Centerset Lavatory Faucet Installation Instructions

ManualsBrandsAmerican Standard ManualsIndoor FurnishingJasmine Amarilis 3808.101

51314 Rev.1.3

Certiﬁed to comply with ANSI A112.18.1

Installation

Instructions

Centerset Lavatory Faucet with

Speed Connect™ Drain

Adjustable Wrench Screwdriver Channel Locks

Recommended tools

INSTALL FAUCET

Fig. B.

Fig. A.

3808.101

INSTALLATION WITH

ESCUTCHEON PLATE

SINGLE HOLE

INSTALLATION

For single hole installation. Fig. A.

Make sure that O-RING (1) is installed into base of FAUCET (2).

For installation with DECORATIVE RING (3) (single hole installation) feed faucet

SUPPLIES (4) and CABLE CONNECTOR (5) through sink or mounting surface hole.

For installation with ESCUTCHEON PLATE (6) (for 3 hole, 4" centers installation)

use the following steps:

Fig. B.

From below, push GASKET (7) and RETAINER PLATE (8)

over STUD (9) and secure with NUT (10) Before ﬁnal

tightening, adjust faucet so that it is centered over

mounting hole.

Feed faucet tubes through O-RING (1) supplied with

ESCUTCHEON PLATE (6) and through the hole in the

ESCUTCHEON (6) and through SINK or DECK.

Unscrew and remove DECORATIVE RING (3) from FAUCET BODY (2).

Apply putty to underside of ESCUTCHEON PLATE (6) and

place over mounting holes.

PUTTY

Congratulations on purchasing your American Standard

faucet with Speed Connect drain, a feature found only on

American Standard faucets.

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

Speed Connect™ Drain*

• Fewer parts, installs in less time

• Never needs adjustment

• Guaranteed to seal properly the first time, every time.

Turn off water at

main supply.

CAUTION

Summary of content (4 pages)

PAGE 1
Installation Instructions 3808.101 Centerset Lavatory Faucet with Speed Connect™ Drain Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard faucets. Certified to comply with ANSI A112.18.1 Speed Connect™ Drain* 51314 Rev.1.3 • Fewer parts, installs in less time • Never needs adjustment • Guaranteed to seal properly the first time, every time.
PAGE 2
POP-UP DRAIN Fig. A. Remove CLEAR PLASTIC COVER (1). Fig. B. 1 Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). DRAIN BODY 3 Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 2 3 REMOVE FLANGE 4 Fig. A. Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Fig. B. 1 Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B.
PAGE 3
7 ATTACH CABLE CONNECTOR Fig. A. Fig. B. Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. 1 Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. 2 1-1/4” O.D. 8 CHECK OPERATION OF POP-UP 1 Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions.
PAGE 4
10 TEST INSTALLED FITTING With HANDLE (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. 4 1 Remove AERATOR (3). Operate HANDLE (1) to flush water lines thoroughly. Replace AERATOR (3). CHECK DRAIN CONNECTIONS 3 Operate POP-UP KNOB (4) and fill lavatory with water. Check that DRAIN STOPPER (5) makes a good seal and retains water in SINK. If DRAIN STOPPER (5) does not seal properly, please refer to Troubleshooting section in these instructions.