Installation Guide

ManualsBrandsAmerican Standard Manuals8 inch Widespread Sink Faucets8 in. Widespread 2-Handle Mid-Arc Bathroom Faucet in Oil Rubbed Bronze with Speed Connect Drain and Cross Handles

M 9 6 5 015 R E V. 1.7

Certiﬁed to comply with ANSI A112.18.1

Adjustable Wrench Screwdriver Channel Locks

Recommended tools

Tubing Cutter

SLOT

Turn off hot and cold water

supplies before beginning.

CAUTION

Insert SPOUT (1) and CABLE CONNECTOR (12) through center hole, making sure

the SEAL WASHER (3) is properly seated in the SPOUT ESCUTCHEON (2).

Assemble RUBBER WASHER (4), BRASS WASHER (5) and LOCKNUT (6) onto SPOUT

SHANK (7) from under side of sink . Make sure SPOUT (1) is centered in the mounting

hole and the slot in the BRASS WASHER (5) faces toward the rear of the sink.

Tighten LOCKNUT (6) ﬁrmly. Fig. A.

INSTALL SPOUT

INSTALL VALVE BODY

Fig. A.

MOUNTING

SURFACE

Hand tighten LOCKNUT (11) to secure VALVE BODY (8).

Repeat above steps for opposite VALVE BODY (8A).

Install LOCKNUT (11) onto VALVE BODY (8).

From under side of mounting surface, install VALVE BODY (8) through valve

mounting holes. Threads of VALVE BODY (8) should extent at least 5/16

of a inch above mounting surface top. Fig. B. Thread ADAPTER (10)

onto VALVE BODY (8) until snug against internal stop. If necessary, adjust

LOCKNUT (11).

Place RUBBER RING (9) into ADAPTER (10).

5/16'' MIN.

Fig. B.

7420.801

7420.821

Series

7415.801

7415.821

Series

Installation

Instructions

PORTSMOUTH™

Spread Lavatory Faucet

with Speed Connect™ Drain

Congratulations on purchasing your

American Standard faucet with

Speed Connect drain, a feature found

onlyon American Standard faucets.

*Your new American Standard faucet is designed to work only with the Speed Connect drain.

Heplful tips for removing your current drain can be found in the Troubleshooting section of these instructions.

To ensure that your installation proceeds smoothly-please read these instructions carefully

before you begin.

7420

7415

Speed Connect Drain*

• Fewer parts, installs in less time

• Never needs adjustment

• Guaranteed to seal properly the ﬁrst time, every time.

Summary of content (8 pages)

PAGE 1
Installation Instructions PORTSMOUTH™ 7420.801 Spread Lavatory Faucet 7420.821 with Speed Connect™ Drain Series Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found 7415.801 onlyon American Standard faucets. 7415.821 Speed Connect Drain* Series • Fewer parts, installs in less time 74 2 0 74 15 • Never needs adjustment • Guaranteed to seal properly the first time, every time. Certified to comply with ANSI A112.18.1 M 9 6 5 015 R E V. 1.
PAGE 2
POP-UP DRAIN Fig. A. Fig. B. Remove CLEAR PLASTIC COVER (1). 1 Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). 3 DRAIN BODY Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 2 3 REMOVE FLANGE 4 Fig. A. Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Fig. B. 1 Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B.
PAGE 3
7 ATTACH CABLE CONNECTOR Fig. A. Fig. B. Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. 1 Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. 2 8 1-1/4” O.D. CHECK OPERATION OF POP-UP 1 Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions.
PAGE 4
10 INSTALL HANDLES Push ADAPTER (1) on VALVE STEM (2), so that the hole of the ADAPTER (1) with the spline is facing up. Fig. A. Tighten STEM SCREW (3) to secure ADAPTER (1). Find correct position of LEVER HANDLE ASSEMBLY (4) by adjusting male teeth on ADAPTER (1) to female teeth in HANDLE (4). Thread LEVER HANDLE ASSEMBLY (4) onto DECK ADAPTER (5) until snug against mounting surface. THREAD ON TO DECK ADAPTER 4 SPLINE END UP 1 3 2 Fig. A.
PAGE 5
Speed Connect™ Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
PAGE 6
STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front.
PAGE 7
PORTSMOUTH™ Spread Lavatory Faucet with Speed Connect™ Drain MODEL NUMBER M950211-YYY0A LIFT ROD & KNOB 7420.801 7420.821 Series M962946-YYY0A CROSS HANDLE M962590-YYY0A SPOUT KIT M962937-YYY0A HANDLE M962592-0070A DECK ADAPTER KIT M922881-YYY0A AERATOR M911741-0070A SEAL Replace the "YYY" with appropriate finish code CHROME BLACKENED BRONZE OIL RUBBED BRONZE SATIN NICKEL 002 068 224 295 M961733-0070A SPOUT MTG.
PAGE 8
PORTSMOUTH™ Spread Lavatory Faucet with Speed Connect™ Drain MODEL NUMBER M962946-YYY0A CROSS HANDLE 7415.801 7415.821 Series M962455-YYY0A LIFT ROD & KNOB M962052-YYY0A SPOUT KIT M962947-YYY0A HANDLE M922881-YYY0A AERATOR M962453-YYY0A SEAL & ESCUTCHEON M962592-0070A DECK ADAPTER KIT M961733-0070A SPOUT MTG.