Installation Guide

ManualsBrandsAmerican Standard ManualsBathNextGen Selectronic AC Powered Single Hole Touchless Bathroom Faucet with Above Deck Mixing 0.35 GPM in Chrome

M965754 Rev. 2.1 (3/21)

Installation Instructions

Certied to comply with ASME A112.18.1

NOTE TO INSTALLER: Please give this manual to the customer after installation.

To learn more about American Standard Selectronic

Products visit our website at: www.americanstandard-us.

com or e-mail us at: sensor@lixil.com

For Parts, Service, Warranty or other Assistance,

please call (844) CRT-TEAM / (844) 278-8326 (In Canada: 1-800-387-0369)

(In Toronto Area only: 1-905-306-1093)

NextGen Selectronic

Integrated Faucet with Optional Above-Deck

Mixing & SmarTherm

Temperature Limiter

MODEL NUMBERS

7755.1xx 775B.1xx

7755.2xx 775B.2xx

7755.3xx 775B.3xx

CAUTION: Use only American Standard supplied

transformers and cable sets. Using non-AS supplied

cables, or cutting, splicing or modifying any

components will void the warranty.

Product No’.s & Options 2

Speciﬁcations 3

Faucet Installation 3

Electrical Installation 4-5

FAQ’s / Troubleshooting 9

Parts 10

Start-up / Maintenance 6-8

Summary of content (10 pages)

PAGE 1
I nstallation Inst ru c t i on s NextGen Selectronic® Integrated Faucet with Optional Above-Deck Mixing & SmarTherm® Temperature Limiter MODEL NUMBERS 7755.1xx 775B.1xx 7755.2xx 775B.2xx 7755.3xx 775B.3xx CAUTION: Use only American Standard supplied transformers and cable sets. Using non-AS supplied cables, or cutting, splicing or modifying any components will void the warranty. Product No’.
PAGE 2
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. UNPACKING All American Standard Products Are Water Tested At Our Factory. Some Residual Water May Remain In The Valve During Shipping. Remove the fitting and loose items from the carton. The illustration below shows all the fittings and loose items after they have been removed from the carton.
PAGE 3
Roughing-in Dimensions Note: All plumbing and electrical wiring must be installed in accordance with applicable codes, regulations and standards. 174 mm (6-7/8") CAUTION: Use only American Standard supplied transformers and cable sets. Using non-AS supplied cables, or cutting, splicing or modifying any components will void the warranty.
PAGE 4
Fig. 1 ELECTRICAL INSTALLATION 4 Product Page 3 PWRX Power Kit (PK00.WRK) 4 Plug-In AC Power Kit (PK00.PAC) 5 Hard-Wired AC Power Kit (PK00.HAC) 5 Multi-AC Power Kit (PK00.MAC) 5 4 3 2 1 Important: All 7755 faucets with CR-P2 battery come with electrical connections preaseambled at the factory. No further action necessary. A PWRX 10 YEAR BATTERY SYSTEM; Fig. 1 BRACKET INSTALLATION PWRK™ VERSION; 1. Connect PWRX BATTERY PACK (1) to SENSOR CABLE (2). 2.
PAGE 5
B AC VERSIONS (HARD-WIRED / Fig. 2 PLUG-IN POWER SUPPLY); Fig. 2 1 Important: Turn off power to outlet or electrical box. FOR PLUG-IN VERSION; 1. Connect PLUG-IN AC POWER SUPPLY (2) to one end of the SINGLE AC ADAPTER (6). 2. Connect SENSOR CABLE (4) to the other end of the SINGLE AC ADAPTER (6). 3. Connect PLUG-IN AC POWER SUPPLY (2) to wall outlet. 10' EXTENSION 7 AC-DC CONVERTER 5 4 1 FOR HARD-WIRED VERSION; 1. Connect HARD-WIRED AC TRANSFORMER (3) to AC-DC CONVERTER (7). 2.
PAGE 6
D MAKE WATER SUPPLY IMPORTANT: Do not use sealent on threads HOT 4 Fig. 45 Fig. CONNECTIONS; Fig. 4 Optional Mixing Valve (Sold Separately) 1 SELECTRONIC™ Thermostatic Mixing Valve 605XTMV TEMPERED WATER SUPPLY 3 (3) INLINE FILTER Certified to comply with ASME A112.18.1M © 2005 American Standard Specifications 1 Installation 2 Adjust Temperature 3 Service 3 Replacement Parts 4 5 M968808 COLD NOTE TO INSTALLER: Please give this manual to the customer after installation.
PAGE 7
MAINTENANCE 15 2 16 B REPLACE BATTERY; Fig. 5, 6 17 1. Remove COVER SCREW (1) and lift COVER (15) off. 12 1 2. Disconnect SENSOR CABLES (6) and (7) from the BATTERY and SOLENOID VALVE. (Fig. 6) 3. Push BATTERY (17) forward and Pull it out. (Fig. 5) 4 4. Replace the new battery with the same placement. (Insert terminal side first) C 14 CHANGE SENSOR RANGE; 9 Fig. 5, 6 1. Remove the COVER SCREW (1). 2. Remove the COVER (15). 3.
PAGE 8
Fig. 12 E A DJUST OR REPLACE MAXIMUM OUTLET TEMPERATURE; Fig. 8 1. With the COVER off, the installer can reduce the maximum mixed water temperature by turning the THERMO VALVE (4) clockwise with a screwdriver. 6 4 2. Remove SCREW (6) and unthread THERMO VALVE (4). Replace with new THERMO VALVE (4). WARNING • Do not turn the THERMO VALVE (4) More than 1 turn. • The maximum mixed water temperature can not be increased due to ASSE 1070 requirements. F GENERAL CLEANING Fig. 8 1.
PAGE 9
TROUBLESHOOTING FLOW CHARTS UNIT DOES NOT FUNCTION ARE EXTERNAL SUPPLY STOPS OPEN? NO OPEN EXTERNAL SUPPLY STOPS. YES CRITICALLY LOW BATTERY. INSTALL NEW BATTERY. YES REPEATED DOUBLE FLASH ON SENSOR? NO RECONNECT BATTERY TO SENSOR. DOES SENSOR FLASH FOR 5 SECONDS? 1 2 NO NO YES 1 2 DEAD BATTERY. INSTALL NEW BATTERY. REPEAT. CHECK FOR DAMAGE TO SENSOR WIRE INSULATION. REPLACE SENSOR. REPLACE SOLENOID WATER IS CONTINUOUSLY RUNNING RECONNECT BATTERY TO SENSOR.
PAGE 10
NextGen Selectronic® M970210-0070A SCREW Integrated Faucet with Optional Above-Deck Mixing & SmarTherm® Temperature Limiter M910297-0070A 0.35 GPM AERATOR M970354-0070A THERMOSTATIC VALVE ASSEMBLY M964172-0070A 0.5 GPM AERATOR M964171-0070A 1.5 GPM AERATOR MODEL NUMBERS 7755.1xx 775B.1xx 7755.2xx 775B.2xx 7755.3xx 775B.