Island Sink Specification Sheet

ManualsBrandsAmerican Standard ManualsIndoor FurnishingChandler Americast 7182.000

CHANDLER™ AMERICAST™ ISLAND SINK

WITH FAUCET HOLES 7182.001/7182.803

WITHOUT FAUCET HOLES 7182.000

ISLAND SINK MODEL 7182.001/803

ISLAND SINK MODEL 7182.000

Installation

Instructions

791267-400 Rev. C

Thank you for selecting American-Standard...the benchmark

of fine quality for over 100 years.

To ensure that your installation proceeds smoothly--please

read these instructions carefully before you begin.

BEFORE YOU BEGIN...Unpack new sink and

inspect carefully for damage. Replace the sink

in its original packing carton to protect it until

you are ready to begin installation.

™

CUTOUT DIMENSIONS FOR SINK

Recommended Tools & Materials

Silicone Sealant

Putty Knife

Pipe Wrench

Channel Locks

Phillips Screwdriver

Regular Screwdriver

Adjustable Wrench

Drill

Locate and mark center lines of sink on countertop.

Provide proper clearance under the countertop for

the faucet supply lines and the structural parts of the

cabinet.

Cut out correct template and trace the cut line onto

the countertop at the proper location.

NOTE: If replacing an existing sink be certain to shut

off water supplies before removing old sink.

Mineral Spirits

Basin Wrench

Saber Saw

Tubing Cutter

Tape Measure

Hacksaw

Scissors

Product names listed herein are trademarks of American Standard Inc. unless otherwise noted.

6-23/32"

(171mm)

6-23/32"

(171mm)

14" (356mm)

14-1/2" Radius

(368mm)

14-1/2" Radius

(368mm)

15" (381mm)

3/4" (19mm)

CENTER LINE

SINK

OUTLINE

SINK

OUTLINE

1/2"TYP.

CUTTING

LINE

CUTTING

LINE

CUTOUT FOR NEW INSTALLATION

MODIFICATION REQUIRED TO FIT ISLAND SINK

WITH FAUCET HOLES INTO A STANDARD

15" X 15" SINK CUTOUT

NOTE: CHANDLER ISLAND SINK WITHOUT

FAUCET HOLES DOES NOT FIT INTO A

STANDARD 15" X 15" SINK CUT OUT

8-11/32"

(212mm)

14"

(356mm)

15 "

(381mm)

16-1/2" (419mm)

14" (356mm)

SINK

OUTLINE

CUTTING

LINE

Certified to comply with ANSI A112.19.4.M

U.S. Patent No. 4,664,982

Other patents pending.

CAN/C.S.A. B-45

Observe local plumbing and building codes.

6-23/32"

(171mm)

6-23/32"

(171mm)

7-25/32"

(198mm)

11-9/32"

(287mm)

5-21/32"

(144mm)

12-3/8"

(314mm)

14-1/2" Radius

(368mm)

14-1/2" Radius

(368mm)

15-9/16"(395mm)

16-1/2" (419mm)

CENTER LINE

OF BOWL

Summary of content (7 pages)

PAGE 1
™ Installation Instructions CHANDLER™ AMERICAST™ ISLAND SINK WITH FAUCET HOLES 7182.001/7182.803 WITHOUT FAUCET HOLES 7182.000 Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. Certified to comply with ANSI A112.19.4.M U.S. Patent No. 4,664,982 Other patents pending. CAN/C.S.A. B-45 Observe local plumbing and building codes. 791267-400 Rev.
PAGE 2
1 AFTER THE CUTOUT IS DRAWN... Drill a clearance hole inside the cutout line as marked on the countertop. 5 Perimeter of sink Apply a masking tape outline 1/8" outside traced outline as a guide for application of silicone sealant. Cutout Sink outline Masking 1/8" tape outline Cutout 2 Cut opening on cut line inside the perimeter of sink. 6 Perimeter of sink Cutout 3 Mount the faucet and drain assembly on the sink following the manufacturer's instructions.
PAGE 3
™ Installation Instructions AMERICAST ® BRAND SINKS UNDERCOUNTER MOUNTING FOR CHANDLER, LAKELAND, PALISADE AND SILHOUETTE™ KITCHEN SINKS MODELS 7145, 7162, 7163 STANDARD, 7103, 7172, 7173, 7179, 7182, 7183, 7185, 7196, 7255 Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. Certified to comply with ANSI A112.19.4.M U.S. Patent No.
PAGE 4
IMPORTANT: DIMENSIONS OF FIXTURES ARE NOMINAL AND MAY VARY WITHIN THE RANGE OF TOLERANCESESTABLISHED BY A.N.S.I. AND C.S.A. STANDARDS. SUPPORT CLIP LOCATIONS: 1054mm (41-1/2) 838mm (33) SUPPORT CLIPS 559mm (22) 559mm (22) SUPPORT CLIPS MODEL 7183 MODEL 7145, 7163 STANDARD,7179 914mm (36) 965mm (38) 559mm (22) 559mm (22) SUPPORT CLIPS MODEL 7196 SUPPORT CLIPS MODEL 7255 419mm (16-1/2) 457mm (18) SUPPORT CLIPS 457mm (18) SUPPORT CLIPS 381mm (15) MODEL 7185 MODEL 7182.
PAGE 5
NOTE 5 The following instructions are for countertop mounted fittings only. (Silhouette single bowl shown) Apply a bead of sealant to the edge of the sink. Hold the sink against the under-side of the countertop and rotate the clips to hold the sink in place. Snug the screws to hold the sink. Attach all the additional clips. 1 Countertop Drill a clearance hole inside the cutout line.
PAGE 6
INSTALLATION B — FITTINGS MOUNTED DIRECTLY ON SINK Refer to American Standard roughing-in information for specific dimensions for each model. Below are the dimensions of each sink. Make sure this area is available to mount the sink. Unfold the template and refer to the instructions below. CAUTION 1. Minimum countertop thickness is 19mm (3/4) for wood and 12mm (1/2") for marble and solid surface materials. SINK CUTOUTS: Locate and mark center lines of sink on countertop.
PAGE 7
NOTE 4 The following instructions are for mounting fittings directly to the sink. (Silhouette single bowl shown) 1 Countertop Drill a clearance hole inside the cutout line. Template Apply a bead of sealant to the edge of the sink. Hold the sink against the under-side of the countertop and rotate the clips to hold the sink in place. Snug the screws to hold the sink. Attach all the additional clips.