Cadet 1.6 GPF Two-Piece Pressure Assisted Toilets Installation Instructions

ManualsBrandsAmerican Standard ManualsIndoor FurnishingCadet 1.6 GPF Two-Piece Pressure Assisted Toilets 2366

INSTALLATION INSTRUCTIONS

CADET 1.6 GPF TWO-PIECE PRESSURE-

ASSISTED TOILETS

- Model 2333 Elongated

- Model 2366 Round Front

- Model 2377 Elongated - 16-1/2" High Bowl

Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this

product is installed properly, please read these instructions carefully before you begin. (Certain installations may

require professional help.) Also be sure your installation conforms to local codes.

RECOMMENDED TOOLS AND MATERIALS

Putty Knife Regular Screwdriver Adjustable Wrench Sealant Tape Measure

Hacksaw Wax Ring/Gasket Flexible Supply Tube Closet Bolts Carpenters Level

1 REMOVE OLD TOILET

a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.

b. Disconnect and remove supply line. NOTE:

If replacing valve, first shut off main water supply!

c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.

d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.

NOTE:

Mounting surface must be clean and level before new toilet is installed!

305mm

(12)

INSTALL CLOSET BOLTS

Install closet bolts in flange channel, turn 90

and slide into place 6" (152 mm) apart and

parallel to wall.

SAVE FOR FUTURE USE

DIMENSIONS (Nominal) NOTE:

Distance from wall to

closet flange centerline (rough-in) must be 12" (305 mm)

minimum.

CLOSET FLANGE

CLOSET BOLTS

730479-100 Rev. A

Saniwares

CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY

HANDLE WITH CARE!

NOTE:

For proper operation these products require a minimum of 20 psi line pressure

Product names listed herein are trademarks of American Standard Inc.

31 (787mm)

REF.

29 (737mm)

REF.

(737mm)

31-1/2

(800mm)

ADA HEIGHT

305mm

(12)

FINISHED

FLOOR

203mm

(8)

SUPPLY

REQ'D

FINISHED WALL

19-1/2

(495mm)

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS CADET 1.6 GPF TWO-PIECE PRESSUREASSISTED TOILETS - Model 2333 Elongated - Model 2366 Round Front - Model 2377 Elongated - 16-1/2" High Bowl ! CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE! NOTE: For proper operation these products require a minimum of 20 psi line pressure U S E Thank you for selecting American Standard - the benchmark of fine quality for over 100 years.
PAGE 2
4 5 WAX RING SEALANT NUT TAPERED WASHER FLANGE CLOSET BOLT INSTALL WAX SEAL Invert toilet on floor (cushion to prevent damage), and install wax ring evenly around waste flange (horn), with tapered end of ring facing toilet. Apply a thin bead of sealant around base flange. INSTALL TOILET ON FLANGE a. Unplug floor waste opening and install toilet on closet flange so bolts project through mounting holes. b. Loosely install retainer washers and nuts.
PAGE 3
10 9 TANK SET SCREW WATER INLET 1/32" APPROX. WASHER FLEXIBLE SUPPLY COUPLING NUT VALVE NUT COMPRESSION COLLAR TRIM PLATE VALVE ADJUSTMENTS CAUTION: Overtightening of COUPLING NUT could result in breakage and potential flooding. CONNECT WATER SUPPLY a. Connect water supply line between shutoff valve and tank water inlet fitting. Tighten COUPLING NUT 1/4 turn beyond hand tight. Check that refill tube is inserted into overflow tube. b.
PAGE 4
TROUBLESHOOTING GUIDE NOTE: The presence of a small amount of water in the bottom of the tank is normal. The air inducer is designed to leak for short periods during each flush cycle as a self-cleaning action. Drippage is drained into the bowl. If used on water system containing excessive sand and/or debris, a periodic cleanup of inlet strainer is recommended. (See enclosed instructions for strainer cleaning.