Instructions / Assembly

ManualsBrandsAmerican Standard ManualsAlcove Shower DoorsOvation 48 in. x 72 in. Semi-Frameless Bypass Shower Door in Satin Nickel and Clear Glass

710285-100 Rev. E

Product names listed herein are trademarks of AS America Inc.

Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed

properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure

your installation conforms to local codes.

INSTALLATION INSTRUCTIONS

OVATION 48 in SHOWER DOOR

MODEL: AM00548.400 SERIES

REQUIRED TOOLS AND MATERIALS

GENERAL INFORMATION

Please inspect the product immediately upon receipt for transit damage, missing packs/parts or manufacturing

fault. Damage reported later cannot be accepted. Please handle the product with care avoiding knocks and

shocks loading to all sides and edges of the glass.

NOTE: TEMPERED GLASS CANNOT BE DRILLED, CUT OR MODIFIED.

READ THE INSTRUCTIONS CAREFULLY

Familiarize yourself with all the parts as shown in the assembly drawing. The assembly drawing will also

provide a helpful reference when relating the location of the various parts and how they are mounted.

Special care should be taken when drilling walls to avoid hidden pipes or electrical cables.

Note: This product is heavy and may require two people to install.

AFTER-CARE INSTRUCTIONS

After use, your shower should be cleaned with soap and water. This is particularly important in hard water

districts where insoluble lime salts may be deposited and allowed to build up. Cleaners of a gritty or abrasive

nature should not be used. Care should be taken to avoid contact with strong chemicals such as organic

solvents and strippers.

Glass cleaners can be used but with caution, if in doubt contact the manufacturer of the cleaner in question.

Please keep these instructions for aftercare and customer service details.

For problems please contact American Standard. Do not return to store.

Regular ScrewdriverPhillips Screwdriver

10'

Caulking Gun & Caulking

Drill 1/4" & 1/8" Drill Bits

#2 Square Drive Bit

Level

Tape Measure

Hammer Pencil

SAVE FOR FUTURE USE

Summary of content (9 pages)

PAGE 1
INSTALLATION INSTRUCTIONS OVATION 48 in SHOWER DOOR MODEL: AM00548.400 SERIES Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.
PAGE 2
BOX CONTENTS 1x Top Horizontal Rail 1x Bottom Horizontal Rail 1x Lube INSTALLATION INSTRUCTIONS OVATION 60 in SHOWER DOOR MODEL: AM00560.400 SERIES Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.
PAGE 3
ASSEMBLY DRAWING Illustrated with Sliding Glass Panel on left and Fixed Glass Panel on right. Glass Panels may be reversed.
PAGE 4
INSTALLATION NOTES: This unit is best installed by two people. Cover drain with tape prior to installation to prevent the loss of small parts. Unpack your unit carefully and inspect for freight damage. Lay out and identify all parts using instruction sheet as a reference. Before discarding the carton check to see that no small hardware parts have fallen to the bottom of the box. If any parts are damaged or missing refer to the description noted in the instructions when inquiring about replacements.
PAGE 5
1 ASSEMBLE FRAME (CONTINUED) 4A - 4B Slide Wall Posts (5) on each end. The Wall Posts fit inside Door Posts of the frame. 5A - 5B Attach Center Guide (9) to Bottom Horizontal Rail using screw as shown in 5A. Use the hole closest to side that will have Fixed Glass Panel (17). Fill the remaining hole with silicone sealant. Insert Center Guide Spacer (10) as shown in 5B.
PAGE 6
3 INSTALLING FRAME 2 PEOPLE REQUIRED 1. Secure assembly to wall using previously drilled holes. 2. Install Screw Cover Caps. VIEW FROM INSIDE 2 1 Screw M4x35 (2) 4 FIXING ASSEMBLY TO WALL POSTS Ensure Door Assembly is centered in opening. Push down to top of shower base before anchoring screws to Wall Posts. 1A & 2A Drill Pilot Holes 1B & 2B Secure door posts to wall posts with screws 1C & 2C Snap Cap in place VIEW FROM INSIDE 1A 2A 1 2 Ø1/8" Bit [Ø3.
PAGE 7
5 LOCATING SLIDING GLASS DOOR PANEL The Sliding Glass Door Panel (7) may be placed on either the left-hand side or right-hand side of the assembled frame. 1B 1A It is recommended that the Sliding Glass Door Panel is installed on the same side of the shower enclosure as the shower head. This will allow the water temperature to be adjusted prior to entering the shower enclosure.
PAGE 8
7 INSTALLING SLIDING GLASS DOOR PANEL & HANDLE SET 1A-1C Install Top Rollers (12) facing outward, on the Sliding Glass Door Panel (7). With the Top Rollers installed, place bottom of Sliding Glass Door Panel in the Center Guide (9) and insert the Top Rollers into the Top Horizontal Rail (13). Add lubricant to Top Rollers. 2A-2B Install the Handle (4) on the Sliding Glass Door Panel ensuring the long portion of the Handle faces inward.
PAGE 9
MAINTENANCE: Two primary materials are used to manufacture your new American Standard shower enclosure: tempered glass and anodized aluminum. To assure a long lasting finish on the enclosure, wipe it down with a towel after each use. For occasional, more concentrated cleaning efforts Lysol Non-Abrasive Bathroom Cleaner works extremely well. Be sure that any over spray falling on the aluminum frame is rinsed thoroughly and dried.