Installation Guide

ManualsBrandsAmerican Standard ManualsBathTropic Toilet Tank Cover in Linen

1

2

3

7301450-100 Rev. A

Product names listed herein are trademarks of AS America, Inc.

© AS America, Inc. 2009

RECOMMENDED TOOLS AND MATERIALS

Putty Knife

Closet Bolts

Regular Screwdriver

Wax Ring/Gasket

Adjustable Wrench

Flexible Supply Tube

Sealant

Hacksaw

Carpenters Level

Tape Measure

ROUGHING-IN DIMENSIONS:

REMOVE OLD TOILET

1

2

a. Close toilet supply valve and flush tank

completely. Towel or sponge remaining

water from tank and bowl.

b. Disconnect and remove supply line.

NOTE: If replacing valve, first shut off main

water supply!

c. Remove old mounting hardware, remove

toilet and plug floor waste opening to

prevent escaping sewer gases.

d. Remove closet bolts from flange and

clean away old wax, putty, etc. from

base area.

NOTE: Mounting surface must be clean

and level before new toilet is installed!

SAVE FOR FUTURE USE

BOULEVARD 1.6 gpf/6 Lpf One-Piece Toilet

BOULEVARD 1.28 gpf/4.8 Lpf One-Piece Toilet

Model 2891-Elongated Right Height™ with Seat

TROPIC 1.6 gpf/6 Lpf One-Piece Toilet

TROPIC 1.28 gpf/4.8 Lpf One-Piece Toilet

Model 2786-Elongated Right Height™ with Seat

TOWN SQUARE 1.6 gpf/6 Lpf One-Piece Toilet

TOWN SQUARE 1.28 gpf/4.8 Lpf One-Piece Toilet

Model 2847-Elongated Right Height™ with Seat

Model 2786-TROPIC 1.6 gpf/6 Lpf - TROPIC 1.28 gpf/4.8 Lpf

Model 2847-TOWN SQUARE 1.6 gpf/6 Lpf - TOWN SQUARE 1.28 gpf/4.8 Lpf

Model 2891-BOULEVARD 1.6 gpf/6 Lpf - BOULEVARD 1.28 gpf/4.8 Lpf

CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

NOTE: Pictures may not exactly define contour of china and components.

Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read

these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.

!

INSTALLATION INSTRUCTIONS

Certiﬁed by

IAPMO R&T

NOTE: Distance from wall to closet flange centerline must be as listed below:

C/L OF SEAT POST

HOLES 5-1/2"

(140mm) CENTERS

29-3/4"

(756 mm)

8-1/8"

(206 mm)

3/4"

(19 mm)

18-1/2"

(470 mm)

3-1/2"

(88 mm)

8-1/2"

(217 mm)

13-1/2"

(345 mm)

14"

(354 mm)

16-3/4"

(424 mm)

30-1/2"

(778 mm)

16-1/2"

(419 mm)

12"

(305 mm)

C/L OF OUTLET AND

TOILET MTG BOLTS

FINISHED WALL

IMPORTANT: Water supply on the wall is required at 3-3/4" or 9" from centerline of the toilet (see rough-in).

First suggested position is hidden behind the toilet. The geometry of the toilet gives space for this installation.

The second suggested position is next to the toilet. Between these two positions, the space for the supply

between wall and toilet is limited to 3-1/4". In this case, check your supply and hose dimensions.

IMPORTANT: Water supply on the wall is required at 3-3/4" or 9" from centerline of the toilet (see rough-in).

First suggested position is hidden behind the toilet. The geometry of the toilet gives space for this installation.

The second suggested position is next to the toilet. Between these two positions, the space for the supply

between wall and toilet is limited to 3-1/4". In this case, check your supply and hose dimensions.

IMPORTANT: Water supply on the wall is required at 3-3/4" or 9" from centerline of the toilet (see rough-in).

First suggested position is hidden behind the toilet. The geometry of the toilet gives space for this installation.

The second suggested position is next to the toilet. Between these two positions, the space for the supply

between wall and toilet is limited to 3-1/4". In this case, check your supply and hose dimensions.

