INSTALLATION INSTRUCTIONS FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE WITH NO POST QCI5239 QCI5239 Rev 0 Page 1 Certified 06/20/2016
INSTALLATION NOTES: Unpack your unit carefully and inspect for freight damage. Lay out and identify all parts using the instruction sheet as a reference. Before discarding the carton, check to see that no small hardware parts have fallen to the bottom of the box. If any parts are damaged or missing, refer to the descriptions noted in the instructions when contacting your dealer for replacements. Handle the glass panel(s) carefully and protect the edges.
Parts List A. B. C. D. E. F. G. H. I. J. K. Curb (w/ weep holes) (1) Plastic wall anchor (6) #8 x 1 1/2” Truss Head Screw (6) Wall Jamb (2) Plastic Setting Block (2) Stationary Glass Panel (1) Header (1) #8 x 1/4” Truss Head Screw (5) Vertical Glazing Vinyl (2) Horizontal Glazing Vinyl (4) Door Assembly (1) K1. Hinge Jamb (1) K2. Hinge Rail (1) L. Curb Snap-in Filler (1) M. Header Snap-in Filler (1) N. Strike Vinyl (1) O. Magnet (1) P. Polycarbonate Strike Jamb (1) Q. Latch Vinyl (1) R. Latch (1) S.
1 The Frameless Continuous Hinge Shower Enclosure must be installed with the door hinged off of the wall. It may be installed hinge right or hinge left. But, for maximum leak protection, the hinge side be opposite the shower head. Using the illustration, determine the proper hinge side for the door. Careful as to not follow the illustrations exactly. CAUTION: For safety reasons, the door must always open outward.
4 #8 X 1/2” SCREW Wipe the shower walls, sill, curb & wall jambs with a clean, dry cloth to remove any dust or debris. Apply a 1/4” bead of silicone along the inside of the pencil lines that were marked in Step #2. Carefully place the curb on the sill, over top the silicone, in the position marked. BE SURE THE WEEP HOLES FACE THE INTERIOR. Silicone the inside of the curb at both ends where it meets the wall.
7 Slide the header over the wall jambs. Using the two holes on the interior face of the header as a guide, drill a 1/8” hole into each wall jamb. Attach the header to the wall jambs using two #8 x 1/4“ Truss Head screws [H]. DOO OPEN R ING #8 X 1/4” SCREW DOO OPEN R ING TIP: Slide the glass panel out of the wall jamb before drilling to prevent damaging the panel. #8 X 1/4” SCREW Measure the door panel width.
10 Orient the door [K] to the opening. Grab the door HEADER from the inside. The open side of the hinge jamb [K1] should be away from you. (see illustration) Carefully lift the door into the opening and slide the hinge jamb completely over the available wall jamb. EXTERIOR SNAP-IN VINYL FILLERS Holding the door in the open position; 1. Check the curb and header length 2. Trim if necessary 3. press the curb snap-in filler [L] into the curb, WITH THE CURB RAISED LIP ON THE EXTERIOR.
13 Grab the remaining vinyl pieces from Step #9. Cut two (2) pieces of the vertical vinyl [I] 1” longer than the vertical opening. Remove the tape from the glass. Starting on the exterior, slide one end of the vertical vinyl up into the header and press into the wall jamb about 6” down. Apply light pressure against the interior of the glass panel to hold vinyl in place and install vinyl on the interior in a similar fashion. Press the vinyl into the wall jamb alternating between the interior and exterior.
16 Remove the magnet and slide the vinyl partially out of the header snap-in filler. Trim enough of the vinyl so that the magnet is not covered by the lip of the polycarbonate strike jamb (approximately 3/8” should suffice). Slide the vinyl back into the filler and replace the magnet. Place a small amount of silicone at the end of the magnet to hold in place.
21 Place the sweep back onto the bottom of the door. Step inside the shower and close the door. Mark on the sweep at the edge of the polycarbonate strike jamb. INTERIOR Open the door and remove the sweep. Trim the deflector lip and the inside portion of the sweep. Replace the sweep and close the door. Check for clearance. The lip of the strike jamb should touch the glass not the sweep.
Back-to-Back Door Pull Installation Instructions A B C D E F G A Interior handle (1) Exterior handle (1) Metal washer (4) Large clear disc (4) Small clear disc (4) Hole sleeve (2) Stud screw w/ collar (2) E D D B E G C F C STEP 1 Using the provided Allen wrench, loosen the two set screws located on the under side of one of the handles near the washers. Seperate the handle from the stud screws and collars.
“C” Pull Handle / Towel Bar Combination Installation Instructions There are eleven hardware components for the Combination Door Pull and Towel Bar mounting: One pull; one towel bar; two end caps with threaded studs; one stud head screw; and six clear gaskets to act as a buffer between the hardware and the glass. Take the stud head screw and both end caps with a stud protruding and sleeve a clear gasket on each of the screws. The towel bar will be mounted first.
