Installation Guide

ManualsBrandsAmerican Standard ManualsDrop-in Kitchen SinksQuince Drop-in Cast Iron 33 in. 3-Hole Single Bowl Kitchen Sink in Brilliant White

SAVE FOR FUTURE USE

740210-100 (9/18)

Adjustable Wrench

Channel Locks

Regular Screwdriver

Phillips Screwdriver

10'

Saber Saw

Pipe Wrench

Level

Tubing Cutter

Square

Tape Measure

Electric

Drill

1 2 3 4 5 6 7 8 9 10 11

1 2 3 4 5 6 7 8 9 10

11 12 13 14 15 16 17 18 19 20 21 22 23 24

Hacksaw

Sealant

RECOMMENDED TOOLS AND MATERIALS

MOUNTING OPTIONS

REPLACEMENT USE

Under Mount

Installation

COUNTERTOP

When replacing an original unit be sure to shut off

water supply before removing the sink or disconnecting

water supply lines and drain fittings. Original supplies

and shutoff valves should be replaced on installation.

Sink can accommodate any standard 3-1/2" (89 mm) sink outlet drain.

APRON FRONT CAST IRON KITCHEN SINK

Under Mount Sink

INSTALLATION INSTRUCTIONS

CARE AND MAINTENANCE

CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

NOTE: Pictures may not exactly define contour of components.

CAUTION: RISK OF PERSONAL INJURY OR PRODUCT DAMAGE.

NOTE: Cast iron sinks are very heavy. Get help lifting the sink into place.

Thank you for selecting American Standard - the benchmark of fine quality for over 140 years. To ensure this product is installed

properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be

sure your installation conforms to local codes.

OBSERVE LOCAL PLUMBING AND BUILDING CODES

Before installing the sink, inspect it for damage. DO NOT install a damaged unit.

Notify your American Standard distributor of any damage. Return sink in original packing.

Product names listed herein are trademarks of AS America, Inc.

INSTALLATION PROCEDURES

Typical installation includes cabinet support preparation, installation of faucet, connection of flexible water supply

lines, attachment of sink to cabinet, sizing and installation of drain, supplies to house water system.

Sink Mounting Provisions – Whether the sink is used for replacement or new installation, the cabinet area beneath

the sink must be reinforced to provide sufficient support. Cast Iron Sinks are very heavy and the structure built to

support the sink must be able to support a minimum of 350 pounds. Also the cabinet and frame shown in the

instructions are generic and may not represent the actual design or structure.

CABINET SUPPORT PREPARATION

Important Note: It is recommended that the installation be performed by a professional and shall be in accordance

with all local plumbing and building code requirements.

Summary of content (5 pages)

PAGE 1
INSTALLATION INSTRUCTIONS CARE AND MAINTENANCE APRON FRONT CAST IRON KITCHEN SINK Under Mount Sink Thank you for selecting American Standard - the benchmark of fine quality for over 140 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes. ! CAUTION: PRODUCT IS FRAGILE.
PAGE 2
1 UNDER MOUNT INSTALLATION There are many ways to install an undermount sink and the detail of installation will depend on the design and quality of your cabinets and countertop. Next measure the actual size of the sink being installed to determine cabinet opening dimensions and support frame location. The cabinet opening should equal the maximum dimensions of the sink to ensure a minimum gap between the sink apron and the cabinet.
PAGE 3
SINK INSTALLATION CAUTION: Sink is heavy. For personal safety, use extra person for assistance with installation. STEP 1. Carefully set the sink within the support frame and position in center of cabinet opening. Ensure that the sink top rim is level and flush with cabinet top surface. Check clearance around sink apron and ensure sink is centered within cabinet opening. Ensure sink base is making proper contact with support frame. Adjust or shim as needed to obtain proper sink position and fit.
PAGE 4
5 APPLY SEALANT For Under Mount Sinks: Carefully wipe clean the sink apron and top rim free from all debris. Ensure that the surface on underside of countertop cutout opening is smooth and free of debris. Under mount installation requires a generous bead of sealant around the sink top rim where sink and countertop underside will make contact. APPLY SEALANT ON TOP THREE SIDES OF RIM TOP OF CABINET 6 INSTALL COUNTERTOP Carefully position and install the countertop.
PAGE 5
CARE & CLEANING TIPS ON AMERICAN STANDARD ENAMELED CAST IRON PRODUCTS American Standard brand cast iron is extremely durable, although care must be taken when handling and cleaning. For example, dropping a cast iron sink several inches from a cement floor can result in damage which will fracture the enamel surface. This damage usually manifests itself in the form of chips, shatters, or spiderweb cracks known as "crazing.