Bidet Faucet And Transfer Valve Installation Instructions

ManualsBrandsAmerican Standard ManualsIndoor FurnishingColony/Colony Soft 3475.300

3475.300

3475.500

COLONY/COLONY SOFT

Certified to comply with ANSI A112.18.1

Installation

Instructions

Bidet Faucet and Transfer Valve

with SpeedConnect™ Drain

Congratulations on purchasing your American

Standard faucet with Speed Connect drain, a

feature found only on American Standard faucets.

*Your new American Standard faucet is designed to work only with the SpeedConnect drain.

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

M968795Rev.1.1

Turn off hot and cold water

supplies before beginning.

CAUTION

BIDET FAUCET INSTALLATION

Replace UPPER GASKET (8) and WASHER (7) and

ESCUTCHEON (6) until it locks against internal stop.

Position the side threaded outlet rearward and

secure MOUNTING NUT (11).

Remove ESCUTCHEON (6), WASHER (7) and

UPPER GASKET (8) from TRANSFER VALVE (9).

Insert TRANSFER VALVE (9) into the center forward

hole of BIDET.

COLD

HOT

BIDET

LEDGE

SPRAY INSTALLATION

Assemble SPRAY BODY (1) to BIDET. Using putty, seal underside

of SPRAY BODY FLANGE (2) and secure with NUT (3).

Thread SPRAY CAP (9) onto SPRAY BODY (1).

Thread SPRAY HOSE (4) with SEAL WASHER (5) to SPRAY BODY (1).

Connect other end of HOSE (4) with SEAL WASHER (6) to side outlet

NIPPLE (7) of the TRANSFER VALVE (8).

PUTTY

Tighten LOCKNUTS (1) with WRENCH (5) (supplied)

to secure VALVE BODIES (3, 3a).

Install LOCKNUT (1) and RUBBER WASHER (2) onto VALVE BODIES (3, 3a). From

under side of mounting surface, install VALVE BODY (3, 3a) through valve mounting

holes. Threads of VALVE BODY (3, 3a) should extent at least 5/16 of a inch above

mounting surface top. Fig. A. Thread ESCUTCHEON (4) onto VALVE BODIES (3, 3a)

until snug against internal stop. If necessary, adjust LOCKNUT (1).

Place RUBBER RING (10) into ESCUTCHEON (4).

MOUNTING

SURFACE

3, 3a

5/16''

MIN.

Fig. A.

Adjustable Wrench

Screwdriver

Channel Locks

Required tools

Tubing Cutter

Phillips Screwdriver

Plumbers' Putty or

Caulking

Roughing-in

Dimensions

BIDET OUTLINE

IS SYMBOLIC

FINISHED

FLOOR

FINISHED

WALL

1-1/4 O.D. TAILPIECE

DOUCHE

SPRAY

2-1/8

DIA.

ADJ. 1-1/4

TO 2-1/4

3-7/8

5-1/2

1-3/8

DIA.

7/8 DIA.

1-1/4

MAX.

1-3/16

DIA.

2-1/4

DIA.

(C)

(H)

4-1/4

FOR GROUND JOINT

CONNECTION OR 1/2 "

O.D. SLIP (INLETS)

REAR VIEW WITH

WALL REMOVED

TRANSFER VALVE

(FOR FLUSHING

RIM OR SPRAY)

8 TO 12

SpeedConnect Drain*

• Fewer parts, installs in less time

• Never needs adjustment

• Guaranteed to seal properly the first time, every time.

Summary of content (6 pages)

PAGE 1
Installation Instructions 3475.300 3475.500 COLONY/COLONY SOFT Bidet Faucet and Transfer Valve with SpeedConnect™ Drain Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard faucets. Certified to comply with ANSI A112.18.1 SpeedConnect Drain* M 9 6 8 7 9 5 R e v. 1 . 1 • Fewer parts, installs in less time • Never needs adjustment • Guaranteed to seal properly the first time, every time.
PAGE 2
3 POP-UP DRAIN Fig. A. Remove CLEAR PLASTIC COVER (1). Fig. B. DRAIN BODY 1 Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). 3 Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 7 2 4 REMOVE FLANGE Fig. A. Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Fig. B. 1 Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B.
PAGE 3
8 ATTACH CABLE CONNECTOR Fig. A. POP-UP KNOB (1) must be fully down. Fig. A. Fig. B. Fig. C. DOWN 1 Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. B. Your new POP-UP DRAIN installation is now complete. Fig. C. 2 1-1/4” O.D. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. C. 9 CHECK OPERATION OF POP-UP 5 4 Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes.
PAGE 4
INSTALL HANDLES (Lever) INSTALL HANDLES (Acrylic) Turn HANDLE STEM (1) to "OFF" position. Turn HANDLE STEM (1) to "OFF" position. Place the HANDLE ADAPTER (2) on the HANDLE STEM (1). Place the ACRYLIC HANDLE (2) on the HANDLE STEM (1). Install the ADAPTER SCREW (3) and tighten securely. Position LEVER HANDLE (4) and place on ADAPTER (2). Install the HANDLE SCREW (5) and tighten securely with hex wrench supplied. 12 5 4 Install the HANDLE SCREW (3) and tighten securely. 3 Push in INDEX BUTTON (4).
PAGE 5
SpeedConnect™ Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
PAGE 6
STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front.