Installation Guide

ManualsBrandsAmerican Standard ManualsBathTown Square S 2-Handle Wall Mount Bathroom Faucet in Legacy Bronze

- 1 -

Product names listed herein are trademarks of AS America, Inc.

Thank you for selecting American Standard...

the benchmark of ﬁne quality for over 140 years.

To ensure that your installation proceeds smoothly-please read

these instructions carefully before you begin.

RECOMMENDED TOOLS

ROUGH-IN DIMENSIONS

INSTALL VALVE BODY

Town Square

Wall Mount Faucet

INSTALLATION

INSTRUCTIONS

7455451

Certied to comply with ANSI A112.18.1M

CAUTION

Turn off hot and cold water

supplies before begining.

M965962 (5/18)

• Determine where the nished wall location will be. This measurement

is very important! NOTE: The rough-in measurement from the nished

wall is; 2" minimum and 3" maximum. This is a 1" tolerance.

See rough-in illustration above.

• Secure FAUCET BODY (1) to cross brace of wall structure

at required height using two wood screws.

• Connect HOT water supply to left VALVE inlet and COLD

water supply to right VALVE inlet. Use pipe sealant or

Teon tape forall threaded connections. For sweat connections,

do not makesweat connections directly to valve body.

Damage to seals and and valve cartridge may occur.

• Turn valves to off position. Turn hot and cold supplies on and

check tting connections for leaks .

• Complete wall construction.

Adjustable Wrench

Flat Blade Screwdriver

Channel LocksPipe WrenchTeon Tape

Tubing Cutter

Plumbers' Putty or

Caulking

FINISHED

WALL

2-1/4" D.

(57 mm)

8-7/8"

(225 mm)

(25 mm)

2" MIN.

(51 mm)

3" MAX.

(76 mm) MAX.

WOOD SCREWS

HOT

COLD

CROSS BRACE

WALL STUDS

16"

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS 7455451 Town Square® S Wall Mount Faucet Thank you for selecting American Standard... the benchmark of fine quality for over 140 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1M RECOMMENDED TOOLS Flat Blade Screwdriver Teflon Tape Plumbers' Putty or Caulking ROUGH-IN DIMENSIONS Pipe Wrench Channel Locks 2" MIN. (51 mm) Tubing Cutter Adjustable Wrench 3" MAX.
PAGE 2
INSTALL DRAIN FROM BELOW FIXTURE • Remove PLASTER GUARDS (1) from valve bodies and SPOUT NIPPLE (3). • Inspect that SPOUT NIPPLE O-RING (2) is seated in groove of SPOUT NIPPLE (3). • T hread SPOUT MOUNT (4) onto SPOUT NIPPLE (3). Align groove on SPOUT MOUNT (4) with face of finished wall. See Figure A. 3 /8 1-5 MIN • Insert SPOUT (7) upside down with the aerator facing up. Tighten the SPOUT SET SCREW (8) with the 3 mm hex wrench (9) supplied.
PAGE 3
5 SERVICE CAUTION Turn off hot and cold water supplies before begining. • To change direction of handle rotation, proceed as follows: 4 — Turn valve to OFF position. — Thread counter-clock wise HANDLE BASE (1) to remove HANDLE ASSEMBLY (2) from VALVE HOUSING (3). 3 90˚ TO REMOVE HANDLE — Thread counter-clock wise VALVE HOUSING (3) to remove. — Use a flat blade screw driver to remove SPRING CLIP (4). 5 — Lift STOP WASHER (5), turn 90˚ and replace. — Replace SPRING CLIP (4).
PAGE 4
Town Square® S Wall Mount Faucet MODEL NUMBER 7455451 A912699-0070A SEAL 994053-0070A CARTRIDGE 617852-0070A ADAPTER A918305-0070A HANDLE SCREW M923840-0070A AERATOR (1.2 GPM) 621423-0070A VALVE HOUSING M970517-YYY0A HANDLE KIT M953455-YYY0A DRAIN COMPLETE Replace the “YYY” with appropriate finish code POLISHED CHROME 002 POLISHED NICKEL 013 LEGACY BRONZE 278 SATIN NICKEL 295 HOT LINE FOR HELP For toll-free information and answers to your questions, call: 1 (800) 442-1902 Mon. - Fri. 8:00 a.