Use and Care Guide

ManualsBrandsAmerican Standard ManualsBathtub DoorsAM00750.422.213

710006-100

OPTIONAL

H-JAMB

TOP TRACK

PANEL

GUIDE

CLIPS

1-3/16

ROLLER

OUTER

PANEL

ASSEMBLY

INNER

PANEL

ASSEMBLY

STANDARD

WALL

JAMB

Installation Instructions

FRAMED BY-PASS

SHOWER DOORS

Thank you for selecting our product...the benchmark of fine quality for over 100 years. To ensure that your installation

proceeds smoothly--please read these instructions carefully before you begin.

Record Model Number _______________

BEFORE YOU BEGIN...

Local building codes vary by location. Observe all local plumbing and building codes.

Unpack your new shower doors and inspect them carefully for damage. Verify that the doors are the correct size for your installation.

TOOLS & MATERIALS REQUIRED...

• Tape Measure • Electric Drill • Level • Phillips Screwdriver • Drill Bits 1/8" & 3/16" • Masking Tape • Silicone Caulk

IMPORTANT: Record the Model No. (see carton) of your shower door for future reference. Model No. ____________

READ THE INSTRUCTIONS CAREFULLY. Familiarize yourself with all the parts shown in the exploded view. The exploded view will

be helpful when locating and installing the various parts.

Summary of content (7 pages)

PAGE 1
Installation Instructions FRAMED BY-PASS SHOWER DOORS Thank you for selecting our product...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. Record Model Number _______________ 710006-100 BEFORE YOU BEGIN... Local building codes vary by location. Observe all local plumbing and building codes. Unpack your new shower doors and inspect them carefully for damage.
PAGE 2
1 2 INSTALLATION PROCEDURES: If using standard wall jambs cut bottom track 3/16" shorter than length “D”. Measure length “D” at the center of the tub ledge. If using H-jamb (1391-1) cut bottom track 1-3/16" shorter than length “D”. If using HOC or HUR jamb, temporarily place wall jambs on wall and measure distance from wall jamb to wall jamb on inside. Cut the bottom track to that length. D For best results use a 32 tooth hacksaw blade and a miter box.
PAGE 3
5 6 Apply thick beads of caulk to underside of bottom track as shown. Close tub/shower drain before proceeding. Remove bottom track and wall jambs. Return bottom track to the previously marked location. When installing on a fiberglass or plastic unit use a 1/8" drill bit and do not use the plastic screw anchors. When installing on all units other than fiberglass or plastic use a 3/16" drill bit and the plastic screw anchors.
PAGE 4
10 9 Install header over each end of wall jambs. Mount nylon rollers to slot on the top of each door. Drill a 1/8" hole through header and into wall jamb from inside at each end (1/4" from the wall). *The nylon side of roller should be facing same way as towel bar. Fasten header to wall jamb with screws provided. ROLLER ROLLER SCREW ROLLER MOUNTING FLANGE (ACTUAL SIZE) OUTER PANEL INNER PANEL For towel bar installation see TOWEL BAR INSTALLATION GUIDE.
PAGE 5
13 1. Caulk the gap at both ends between bottom track and wall jambs. 2. Caulk along inside and outside of shower/tub door where the metal touches the shower stall, providing a water tight seal. 3. Allow 24 - 48 hours to dry before using. 2 1 INSIDE HOW TO CARE FOR YOUR ENCLOSURE Do not use scouring powder, pads or sharp instruments on metal or glass panels. Occasionaly wipe with mild detergent diluted in water to keep the panels and metal parts looking new.
PAGE 6
TOWEL BAR INSTALLATION GUIDE PACER The towel bars are attached on the inside of the inside panel and the outside of the outside panel by using two 1" flat head thread forming tapping screws. See diagram OUTSIDE PANEL INSIDE PANEL ACTUAL SIZE PRESTIGE To attach to the panel: 1. Push left side towel bar brackets into left side of towel bar extrusions and right towel bar brackets into right side of towel bar extrusions.
PAGE 7
AS AMERICA, INC. LIMITED LIFETIME WARRANTY FOR SHOWER DOORS AS America, Inc. (“American Standard”) warrants to the original consumer purchaser that it will, at its sole option, repair or replace this product or any part of this product, if it confirms that the product is defective in materials or workmanship under normal use and maintenance for the lifetime of this product. This warranty does not apply to commercial installations. Commercial installations shall have a limited warranty of 3 year(s).