Enfield Console Table Assembly and Installation Instructions

ManualsBrandsAmerican Standard ManualsIndoor FurnishingEnfield Console Table 7460.200

752877-100 REV. A

Product names listed herein are trademarks of American Standard Inc.

ASSEMBLY & INSTALLATION

INSTRUCTIONS

Enfield Console Table

7460.100 With Raised Wood Panels

7460.200 With Cast Grilles

- 1 -

Recommended Tools & Materials

Roughing-in Dimensions

Thank you for selecting our products...products which have been the benchmarks of fine quality for over 100 years.

To help insure that the installation process will proceed smoothly, please read these instructions carefully before you

begin. Also, review the recommended tools and materials list; carefully unpack and examine your new plumbing fixture.

Adjustable Wrench

Channel Locks

Phillips Screwdriver

Putty Knife

Regular Screwdriver

Drill

Saber Saw

Level

Basin Wrench

Plumbers' Putty or

Caulking

Tubing Cutter

10'

Tape

Measure

Hacksaw

Pipe Wrench

™

To maintain the beauty of the finish, avoid placing the furniture in direct sunlight, as sunlight causes fading. Also avoid

extreme changes in temperature by arranging furniture away from radiators, heat and air vents, and air conditioning units.

Avoid placing furniture directly under windows.

7460.100

7460.200

6860.725 Bakersfield White or

6860.722 Autumn Spray

0740 Enfield

CONSOLE TABLE VANITY TOP-GRANITE RECOMMENDED SINK

25-1/4

(641mm)

8" *

(203mm)

4" *

(102mm)

14-1/8

(359mm)

16-1/4

(413mm)

(737mm)

LEG ANCHORING

SCREW HOLES

5/16 (8mm) DIA.

(TYP. 4 PLACES)

22 REF.

(559mm)

(864mm)

1-1/4

(32mm)

6-1/4

(159mm)

12-3/4

(324mm)

12-1/4

(811mm)

11-1/4

(286mm)

(178mm)

FINISHED

FLOOR

(203mm)

25-3/4 REF.

(654mm)

1-1/4 O.D.

WASTE

1-1/4 O.D.

TAILPIECE

SUPPLIES

AS REQ'D

SEALING

COMPOUND

1-1/8" (30mm) THK.

GRANITE SURFACE

SATIN SWALLTAIL

LAPPER

CAST METAL

DESIGN INSERT

PANELED INSERT

of Faucet **

Summary of content (4 pages)

PAGE 1
™ ASSEMBLY & INSTALLATION INSTRUCTIONS Enfield Console Table 7460.100 With Raised Wood Panels 7460.200 With Cast Grilles CONSOLE TABLE VANITY TOP-GRANITE 7460.100 7460.200 6860.725 Bakersfield White or 6860.722 Autumn Spray RECOMMENDED SINK 0740 Enfield Thank you for selecting our products...products which have been the benchmarks of fine quality for over 100 years. To help insure that the installation process will proceed smoothly, please read these instructions carefully before you begin.
PAGE 2
CONSOLE TABLE INSTALLATION Identify desired location of the console table. Provide suitable reinforcement required for anchoring the vanity to the wall. Centerline of reinforcement should be 30" up from the floor (see Figure 1). Rough in supply lines and waste per rough in dimensions. Drill at least two 3/8" O.D. anchoring holes through the rear stringer of the console table at 2-1/2" down from the top of the table (see Figure 2).
PAGE 3
Mount the drain assembly to the sink. Be certain to apply a bead of sealing putty on the underside of the drain (area "A") in order to ensure a watertight seal between the sink and drain. Remove excess putty. Install the sink on the granite top using sealant. Add or remove excess compound around the base of sink rim. Form fillet the sealant with wet finger or sponge. SEALANT A After installing the sink, connect the trap to the drain assembly and hand tighten to check alignment.
PAGE 4
REPAIR PARTS 730679-0070A Adjustable Threaded Foot Glide (4 per pack) 752686-3300A Cherry Wood Panel Kit (2 side and 1 front panel and screws) 752686-3340A Maplewood Panel Kit (2 side and 1 front panel and screws) 752679-0070A Cast Grille Kit (2 side and 1 front grille and screws) AMERICAN-STANDARD GRANITE/MARBLE TABLE TOP WARRANTY If inspection of this American-Standard plumbing product, within one year after its initial purchase, confirms that it is defective in materials or workmanship, American-