the rst time, every time.

11 Blue Stripe (C0LD)

11 Red Stripe (HOT)

FLUENT™

11a

Summary of content (7 pages)

PAGE 1
FLUENT™ W ide Spread Lavatory Faucet with Speed Connect® Drain Installation Instructions 7186.801 7186.811 Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard faucets. Speed Connect® Drain* • Fewer parts, installs in less time • Never needs adjustment • Guaranteed to seal properly the first time, every time. Certified to comply with ANSI A112.18.
PAGE 2
POP-UP DRAIN Fig. B. Fig. A. Remove CLEAR PLASTIC COVER (1). 1 Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). 3 DRAIN BODY Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 2 3 REMOVE FLANGE 4 Fig. A. Fig. B. 1 Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B.
PAGE 3
7 ATTACH CABLE CONNECTOR Fig. A. Fig. B. Thread CABLE CONNECTOR (1) clockwise onto CABLE ATTACHMENT POINT (2) and hand tighten. Fig. A. 1 Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. 2 8 1-1/4” O.D. CHECK OPERATION OF POP-UP 1 Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. Note: If STOPPER (2) does not open and close properly, refer to the “troubleshooting section” of these instructions.
PAGE 4
10 TEST INSTALLED FITTING With HANDLES (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. 1 5 Remove AERATOR (3). Operate both HANDLES (1) to flush water lines thoroughly. 1 Replace AERATOR (3). 11 3 CHECK DRAIN CONNECTIONS Operate POP-UP KNOB (5) and fill Sink with water. Check that DRAIN STOPPER (4) makes a good seal and retains water in Sink. If STOPPER (4) does not seal properly, please refer to “Troubleshooting Guide” in these instructions.
PAGE 5
Speed Connect® Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
PAGE 6
STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front.
PAGE 7
FLUENT™ Wide Spread Lavatory Faucet with Speed Connect® Drain MODEL NUMBER M964919-YYY0A LEVER HANDLE (LEFT) 7186.801 7186.