Single Control Kitchen Faucet with Cast Spout Installation Instructions

ManualsBrandsAmerican Standard ManualsIndoor FurnishingSingle Control Kitchen Faucet with Cast Spout 3821.641 Series

SINGLE CONTROL KITCHEN

FAUCET WITH CAST SPOUT

Installation

Instructions

M968188E

Thank you for selecting American-Standard...the benchmark

of fine quality for over 100 years.

To ensure that your installation proceeds smoothly--please

read these instructions carefully before you begin.

Certified to comply with ANSI A112.18.1M

3821.631 SERIES

3821.641 SERIES

3821.634 SERIES

3821.644 SERIES

CAUTION

INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON

Turn off hot and cold water supplies before beginning.

PUTTY

SPOUT BASE

SINK OR

MOUNTING

SURFACE

Assemble RUBBER WASHER (5), BRASS WASHER (6), and threaded LOCKNUT (7) onto SHANK (4) from underside

of sink or mounting surface. Hand tighten LOCKNUT (7) and check that rotation of HANDLE (8) from HOT to COLD

is centered.

Push O-RINGS (2) onto SPOUT SHANK. Make certain the O-RING (2) is properly seated in recess of DECORATIVE

FLANGE (10).

Insert SUPPLY TUBES (3) and SHANK (4) through mounting hole and seat DECORATIVE FLANGE (10) onto sink or

mounting surface.

Use a screwdriver to tighten SCREWS (9) on LOCKNUT (7). Work your way around LOCKNUT (7), tightening

the screws slightly each time until all are snug to ensure even pressure.

(A) Installation with ESCUTCHEON (1).

Apply a bead of putty to bottom edge of ESCUTCHEON (1). Insert supply

TUBES (3) and SHANK (4) through hole of ESCUTCHEON (1) and mounting surface. