INSTALLATION INSTRUCTIONS Passage™ Shower Bases MODELS: A8011T-RHO, A8011T-LHO Visit http://www.americanstandard-us.com/passage-collection for coordinating products. Thank you for selecting American Standard...the benchmark of fine quality for over 140 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. Local building codes vary by location. Observe all local plumbing and building codes.
1 Ensure that the floor and stud walls are square and plumb on a level floor as shown in Figure A. Provide a 5" x 5" (127 x127 mm) opening in the floor for the drain and refer to the product rough-in for actual drain location. Draw a line 3-1/4" (82 mm) above the level subfloor on the wall studs at each side of the opening.
Mix a non-shrinking bedding material such as mortar and apply enough bedding material to support the entire bottom of the shower base. Concrete is NOT recommended. The shower base is NOT to be supported by the base flange.
POST INSTALLATION CLEAN-UP Remove all construction debris. Tile grout can be removed with a wooden popsicle stick or tongue depressor. Do not use wire brushes or any other metal implement on bath surface. Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent. Stubborn dirt or stains may be removed using granular Spic and Span® mixed with water. Painter’s naphtha can be used to remove excess adhesives and/or wet oil-base paint.
INSTALLATION INSTRUCTIONS PASSAGE™ 60" x 72" FRAMELESS SHOWER DOOR MODEL: AM801703400 SERIES Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. Certain installations may require professional help. Also be sure your installation conforms to local codes. Visit http://www.americanstandard-us.com/passage-collection for coordinating products.
BOX CONTENTS [1] 1x Horizontal Rail INSTALLATION INSTRUCTIONS 1 Installation Instructions PASSAGE™ 60x72 FRAMELESS SHOWER DOOR MODEL: AM801703400 SERIES Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.
ASSEMBLY DRAWING [12] [15] [33] [9] [11a] [8] [10] [1] [11b] [13] [14] [16] [22] [24] [20] [21] [19] [31] [23] [32] [2] [25] [17] [27] [28] [5] [26] [3] [7] [6] [29] [4] [30] [1] 1x Horizontal Rail [2] 1x Door Handle [3] 1x Screws M4x35 [4] 1x Wall Anchor [5] 1x Screw Cover Cap [6] 1x Bottom Guide [7] 1x Shim [8] 2x Rollers [9] 2x Fixed Panel Fasteners [10] 2x Door Panel Guards [11] 2x Wall Connectors [12] 2x Connector Base Mounts [13] 2x Cushions [14] 4x Wall Anchors [15] 4x Screws
1 In Step 1, we will cover attaching the connector base mounts and the wall posts for the stationary glass door panel. This will require parts 11, 12, 13, 14, 15, 21, 22, 23 and 24. NOTE: The Passage Shower Door can be installed with the fixed door panel on the left or right hand side. The illustrations below show the door assembled with the handle on the right side of the shower.
2 In Step 2, we will cover installing the floor U Channel and Bottom Guide. This will require parts 3, 4, 5, 6, 7, 21, 23, 28, 31 and 32. 2a. Place U Channel [28] and Bottom Guide [6] on the Fixed Wall Post [21] side on the edge of the shower base threshold. NOTE: The smaller side of the Bottom Guide is meant to hold the Fixed Panel [31] (with the rubber Shim [7]), while the larger side is meant to hold the sliding Door Panel [32] (without rubber Shim [7] ).
3 ! In Step 3, we will cover the assembly and installation of the fixed door panel. This will require parts 6, 7, 17, 21, 22, 23, 24, 27, 28 and 31. NOTE: Product is heavy and REQUIRES TWO PEOPLE for installation. 3a. Ensure clear Shim [7] is in groove on Bottom Guide [6] for Fixed Panel side. NOTE: Place a minimum of 2 clear channel shims in bottom of U channel. Clear channel shims Clear channel shims 3a [7] 3b 3b.
5 In Step 5, we will cover the installation of the horizontal rails and wall connectors. This will require parts 1, 9, 11a, 12, 31 and 33. [11a] 5a. Screw Limit Block [33] to Wall Connector [11a]. 5a [33] NOTE: Wall Connector [11a] has a threaded hole on one side to accommodate the Limit Block. [11a] 5b. Attach Wall Connector with Limit Block to Connector Base Mount [12] on the Fixed Panel [31] side of shower and tighten 2 allen screws using supplied hex allen key. 5b 5c.
6 In Step 6, we will cover assembling the rollers and sliding glass panel door. This will require parts 2, 8, 18 and 32. 6a. Separate door handles [2] by removing brass connector with threaded stem from handles. Place the round bushing and clear square gasket over the threaded stem and onto the Sliding Door Panel [32] keeping clear washers between the glass panel. Then place the other handle over brass connector. 6a [2] 6b 6b. Tighten allen screws to secure Door Handle in place. 6c.
7 ! In Step 7, we will cover attaching the sliding glass door panel to the horizontal rail. This will require parts 1, 6, 8, 10, 16, 19, 20, 21 and 32. NOTE: Product is heavy and REQUIRES TWO PEOPLE for installation. [8] 7a. Carefully place Sliding Door Panel [32] onto Horizontal Rail [1] from inside of shower area and onto the Rollers [8]. 7a [6] 7b. Ensure bottom of Sliding Door Panel [32] onto Horizontal Rail [1] from inside of shower area and onto the Rollers [8]. 7c.
8 In Step 8, we will cover adjusting the Sliding Door Panel [32]. 8a. Once all assembly is completed, it may be necessary to adjust the Sliding Door Panel [32] for proper operation. This can be achieved by adjusting Rollers [8] attached to the Sliding Door Panel [32] by loosening the metal nut on the Roller. 8a [8] [8] MAX MIN 8b.
10 In Step 10, we will cover attaching the hardware to the Sliding Wall Post. This will require parts 20, 21 and 26. 10a. Three hole locations are predrilled into the Post [20] and can be used to mark drill locations in the Sliding Wall Post [21] from the inside of shower. Remove Post and drill marked locations using a 1/8" (3.2mm) drill bit. 10b. Place Post [20] back onto Sliding Wall Post [21} and use 3 supplied M4x8 screws, placing white plastic cups through each screw to hold Screw Cover Caps [26].
MAINTENANCE: Two primary materials are used to manufacture your new American Standard shower enclosure: tempered glass and anodized aluminum. To assure a long lasting finish on the enclosure, wipe it down with a towel after each use. For occasional, more concentrated cleaning efforts Lysol Non-Abrasive Bathroom Cleaner works extremely well. Be sure that any over spray falling on the aluminum frame is rinsed thoroughly and dried.
INSTALLATION INSTRUCTIONS PASSAGE™ CUSTOM SHOWER WALL SYSTEM MODELS: P2971SWT, P2974BWT Visit http://www.americanstandard-us.com/passage-collection for coordinating products. Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes. BEFORE YOU BEGIN....
1 DRY FITTING THE TONGUE AND GROOVE PANELS ON THE WALL 1) Dry fit the panels starting with the rear most panels first. Keep a 1/8" (5mm) gap above the tub deck or shower base for all panels. When connecting several panels together, panels use a tongue and groove system to connect to each other. See Illustration 2. NOTE: The use of suction cups will aid in the handling and installation of the shower wall panels. Illustration 2 TONGUE AND GROOVE ASSEMBLY 2) Dry fit the 2 side panels next.
3) With the aid of suction cups, move first rear panel onto the wall keeping a space of approximately 1/8" (5mm) off the surface of the tub deck or shower base. Press panel firmly over entire surface to ensure firm contact of panel to adhesive on wall. NOTE: It may be necessary to brace or support the panels against the wall until the panels stay securely in place. See illustration 6.
POST INSTALLATION CLEAN-UP Remove all construction debris. Tile grout can be removed with a wooden popsicle stick or tongue depressor. Do not use wire brushes or any other metal implement on surface. Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent. Stubborn dirt or stains may be removed using granular Spic and Span® mixed with water. Painter's naphtha can be used to remove excess adhesives and/or wet oil-base paint.
