Two-Piece Toilet Installation Instructions Care And Maintenance

C L
TO RAISE
WATER
LEVEL
FLAPPER
ASSEMBLY
TO LOWER
WATER
LEVEL
TRIP
LEVER
FLUSH
VALVE
WATER
INLET
OVERFLOW
TUBE
FIG. 10A
WATER
LINE
LEVEL
+
WATER
CONTROL
ASSEMBLY
-
FLOW RATE
ADJUSTMENT
REFILL
TUBE
LIFT
ROD
FLOAT
BALL
RECOMMENDED TOOLS AND MATERIALS
Putty Knife Regular Screwdriver Adjustable Wrench Wax Ring/Gasket Flexible Supply Tube Tape Measure
Closet Bolts Hacksaw Sealant Carpenters Level Seat
1 REMOVE OLD TOILET
a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and level before new toilet is installed!
SAVE FOR FUTURE USE
3
2
ROUGHING-IN DIMENSIONS:
NOTE: Distance from wall to closet flange centerline
must be as listed below:
For 120012 Tanks: Rough-in distance is 305mm (12")
7301311-100 Rev.A
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
NOTE: Pictures may not exactly define contour of china and components.
!
ChinaLux 1000 EL
ChinaLux 1000 RF
POSITION TOILET ON FLANGE
a. Unplug floor waste opening and install toilet on
closet flange so bolts project through
mounting holes.
b. Loosely install retainer washers and nuts. Side of
washers marked “THIS SIDE UP” must face up!
a. Position toilet squarely to wall and, with a rocking
motion, press bowl down fully on wax ring and flange.
Alternately tighten nuts until toilet is firmly seated
on floor.
CAUTION:
DO NOT OVERTIGHTEN NUTS
OR BASE MAY BE DAMAGED!
b. Install caps on washers. (If necessary, cut bolt height
to size before installing caps.)
c. Smooth off the bead of sealant around base.
Remove excess sealant.
a. Install large rubber gasket over threaded
outlet on bottom of tank and lower tank
onto bowl so that tapered end of gasket
fits evenly into bowl water inlet opening.
b. Insert tank mounting bolts and rubber
washers from inside tank, through
mounting holes and gasket, and secure
with metal washers and nuts.
c. With tank parallel to wall, alternately
tighten nuts until tank is
snugged down evenly
against bowl surface.
INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer’s directions.
CLOSET
BOLT
NUT
TAPERED
WASHER
!
INSTALL WAX SEAL
Invert toilet on floor (cushion to prevent damage),
and install wax ring evenly around waste flange
(horn), with tapered end of ring facing toilet. Apply
a thin bead of sealant around base flange.
!
CAUTION:
DO NOT OVERTIGHTEN NUTS MORE
THAN REQUIRED FOR A SNUG FIT!
TANK MTG.
BOLTS
NUT
WASHER
RUBBER
GASKET
RUBBER
WASHER
ADJUSTMENTS
a. Flush tank and check that
tank fills and shuts off within
30 to 60 seconds, and tank
water level is set as
specified on tank rear wall.
b. To adjust water level:
turn water level adjustment
screw counterclockwise to
raise level; turn adjustment
screw clockwise to lower level.
c. To adjust flow rate (tank fill time):
turn flow rate adjustment screw
clockwise to decrease flow rate (increase fill time); turn adjustment screw
counterclockwise to increase flow rate (decrease fill time).
d. Carefully position tank cover on tank.
e. The flush valve float has been factory set and does not require adjustments.
Repositioning of the float will change the amount of water used which may
effect the toilet's performance.
f. If bowl fails to siphon, an adjustment may be required with the lift chain. Simply
remove the chain from the retainment clip (see Fig. 10) and take up slack on
the chain, and reinsert on lift rod. Make sure the chain is not too taught.
a. Connect water supply line
between shutoff valve and
tank water inlet fitting. Tighten
COUPLING NUT 1/4 turn
beyond hand tight. Check
that refill tube is inserted into
overflow tube.
b. Turn on supply valve and
allow tank to fill until float
rises to shutoff position.
c. Check for leakage at fittings,
tighten or correct as needed.
d. Do not use plumber's putty to
seal these fittings.
TANK
COUPLING NUT
FLEXIBLE
SUPPLY
WATER INLET
COMPRESSION
COLLAR
WASHER
VALVE NUT
TRIM PLATE
VALVE
CAUTION:
Overtightening of
COUPLING NUT could
result in breakage and
potential flooding.
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90°, and slide into
place 6" (152 mm) apart and parallel to wall.
INSTALLATION INSTRUCTIONS
CARE AND MAINTENANCE
To ensure this product is installed properly, please read these instructions carefully before you begin.
Certain installations may require professional help.) Also be sure your installation conforms to local codes.
BOLT
CAP
10
9
8
7
6
5
4
CONNECT WATER SUPPLY
INSTALL TANK
INSTALL TOILET