Bidet Fitting Installation Instructions

ManualsBrandsAmerican Standard ManualsIndoor FurnishingAmarilis 8391.000

Installation

Instructions

.3&7

Certiﬁed to comply with ASME A112.18.1M

U.S. Patent No. 5,819,789

Roughing-in Dimensions

Turn off hot and cold water

supplies before beginning.

CAUTION



BIDET FAUCET INSTALLATION

Place MOUNTING NUTS (1) onto the VALVE BODIES

(2) and insert VALVE BODIES (2) through outside

holes, from underside of the BIDET LEDGE. Drop the

RUBBER RING (3) over the VALVE BODIES (2) and

screw on the ESCUTCHEON (4) until it locks against

the internal stop.

Tighten the MOUNTING NUT (1) to secure the

VALVE BODY (2).

Replace UPPER GASKET (7) and FRICTION RING (10).

Position the side threaded outlet rearward and secure

MOUNTING NUT (9). Thread ESCUTCHEON (5) onto

TRANSFER VALVE (8) until it seats against the

BIDET LEDGE.

Remove MOUNTING NUT (9), FRICTION RING (10)

and UPPER GASKET (7) from TRANSFER VALVE (8)

and insert into the center forward hole of BIDET.

COLD

HOT

BIDET

LEDGE

BIDET OUTLINE

IS SYMBOLIC

FINISHED

WALL

1-1/4 O.D. TAILPIECE

ADJ. 1-1/4

TO 2-1/4

3-7/8

5-1/2

1-3/8

DIA.

7/8 DIA.

TRANSFER VALVE (FOR FLUSHING

RIM OR SPRAY)

DOUCHE SPRAY

2-1/8

DIA.

8391.000

BIDET FITTING

FINISHED

FLOOR

DIVERTER AND

VACUUM BREAKER

ASSEMBLY

1-1/4 MAX.

1-3/16 DIA.

(C)

(H)

4-1/4

FOR GROUND JOINT

CONNECTION OR 1/2 "

O.D. SLIP (INLETS)

REAR VIEW WITH

WALL REMOVED

8 TO 12

2-1/4

DIA.

Congratulations on purchasing your American Standard faucet

with EverClean nish found only on American Standard faucets.

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

with EverClean™ Finish

*Hex key

*Wrench

*Supplied with Fitting

Flat Blade Screwdriver

Adjustable Wrench

Channel Locks

Phillips Screwdriver

Required Tools

5VCJOH$VUUFS

EverClean Finish

• One wipe eortlessly removes spots

• Eliminates the need for cleaners and scrubbing

• Permanent surface protectant remains beautiful

for the life of the faucet

• EverClean™ available on: Polished Chrome, Satin Nickel,

Stainless Steel, Polished Brass (or any combination of these nishes)

Summary of content (3 pages)

PAGE 1
Installation Instructions 8391.000 BIDET FITTING with EverClean™ Finish Congratulations on purchasing your American Standard faucet with EverClean finish found only on American Standard faucets.
PAGE 2
DRAIN INSTALLATION Assemble SPRAY BODY (1) to BIDET. Using putty, seal underside of SPRAY BODY FLANGE (2) and secure with NUT (3). Assemble O-RING (1), WASHER (2), PIVOT ROD (3) and NUT (4) to DRAIN BODY (5). Concave side of cup WASHER (2) is toward ball. Thread LOCKNUT (6), WASHER (7) and GASKET (8) onto DRAIN BODY (5). 9 Feed DRAIN BODY (5) up through BIDET and thread FLANGE (9) fully onto BODY (5). Push DRAIN ESCUTCHEON (10) onto TAILPIECE (11).
PAGE 3
WATER SUPPLY CONNECTIONS NOTE: FLEXIBLE SUPPLIES OR BULL NOSE RISERS ARE NOT INCLUDED AND HAVE TO BE PURCHASED SEPARATELY. 1 Connect water supplies to FAUCET (1) with 1/2" IPS FLEXIBLE SUPPLIES (2) or 3/8" O.D. BULL-NOSE RISERS (3). Use adjustable wrench to tighten connections. 2 Do not over tighten. Be careful not to kink copper supply when bending. Use tubing cutter to cut to proper length. COUPLING NUT 3 FERRULE FINISH DRAIN INSTALLATION 2 Position BIDET fixture and secure to floor.