Installation Guide

ManualsBrandsAmerican Standard ManualsPlumbing ProductCulinaire Mounting Clip Kit (14-Pack)

CULINAIRE COLLECTION™

STAINLESS STEEL

KITCHEN SINKS

MODELS 7501.103, 7502.103, 7502.403,

7504.103, 7507.103, 7510.103

790767-100

Thank you for selecting American-Standard...the benchmark

of fine quality for over 100 years.

To ensure that your installation proceeds smoothly--please

read these instructions carefully before you begin.

BEFORE YOU BEGIN...

(965mm)

CULINAIRE DUAL LEVEL SINK

WITH DRAIN BOARD

MODEL 7510

32-1/8

(816mm)

CULINAIRE DOUBLE BOWL SINK

MODEL 7502

(432mm)

CULINAIRE ISLAND SINK

MODEL 7507

SELF RIMMING

24-1/4

(616mm)

21-1/8

(537mm)

CULINAIRE SINGLE BOWL SINK

MODEL 7501

(813mm)

CULINAIRE DUAL LEVEL

BOWL SINK

MODEL 7504

Certified to comply with ANSI A112.19.3M

CAN/C.S.A. B-45

Observe local plumbing and building codes.

IMPORTANT: DIMENSION OF FIXTURES ARE NOMINAL AND MAY VARY WITHIN

THE RANGE OF TOLERANCES ESTABLISHED BY A.N.S.I. AND C.S.A. STANDARDS.

©AMERICAN STANDARD INC. 2002

™

Unpack new sink and inspect carefully for

damage. Replace the sink in its original packing

carton to protect it until you are ready to begin

installation.

CUTOUT DIMENSIONS FOR SINKS:

Recommended Tools & Materials

Countertop Cutout Dimensions

Putty Knife

Pipe Wrench

Channel Locks

Long Phillips Screwdriver

or Regular Screwdriver

Adjustable Wrench

Drill

Below are the dimensions needed to determine the cutout size

for each sink. Select the correct diagram for your sink and refer

to the instructions below.

Locate and mark center lines of sink on countertop.

Provide proper clearance under the countertop for the faucet

supply lines and the structural parts of the cabinet.

By using the diagrams below and measuring your sink, draw the

outline of the sink cutout onto the countertop. This is the cutting

outline.

Remember that the size of the sink is larger than the cutout.

Basin Wrench

Saber Saw

Plumber's Putty or Caulk

Tubing Cutter

Tape Measure

Hacksaw

Mineral Spirits

Silicone Sealant

21-1/8

(537mm)

(533mm)

Summary of content (8 pages)

PAGE 1
™ SELF RIMMING CULINAIRE COLLECTION™ STAINLESS STEEL KITCHEN SINKS MODELS 7501.103, 7502.103, 7502.403, 7504.103, 7507.103, 7510.103 Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. BEFORE YOU BEGIN... 790767-100 CUTOUT DIMENSIONS FOR SINKS: Unpack new sink and inspect carefully for damage.
PAGE 2
7 AFTER THE CUTOUT IS DRAWN... 1 Perimeter of sink Drill a clearance hole inside the cutout line as marked on the countertop. 8 Cutout 2 Cut opening on cut line inside the perimeter of sink. Note - Formica countertop installation only is illustrated. Contact your countertop distributor for the best method of cutting other materials such as marble, hard synthetics, etc.
PAGE 3
Tightening Sequence For Clips 11 3 1 9 11 6 2 4 13 7 5 9 7 8 6 10 8 12 2 4 12 10 3 MODEL 7501 1 1 5 14 MODEL 7502 & 7504 3 11 5 1 3 13 5 8 9 7 7 6 10 8 4 2 12 MODEL 7507 ©AMERICAN STANDARD INC.
PAGE 4
Maintenance for stainless steel sinks: To keep the original quality of your Stainless Steel Sink, we recommend regular cleaning. Use a mild liquid dish detergent and water to clean the product after use. Rinse carefully and dry. Please have the following in mind: • Don't let water or other liquids dry on the product. Liquids that are left to dry leave a grey build-up stain on the steel. • Stainless steel can stand hard treatment, but sharp objects can easily scratch the surface.
PAGE 5
™ Installation Instructions STAINLESS STEEL SINKS UNDERCOUNTER MOUNTING FOR CULINAIRE™ COLLECTION STAINLESS STEEL KITCHEN SINKS MODELS 7501.000, 7502.000, 7504.000, 7507.000 Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. Certified to comply with ANSI A112.19.3.M CAN/C.S.A. B-45 Observe local plumbing and building codes.
PAGE 6
IMPORTANT: DIMENSIONS OF FIXTURES ARE NOMINAL AND MAY VARY WITHIN THE RANGE OF TOLERANCES ESTABLISHED BY A.N.S.I. AND C.S.A. STANDARDS. SUPPORT CLIP LOCATIONS: MODEL 7502.000 MODEL 7507.000 SUPPORT CLIPS MODEL 7504.000 MODEL 7501.
PAGE 7
1 4 Countertop Countertop Drill a clearance hole inside the cutout line. Mount the faucet and drain assembly following the manufacturer's instructions. Template Cutout template 2 5 Cut opening on cut line of the template. Note - Contact your countertop distributor for the best method of cutting materials such as marble, hard synthetics, etc. Connect supply lines to faucet finger tight, and carefully bend to engage with the supply stops. Tighten connections to faucet for secure seal.
PAGE 8
Maintenance for stainless steel sinks: To keep the original quality of your Stainless Steel Sink, we recommend regular cleaning. Use a mild liquid dish detergent and water to clean the product after use. Rinse carefully and dry. Please have the following in mind: • Do not let water or other liquids dry on the product. Liquids that are left to dry leave a grey build-up stain on the steel. • Stainless steel can stand hard treatment, but sharp objects can easily scratch the surface.