Replacement Part List

CENTERSET LAVATORY FAUCETS

WITH GOOSENECK SPOUT

Installation

Instructions

7500 Series

7501 Series

7502 Series

7545 Series

Thank you for selecting American-Standard...

the benchmark of ﬁne quality for over 100 years.

To ensure that your installation proceeds smoothly--

please read these instructions carefully before you begin.

Certiﬁed to comply with ANSI A112.18.1M

60185 Rev. 1.7 (11/15)

Apply a bead of PUTTY around underside of DRAIN PLUG FLANGE (1). Insert DRAIN PLUG (2)

into SINK drain hole.

Hold DRAIN PLUG (2) to prevent turning and assemble GASKET (3), WASHER (4) and LOCKNUT (5)

from underneath sink.

Insert threaded end of TAILPIECE (6) into lower end of DRAIN PLUG (2). Connect other end to trap.

GRID DRAIN ASSEMBLY (Model 7502 only)

Asesemble GASKET (1) to SHANKS (2) and insert FAUCET SHANKS

through holes of SINK.

Assemble LOCKNUTS (3) from underside of SINK. Align BODY as far forward as possible

and secure position by tightening LOCKNUTS (3).

Connect the HOT water supply to the left SHANK and the COLD water supply to the right

SHANK using sealant, appropriate connectors, and COUPLING NUTS (4).

Unscrew SPOUT NUT (5) and remove SPOUT (6).

To change spout to a swivel spout: (7500, & 7502)

Take SPOUT CLIP (7) off SPOUT (6) and remove RUBBER RING (8).

Replace RUBBER RING (8) with seperate PLASTIC RING (9)

packed with faucet.

Put SPOUT CLIP (7) on SPOUT.

Reassemble SPOUT (6) to BODY.

BODY

SINK

HOT

COLD

1/2" O.D. SLIP

Turn off water at

main supply.

CAUTION

PUTTY

SINK

PAGE 1
Installation Instructions CENTERSET LAVATORY FAUCETS WITH GOOSENECK SPOUT 7500 7501 7502 7545 Series Series Series Series Thank you for selecting American-Standard... the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. 1 CAUTION Certified to comply with ANSI A112.18.1M 60185 Rev. 1.7 (11/15) Turn off water at main supply.
PAGE 2
3 TEST INSTALLED FAUCET Remove AERATOR. Operate LIFT ROD and check DRAIN for leaks. With handle in OFF position, turn on water supplies and check all connections for leaks. Turn handles into OFF position and replace AERATOR. Operate both handles to flush water lines thoroughly. Check spout mounting and hose connections for leaks. 4 SERVICE To change direction of handle rotation, proceed as follows: Turn valve to OFF position. Remove HANDLE and BONNET NUT. Remove SPRING CLIP.
PAGE 3
7500 7501 7502 7545 M919646-0020A SPOUT M922858-0020A VR AERATOR, 0.35gpm 051322-0020A VANDAL PROOF SCREW 066114 -0020A VR AERATOR, 0.5gpm GRID DRAIN 000690-0020A HANDLE SCREW 051211-0070A INDEX KIT 051214-0070A SWIVEL/FIXED SPOUT RINGS 015025-YYY0A DRAIN COMPLETE 070532-0040A TAILPIECE Series Series Series Series M964478-0020A 6" WRIST BLADE HANDLE KIT (7400.160) 051217-0020A 4" WRIST BLADE HANDLE KIT M923208-0070A FLOW RESTRICTOR (7500.180, 7500.188 7500.