Colony FitRight Two-Piece Toilet Installation Instructions Care and Maintenance

ManualsBrandsAmerican Standard ManualsIndoor FurnishingColony FitRight Two-Piece Toilet 3510

RECOMMENDED TOOLS AND MATERIALS

Putty Knife Regular Screwdriver Adjustable Wrench Sealant Tape Measure

Hacksaw Wax Ring/Gasket Flexible Supply Tube Closet Bolts Carpenters Level

1 REMOVE OLD TOILET

a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.

b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!

c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.

d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.

NOTE: Mounting surface must be clean and level before new toilet is installed!

INSTALL CLOSET BOLTS

Install closet bolts in flange channel and slide

into place parallel to wall.

SAVE FOR FUTURE USE

CLOSET FLANGE

CLOSET BOLTS

7301152-100 Rev. F

CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

Product names listed herein are trademarks of AS America Inc.

NOTE: Pictures may not exactly define contour of china and components.

ROUGHING-IN DIMENSIONS:

NOTE: Distance from wall to closet

flange centerline must be as listed:

FINISHED WALL

FINISHED

FLOOR

SUPPLY

REQ'D.

WAX RING

SEALANT

INSTALL WAX SEAL

Invert toilet on floor (cushion to prevent damage), and

install wax ring evenly around waste flange (horn), with

tapered end of ring facing toilet. Apply a thin bead of

sealant around toilet base.

POSITION TOILET ON FLANGE

a. Unplug floor waste opening and install toilet on closet flange so bolts project

through mounting holes.

b. Loosely install retainer washers and nuts. Side of washers marked "THIS

SIDE UP" must face up!

CLOSET

BOLT

NUT

TAPERED

WASHER

FLANGE

Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is

installed properly, please read these instructions carefully before you begin. (Certain installations may require professional

help.) Also be sure your installation conforms to local codes.

Models 2435 / 2436 / 2437 / 2453 / 2485 / 2486 / 2487 / 3510

Colony FitRight Two-Piece Toilet

INSTALLATION INSTRUCTIONS

CARE AND MAINTENANCE

MODELS DIMENSION “A”

12"

(305mm)

10"

(254mm)

2453

3510

2435

2436

2437

24872485

2486

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS CARE AND MAINTENANCE Colony FitRight Two-Piece Toilet Models 2435 / 2436 / 2437 / 2453 / 2485 / 2486 / 2487 / 3510 Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes. ! CAUTION: PRODUCT IS FRAGILE.
PAGE 2
6 7 RUBBER WASHER TANK MTG. BOLTS RUBBER GASKET BOLT CAP WASHER NUT CLOSET FLANGE INSTALL TANK a. Install large rubber gasket over threaded outlet on bottom of tank and lower tank onto bowl so that tapered end of gasket fits evenly into bowl water inlet opening. b. Insert tank mounting bolts and rubber washers from inside tank, through mounting holes, and secure with metal washers and nuts. c. With tank parallel to wall, alternately tighten nuts until tank is snugged down evenly against bowl surface.
PAGE 3
10 11 ADJUSTMENTS TANK LEVER a. Adjust water level. Water level should be adjusted to level indicated on tank by adjusting float cup. REFILL TUBE HOOK TAB See Step 11 for water level adjustment method. FILL VALVE FLOAT CUP b. If bowl fails to siphon, an adjustment may be required with the lift chain. Simply remove the chain from the retainment clip and take up slack on the chain, and reinsert on lift rod. Make sure the chain is not too taught. FLUSH VALVE FLAPPER FLOAT CUP Turn on water supply.
PAGE 4
NOTE: Pictures are representative and may not exactly depict the flush valve. 13 TROUBLESHOOTING IF FILL VALVE SHUTS OFF BUT CONTINUES TO LEAK SLOWLY, repeat Step 13. IF FILL VALVE TURNS OFF AND ON DURING PERIODS OF NON-USE, it is a signal you are wasting water because: • The end of the refill tube is inserted into overflow pipe, below water level in tank. Attach refill tube to overflow pipe using "S" clip provided.