Instructions / Assembly

ManualsBrandsAmerican Standard ManualsBathOvation 33.5 in. x 60 in. x 75.25 in. Combo 5-Piece Shower Kit in Arctic

STUD LAYOUT FOR WALL INSTALLATION FOR USE WITH 2603/2699 SHOWER BASE (SHOWN).

The studs should be located as shown to properly support walls. Provide additional studs where illustrated. (below)

NOTE: INSTALLATION

OVER GREENBOARD OR

FIREWALLS:

If installing wall panels over

greenboard and/or firewall

material and not directly on

the studs, your alcove

dimensions must consider

the thickness of this material.

Measure from the inside of

the finished walls.

754964-100 Rev. A

Product names listed herein are trademarks of AS America Inc.

NOTE: Take extra care in handling the front surfaces of the walls. Use only non-abrasive cloths to avoid scratching.

Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read

these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.

INSTALLATION INSTRUCTIONS

2603 & 2699 Series Wall Surrounds

Visit www.americanstandard.com for coordinating products.

USE WITH 2602 OR 2698 SERIES SHOWER BASES

REQUIRED TOOLS AND MATERIALS

BEFORE YOU BEGIN....

Local building codes vary by location. Observe all local plumbing and building codes.

Unpack your new shower walls and inspect them carefully for damage. Verify that the walls are the correct size for your installation.

Refer to American Standard roughing-in information for specific dimensions for each model.

Caulking Gun

Level

Square

Utility Knife

Pencil

Drill

Hole Saw or

Sabre Saw

Tape Measure

TOOLS:

Acrylic/Latex or Acrylic/Silicone Sealant

Galvanized (or corrosion resistant) flat head screws 3/4" minimum length

2 x 4 lumber for additional wall studs as required

Tub Surround Adhesive

1 x 4’s if installing shower doors

MATERIALS:

PREPARATION:

The 2603/2699 Series Wall Surrounds are to be installed directly

over stud walls. Drywall is not required.

A) Remove dry wall surface and ensure that alcove is plumb and square.

(Illustration 1)

B) Prepare studs as indicated below.

IMPORTANT:

C) Rough plumbing and fittings must be installed before walls.

Illustration 1

SAVE FOR FUTURE USE

Each alcove

stud must be

plumb and

square.

The 2699 Series Wall Surrounds are to

be installed directly over stud walls.

Drywall is not required.

LHO shown

(RHO opposite)

8-1/4"

(210mm)

8-1/4"

(210mm)

30"

(762mm)

5-3/4"

(146mm)

5-3/4"

(146mm)

12"

(305mm)

60"

(1524mm)

9-1/4"

(235mm)

9-1/4"

(235mm)

10"

(254mm)

10"

(254mm)

34"

(864mm)

The 2603 Series Wall Surrounds are to

be installed directly over stud walls.

Drywall is not required.

8-1/4"

(210mm)

8-1/4"

(210mm)

30"

(762mm)

12"

(305mm)

48"

(1219mm)

9-1/4"

(235mm)

9-1/4"

(235mm)

(203mm)

33-1/2"

(851mm)

Summary of content (6 pages)

PAGE 1
INSTALLATION INSTRUCTIONS 2603 & 2699 Series Wall Surrounds Visit www.americanstandard.com for coordinating products. USE WITH 2602 OR 2698 SERIES SHOWER BASES Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes. BEFORE YOU BEGIN....
PAGE 2
1 INSTALLATION PROCEDURES: If you plan to install a shower door, a 1 x 4 must be installed in the pocket on the back of both side walls. A) Cut one end of the 1 x 4 to 45° as shown. (Fig.1) Then cut the 1 x 4 to a length of 71-1/2" (1816mm). B) Apply a bead of tub surround adhesive in the pocket of each side wall. With 45° cut end down and angle facing out, attach board butting up to the top of the pocket. Allow time to cure.
PAGE 3
Pencil line A) Apply a bead of tub surround adhesive down each stud that will come in contact with the back panel being sure to stay below the line you marked. You do not need to apply adhesive to the corner studs. B) Lay a bead of sealant along the inside corner of the shower base ledge as shown in Fig. 2. TUB SURROUND ADHESIVE BEAD C) Reposition back panel aligned with pencil line and press firmly against studs. Fig.
PAGE 4
5 A) Apply a bead of tub surround adhesive down each stud that will come in contact with the side panels being sure to stay below the line previously marked. C) Align the top nailing flange of each side panel with pencil line marked. Press firmly into place to ensure proper adhesion to studs. Check alignment with all mating surfaces and reposition if necessary. B) Lay a bead of sealant along side panel mating surface and shower base ledge.
PAGE 5
6 7 Install temporary braces to hold the center of the back and side panels tight to the studs for approximately 24 hours while adhesive sets. Add cushioning between panels and braces to prevent scratching the panels. When installing greenboard, position drywall screws above the top nailing flange. If you choose to screw through the nailing flange, you MUST drill clearance holes in the flange to avoid cracking/damaging the flange.
PAGE 6
POST INSTALLATION CLEAN-UP Remove all construction debris. Tile grout can be removed with a wooden popsicle stick or tongue depressor. Do not use wire brushes or any other metal implement on surface. Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent. Stubborn dirt or stains may be removed using granular Spic and Span® mixed with water. Painter's naphtha can be used to remove excess adhesives and/or wet oil-base paint.