FINISHED

FLOOR

2-7/8"

(74mm)

5-1/2"

(140mm)

SUPPLY AS

REQUIRED

(position 2)

SUPPLY AS

REQUIRED

(position 1)

6"

(152mm)

3-3/4"

(95mm)

9"

(229mm)

14"

(355 mm)

29-3/4"

(756 mm)

7-1/2"

(192 mm)

3/4"

(19 mm)

18-1/2"

(470 mm)

16-1/2"

(419 mm)

14-1/2"

(368 mm)

30-1/2"

(778 mm)

13-1/2"

(345 mm)

14-1/4"

(364 mm)

8-1/2"

(217 mm)

12"

(305 mm)

C/L OF SEAT POST

HOLES 5-1/2"

(140mm) CENTERS

FINISHED WALL

3-3/8"

(86mm)

3-1/4"

(83mm)

SUPPLY

AS

REQUIRED

(position 1 or

position 2)

6"

(152mm)

5-1/2"

(140mm)

3-3/4"

(95mm)

9"

(229mm)

14"

(350 mm)

FINISHED

FLOOR

12" ( mm)305

29-7/8"

(758 mm)

6-7/8"

(175 mm)

7/8"

(22 mm)

18-1/2"

(470 mm)

3-1/2"

(88 mm)

2-3/4"

(69 mm)

8-1/2"

(217 mm)

14-5/8"

(373 mm)

14-5/8"

(373 mm)

16-1/2"

(419 mm)

15-1/8"

(384 mm)

30-3/4"

(780 mm)

12"

(305 mm)

FINISHED

FLOOR

C/L OF SEAT POST

HOLES 5-1/2"

(140mm) CENTERS

SUPPLY

AS

REQUIRED

(position 1 or

position 2)

6"

(152mm)

5-1/2"

(140mm)

3-3/4"

(95mm)

9"

(229mm)

14"

(356 mm)

OR

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS BOULEVARD 1.6 gpf/6 Lpf One-Piece Toilet BOULEVARD 1.28 gpf/4.8 Lpf One-Piece Toilet Model 2891-Elongated Right Height™ with Seat TROPIC 1.6 gpf/6 Lpf One-Piece Toilet TROPIC 1.28 gpf/4.8 Lpf One-Piece Toilet Model 2786-Elongated Right Height™ with Seat Certified by IAPMO R&T TOWN SQUARE 1.6 gpf/6 Lpf One-Piece Toilet TOWN SQUARE 1.28 gpf/4.
PAGE 2
4 3 5 CLOSET FLANGE NUT OPENING A TAPERED WASHER CLOSET BOLTS SEALANT INSTALL WAX SEAL Invert toilet on floor (cushion to prevent damage), and install wax ring evenly around waste flange (horn), with tapered end of ring facing toilet. Apply a thin bead of sealant around toilet base. INSTALL CLOSET BOLTS Install closet bolts in flange channel, turn 90°, and slide into place 6" (152mm) apart and parallel to wall. 6 a. FLANGE CLOSET BOLT WAX RING POSITION TOILET ON FLANGE a.
PAGE 3
9 10 ADJUSTMENTS ARM TOP NIPPLE REFILL TUBE a. Adjust water level. Water level should be adjusted to level indicated on tank by adjusting float cup. TANK LEVER CRITICAL LEVEL MARK ("C.L.") MUST BE 1" ABOVE OVERFLOW PIPE Fig. 9A See Step 10 for water level adjustment method. "S" CLIP FLOAT CUP b. If bowl fails to siphon, an adjustment may be required with the lift chain. Simply remove the bead chain from the retainment clip (see Fig. 9A) and take up slack on the chain, and reinsert on lift rod.
PAGE 4
REPAIR PARTS LIST NOTE: "XXX" represents color options. Specify when ordering. BOULEVARD COMPONENT 735148.XXX0A 735147.XXX0A 735150.XXX0A 5218.110.XXX 5216.110.XXX 5214.110.XXX 7381073-XXX0A 730835-XXX0A 7381064-XXX0A 7381097-XXX0A 7381105-XXX0A 738565-439.0070A 738942-100.0070A 738920-100.0070A 738565-438.0070A 738942-102.0070A 7381043-400.