Installation Guide

ManualsBrandsAmerican Standard ManualsBathPortsmouth Monoblock Single Hole Single Handle Mid Arc Bathroom Faucet with Speed Connect Drain in Oil Rubbed Bronze

7415.101

7420.101

Certiﬁed to comply with ANSI A112.18.1

Installation

Instructions

MONOBLOCK LAVATORY

FAUCET with

Speed Connect™ Drain

Adjustable Wrench Screwdriver Channel Locks

Recommended tools

7420.101

7415.101

Series

PORTSMOUTH

To ensure that your installation proceeds smoothly-please read these instructions carefully

before you begin.

Congratulations on purchasing your American Standard

faucet with Speed Connect drain, a feature found only

on American Standard faucets.

*Your new American Standard faucet is designed to work only with the Speed Connect drain.

Speed Connect Drain*

• Fewer parts, installs in less time

• Never needs adjustment

• Guaranteed to seal properly the ﬁrst time, every time.

COLLAR ON

MOUNTING NUT

INSTALL FAUCET

7420.101 & 7415.101

Turn off hot and cold water

supplies before beginning.

CAUTION

GROOVE

(FAUCET

BASE)

MOUNTING SURFACE

Installation less ESCUTCHEON PLATE:

Seat SEAL (1) into under side of FAUCET BASE (2).

Feed FAUCET SUPPLIES (3), MOUNTING STUD (4) and DRAIN

CABLE ASSEMBLY (8) through the mounting hole of lavatory or

mounting surface. Fig. B.

From below, push GASKET (7) and RETAINING WASHER (5) onto

MOUNTING STUD (4). Secure Faucet with MOUNTING NUT (6),

pulling faucet to front of sink, so SUPPLIES (3) rests against

mounting hole. Before ﬁnal tightening, make sure collar on

MOUNTING NUT (6) is seated into RETAINING WASHER (5).

Fig. C .

Adjust Faucet so that it is centered. Tighten MOUNTING NUT (6)

to complete faucet mounting.

Fig. C.

Fig. B.

Fig. A.

M965016 REV. 2.2 (6/15)

Installation with ESCUTCHEON PLATE (optional) must be purchased separately:

Apply a light bead of plumbers putty to underside of ESCUTCHEON PLATE (8)

if mounting surface is uneven. Place ESCUTCHEON PLATE (8) onto sink or

mounting surface.

Feed FAUCET SUPPLIES (3), MOUNTING STUD (4) and

DRAIN CABLE ASSEMBLY (8) through

ESCUTCHEON PLATE (8) and

mounting hole of lavatory or mounting surface.

Fig. A.

PUTTY

IF REQUIRED

Summary of content (8 pages)

PAGE 1
Installation Instructions 7420.101 PORTSMOUTH® 7415.101 MONOBLOCK LAVATORY Series FAUCET with Speed Connect™ Drain 7415.101 Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard faucets. 7420.101 Speed Connect Drain* • Fewer parts, installs in less time • Never needs adjustment • Guaranteed to seal properly the first time, every time. Certified to comply with ANSI A112.18.1 M965016 REV. 2.
PAGE 2
POP-UP DRAIN Fig. A. Fig. B. Remove CLEAR PLASTIC COVER (1). 1 Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). 3 DRAIN BODY Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 2 3 REMOVE FLANGE 4 Fig. A. Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Fig. B. 1 Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B.
PAGE 3
7 ATTACH CABLE CONNECTOR Fig. A. Fig. B. Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. 1 Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. 2 1-1/4” O.D. 8 CHECK OPERATION OF POP-UP Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. 1 Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions.
PAGE 4
10 ON TEST INSTALLED FITTING OFF 1 With HANDLE (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. COLD HOT 4 Remove AERATOR (3). Operate HANDLE (1) to flush water lines thoroughly. Replace AERATOR (3). 3 CHECK DRAIN CONNECTIONS Operate POP-UP KNOB (4) and fill lavatory with water. Check that DRAIN STOPPER (5) makes a good seal and retains water in SINK. If DRAIN STOPPER (5) does not seal properly, please refer to Troubleshooting section in these instructions.
PAGE 5
Speed Connect™ Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
PAGE 6
STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front.
PAGE 7
PORTSMOUTH ® M917161-0070A SET SCREW Momoblock Lavatory Faucet with Speed Connect™ Drain M962951-YYY0A HANDLE KIT MODEL NUMBERS 7415.
PAGE 8
PORTSMOUTH ® Momoblock Lavatory Faucet with Speed Connect™ Drain MODEL NUMBER 7420.