User's Manual

ManualsBrandsAmerican Standard ManualsOutdoor Kitchen IslandAmerican Standard American Standard Outdoor Kitchen Island 6058.105

Installation InstructionsInstallation Instructions

(In Toronto Area only: 1-905-3061093)

CERATRONIC™

Proximity Faucet with Touch-Free

Temperature Control

To l e a r n more a b o u t Amer i c a n S tandard Fa u c e t s v i s i t o u r website a t : www.us.amstd.com or U.S.

customer's e-mail us at: faucetsupport@amstd.com

For Parts, Service, Warranty or other Assistance,

please call

1-800-442-1902 (In Canada: 1-800-387-0369)

NOTE TO INSTALLER: Please give this manual to the customer after installation.

(In Toronto Area only: 1-905-3061093)

Certiﬁed to comply with ASME A112.18.1M

M 9 6 8 857 R EV.1. 2

Product No.'s & Options

Speciﬁcations

How to Install

Electrical Hook-up

Operation

Maintenance

FAQ,s

Replacement Parts

2-3

5-6

6-8

PRODUCT NUMBERS

6058.105

6058.102

M 9 6 8 857 R EV.1. 2

Summary of content (11 pages)

PAGE 1
Installation Instructions CERATRONIC™ PRODUCT NUMBERS Proximity Faucet with Touch-Free Temperature Control Certified to comply with ASME A112.18.1M © 2006 American Standard M 9 6 8 8 5 7 R E V. 1. 2 6058.105 6058.102 Product No.'s & Options 1 Specifications 2 How to Install 2-3 Electrical Hook-up 4 Operation 5-6 Maintenance 6-8 FAQ,s 8 Replacement Parts 9 NOTE TO INSTALLER: Please give this manual to the customer after installation.
PAGE 2
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. UNPACKING All American Standard Faucets Are Water Tested At Our Factory. Some Residual Water May Remain In The Faucet During Shipping. 1. Remove the fitting and loose items from the carton. The illustration below shows the fitting and all loose items after they have been removed from the carton.
PAGE 3
Roughing-in Dimensions 183mm (7-3/16) 190mm (7-7/16) GENERAL DESCRIPTION: Electronic faucet with proximity operation. Colored LED's signal temperature change mode. Vandal resistant solid brass construction single post mounting. Operates on AC permanent power. Water pressure range from 20 to 80 psi. In-line strainer for solenoid is integral. Single inlet 3/8 compression, built-in checks, and flexible stainless steel 15" reach inlet hose for spout connection. 143mm (5-5/8) 132mm (5-3/16) 55mm D.
PAGE 4
2 MOUNT ENCLOSURE; Fig. 2 Fig. 2 1. Determine location of ENCLOSURE (1). It must be located with-in the 14" (356mm) by 21" (533mm) shaded area shown in Fig. 2 in order for electrical connections from the spout assembly to be made. NOTE: ENCLOSURE SUPPLY HOSE is 20". Distance between wall supply and ENCLOSURE (1) must be taken into consideration. LAVATORY RIM OR MOUNTING SURFACE 14" (356mm) SUPPLIES ENCLOSURE MOUNTING HOLES 1 2-3/4" (71mm) 2. Remove 4 screws from COVER (2) and pull off COVER (2).
PAGE 5
Fig. 1 ELECTRICAL INSTALLATION 3 1 ELECTRICAL 1 2 1. Remove ENCLOSURE COVER (1). Fig. 1. 2. Remove CIRCUIT BOARD (2) from ENCLOSURE (3). (May have to pull cord of power supply through). Fig. 1. 3. Feed the WIRE CONNECTORS (4) through the top of ENCLOSURE (3). Fig. 1b. 4. Remove SPLIT PLUG (5) from GROMMET (6). Insert the gray SENSOR WIRE (7) and YELLOW and GREEN CONNECTOR WIRES (8) into SPLIT PLUG (5). Leave 4” of wire from end of SPLIT PLUG (5). Fig. 1c. Feed WIRES (7 & 8) through GROMMET (6).
PAGE 6
OPERATION Fig. 1 1 HAND WASH SENSOR OPERATION; BLUE SENSOR RED SENSOR Fig. 1 When the Sensor detects a user, the water immediately starts to flow. Water flow will stop Two seconds after user is out of sensor range. The off delay allows the user to comfortably move his hands without the flow cycling on to off. As a precaution, a safety timer will turn off the water, after the sensor has been blocked for 59 seconds. The water will stay off until the blockage is removed from the detection zone.
PAGE 7
3 HOW TO SET DEFAULT Fig. 23 Fig. Fig. 3a ADJUST COLD TEMPERATURE Fig. 3 BLUE SENSOR Note: The factory setting of the Default Temperature is at a position of even amounts of hot and cold water flows. This setting can only be changed within the first 15 minutes of switching on the power. ADJUST HOT RED SENSOR 1. Remove the power to the faucet by unplugging the Power Supply from the wall outlet. Wait 60 seconds, and then plug the Power Supply Back into the wall outlet. 2 .
PAGE 8
2 HOW TO CLEAN FILTER; Fig. 2 CAUTION Fig. 2 Before opening ENCLOSURE disconnect AC power supply. 1. Remove ENCLOSURE COVER. 2. Close SUPPLY STOPS. Note: Keep water flowing out of faucet while shutting off. 1 CLEAN SCREENS 4. Unthread STRAINER (1) using a 7/16" socket. 1 5. Pull out the STRAINER (1) and clean with an old toothbrush. Rinse thoroughly with water. INSTALL 6. Install the STRAINER (1) back in its place and tighten with a 7/16" socket. Caution: do not over tighten strainer.
PAGE 9
4 GENERAL CLEANING; Fig. 4 Fig. 4 1. For general cleaning use a damp, soft cloth to clean the spout and the sensor. 2. For cleaning dirt use a soft cloth with diluted dish washing detergent. Wipe the area using a wet cloth and dry using a soft cloth. CAUTION Do not scratch the sensor when cleaning. Avoid using anything that may scratch the spout surface. Never use polishing power, detergent or a nylon scrub brush. They will damage the surface of the spout or Sensor.
PAGE 10
CERATRONIC LAVATORY FAUCETS A960215-0070A SENSOR COVER (BLUE) PRODUCT NUMBERS 6058.105 6058.102 A960217-0070A TEMPERATURE SENSOR KIT A960216-0070A SENSOR COVER (RED) Replace the "YYY" with appropriate finish code M923827-YYYOA 2.2 GPM AERATOR 066508-YYYOA 0.
PAGE 11
M 9 6 8 8 5 7 R E V. 1.