Retrospect Console Table Assembly and Installation Instructions

ManualsBrandsAmerican Standard ManualsIndoor FurnishingRetrospect Console Table 7812.295

730757-100 REV. B

Product names listed herein are trademarks of American Standard Inc.

ASSEMBLY & INSTALLATION

INSTRUCTIONS

7812.002

7812.295

RETROSPECT® CONSOLE TABLE

- 1 -

Recommended Tools & Materials

Thank you for selecting our products...products which have been the benchmarks of fine quality for over 100 years.

To help insure that the installation process will proceed smoothly, please read these instructions carefully before you

begin. Also, review the recommended tools and materials list; carefully unpack and examine your new plumbing fixture.

Adjustable Wrench

Channel Locks

Regular Screwdriver

Phillips Screwdriver

Pipe Wrench

Putty Knife

Drill

Level

Plumbers' Putty or

Caulking

Tape

Measure

Hacksaw

0282.008 RETROSPECT® CONSOLE PEDESTAL TOP

8711.000.002 CONSOLE TABLE LEGS (Chrome)

8711.000.295 CONSOLE TABLE LEGS (Satin)

1-1/4 O.D.

WASTE

SUPPLIES

AS REQ'D

FINISHED

FLOOR

FINISHED

WALL

3/8" (10mm) DIA.

SINK ANCHOR

SCREW HOLES

ON 13-3/4" (349mm)

CENTERS

36"

(914mm)

7-1/4"

(184mm)

8-1/8" TO

BOTTOM OF

DRAIN OUTLET

(206mm)

24"

(610mm)

22"

(559mm)

1-1/4" O.D.

TAILPIECE

(203mm)

FINISHED WALL

(229mm)

19-3/4"

(502mm)

27"

(686mm)

(203mm)

13-3/4"

(349mm)

3-3/8"

(86mm)

1-3/4" DIA.

STD. DRAIN

OUTLET

3 Holes

1-3/8" (35mm) Dia.

15"

(381mm)

7-1/2"

(191mm)

11"

(279mm)

Summary of content (4 pages)

PAGE 1
ASSEMBLY & INSTALLATION INSTRUCTIONS RETROSPECT® CONSOLE TABLE 7812.002 7812.295 Thank you for selecting our products...products which have been the benchmarks of fine quality for over 100 years. To help insure that the installation process will proceed smoothly, please read these instructions carefully before you begin. Also, review the recommended tools and materials list; carefully unpack and examine your new plumbing fixture. Recommended Tools & Materials 0282.008 8711.000.002 8711.000.
PAGE 2
1 2 #3 Place a middle leg tube (Item #4) over each threaded rod. Identify the shelf support pins at the inner corners of the Shelf Support (Item #5). Guide each threaded rod through the corners of the shelf support so that these support pins are nearer to you. #2 #1 Run the two front leg sub-assemblies (Item #1) through the two front holes of the towel bar (Item #2). Do the same with the two rear leg assemblies (Item #3).
PAGE 3
2 1) Move console table legs into approximate position near the wall. 2) Place sink on console, aligning the rubber grommets on the top of the front legs with the recesses in the underside of the front of the sink. 3) Place a level on the shelf support and use the four independently adjustable console feet to level the assembly both side-to-side and front-to-back. 4) Place the level on the sink and use the two independently adjustable trumpets on the tops of the rear legs to level the sink.
PAGE 4
8711 CONSOLE TABLE LEGS COMPONENTS LIST Note: "XXX" represents color or trim finish options. Specify when ordering. ITEM # A B C D E F G PART NO. 738728-XXX0A 738729-XXX0A 738730-0070A 738744-XXX0A 738743-XXX0A 738879-0070A 738739-0070A PACKED QTY. DESCRIPTION 1 Towel Bar 1 Shelf Support 1 Glass Shelf 1 Front Leg Assembly 1 Rear Leg Assembly 2 Front Leg Grommet Kit 4 Hex Nut Kit #238 F G For chrome, replace "XXX" with 002 when ordering. For satin, replace "XXX" with 295 when ordering.