Acrylux Builder Series Bath Tub Walls Installation Instructions

ManualsBrandsAmerican Standard ManualsIndoor FurnishingAcrylux Builder Series Bath Tub Walls 6030Y1.BWT.XXX

754284-100 Rev. A

Product names listed herein are trademarks of AS America, Inc.

INSTALLATION INSTRUCTIONS

Models: 6030Y1.BW.XXX

6030Y1.BWT.XXX

6032Y1.BW.XXX

6032Y1.BWT.XXX

Acrylux Builder Series

Bath Tub Walls

Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please

read these instructions carefully before you begin. Local building codes vary by location. Observe all local plumbing and building codes.

= stud location = stud location

6030Y1.BW.XXX

6030Y1.BWT.XXX

6032Y1.BW.XXX

6032Y1.BWT.XXX

6030 STUD LAYOUT:

The Acrylux Tub Wall will

fit all standard 30" x 60"

bathtubs.

6032 STUD LAYOUT:

The Acrylux Tub Wall will

fit all standard 32" x 60"

bathtubs.

RECOMMENDED TOOLS

Tape Measure Pencil Level Screwdriver Screws, 1" Flathead, Stainless

Caulk Gun Drill Hole or Saber Saw Safety Glasses

MATERIALS:

• 2 Tubes of Adhesive Compatible with Polystyrene

• Screws, 1" Flathead Stainless

• 2" Masking Tape

• Caulk (for Faucet Installation)

• Shims

31-1/2"

800mm

60"

1524mm

60"

1524mm

30"

762mm

Back Panel

Side

Panel

(

1473mm

)

Door Openin

33-1/2"

838mm

60"

1524mm

(

1473mm

)

Door Openin

60"

1524mm

32"

813mm

Back Panel

Side

Panel

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Acrylux Builder Series Bath Tub Walls Models: 6030Y1.BW.XXX 6030Y1.BWT.XXX 6032Y1.BW.XXX 6032Y1.BWT.XXX Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. Local building codes vary by location. Observe all local plumbing and building codes.
PAGE 2
INSTALLATION INSTRUCTIONS IMPORTANT • Allow panels to reach room temperature before installation. • Before you begin, locate appropriate product reference (see page 1). • Read installation instructions carefully before starting project. • Keep instructions for warranty information. • Caulk will be necessary when installing bathtub walls. STEP 1. PREPARING ALCOVE • Strip alcove to the bare studs.
PAGE 3
INSTALLATION INSTRUCTIONS (continued) STEP 4. INSTALLING TUB WALL IN ALCOVE • Apply a generous bead of adhesive below mark on each back wall stud only (follow adhesive manufacturer’s recommended instructions). • Position back panel in place and press firmly against studs to assure full contact with adhesive. • Apply adhesive to studs for side panel opposite the shower controls. • Push side panel firmly into place. • Apply adhesive to each stud for faucet side panel and push panel firmly into place. (Fig.
PAGE 4
SCRATCH REMOVAL INSTRUCTIONS 1. For effective scratch removal and polishing, you will need to purchase these items: 1 sheet 1000 grit 3M® wet-dry sandpaper 1 sheet 1500 grit 3M® wet-dry sandpaper 1 sheet 2000 grit 3M® wet-dry sandpaper 1 small container of 3M® rubbing compound #05933 These items can be purchased at most auto supply stores that provide supplies to professional paint and body shops. Call before you go. Not all auto supply stores will have these items. 2. Start sanding with 2000 grit paper.