Deck-Mount Bath Filler Installation Instructions

ManualsBrandsAmerican Standard ManualsIndoor FurnishingEnfield 2373.920

*Wrench

Certified to comply with ANSI A112.18.1M

Required Tools

*Supplied with Fitting

*Hex key

Adjustable Wrench

Channel Locks

Flat Blade Screwdriver

DECK-MOUNT BATH FILLER

ENFIELD

MOUNTING

SURFACE

ADJ. 6-1/2 TO 12

3-3/4"

5-3/16"

1-1/2 MAX.

1-1/4

MAX.

1-3/16 DIA.

(H)

(C)

1-1/8 DIA.

8-3/16

12 MAX

2-1/16

DIA.

1-1/16 DIA.

3/4-14 MALE

N.P.T. INLETS

2-7/8"

LEVER

HANDLE

CROSS

HANDLE

2-1/4

DIA.

2-7/8

DIA.

M968288 Rev. 1.1

2373.900

2373.920

2373.901

2373.921

Installation

Instructions

ROUGHING-IN DIMENSIONS

with EverClean™ Finish

Congratulations on purchasing your American

Standard faucet with EverClean finish found

only on American Standard faucets.

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

EverClean Finish

• One wipe effortlessly removes spots

• Eliminates the need for cleaners and scrubbing

• Permanent surface protectant remains beautiful

for the life of the faucet

• EverClean™ available on: Polished Chrome, Satin Nickel,

Stainless Steel, Polished Brass (or any combination of these finishes)

IMPORTANT NOTICE TO INSTALLER!

Please check with local Code Authority for the installation requirements of this product. Some codes require an

additional temperature mixing valve to limit the maximum hot water temperature and vacuum breaker

(for products with hand spray) to be installed with this product.

Summary of content (4 pages)

PAGE 1
Installation Instructions ENFIELD 2373.900 DECK-MOUNT BATH FILLER 2373.920 with EverClean™ Finish 2373.901 Congratulations on purchasing your American 2373.921 Standard faucet with EverClean finish found only on American Standard faucets. EverClean Finish • One wipe effortlessly removes spots Certified to comply with ANSI A112.18.1M • Eliminates the need for cleaners and scrubbing M 9 6 8 2 8 8 R e v. 1 .
PAGE 2
1 2 SPOUT ASSEMBLY Turn off hot and cold water supplies before beginning. CAUTION PREPARE TUBE AND TEE ASSEMBLY Prepare TUBE and TEE ASSEMBLY (1) to fit center to center VALVE (2) location (between 6-1/2" and 12"). If necessary, cut and/or bend TUBING carefully. Make sure tube bend is close to the TEE (1) so that it will not effect the compression joint at the VALVE CONNECTION. Install RING WASHER (1) into SPOUT BASE recess. Check that O-RING (2) on end of SPOUT SHANK (3) is in place.
PAGE 3
4 INSTALL HANDLES Push ADAPTER (1) on VALVE STEM (2), so that the hole of the ADAPTER (1) without a spline is facing up. See figure "A". Tighten STEM SCREW (3) to secure ADAPTER (1). Find correct position of LEVER HANDLE ASSEMBLY (4) or CROSS HANDLE ASSEMBLY (5) by adjusting male teeth on ADAPTER (1) to female teeth in HANDLE (4, 5). 4 THREAD ON TO DECK ADAPTER 5 Thread LEVER HANDLE ASSEMBLY (4) or CROSS HANDE ASSEMBLY (5) onto DECK ADAPTER (6) until snug against mounting surface.
PAGE 4
7 CAUTION TEST INSTALLED FAUCET The flow rate of this Tub Filler exceeds 20 gallons/minute at higher water pressure. Do not fill bathtub unattended. Turn VALVES (1) to "off" position. With handles in "off" position, turn on water supplies and check all connections for leaks. 1 4 1 Operate both handles and flush water lines thoroughly. Check SPOUT (2) mounting for leaks. 3 Lift HAND SHOWER (3) from holder, direct spray into tub, lift TRANSFER KNOB (4) to check HAND SHOWER (3) and HOSES for leaks.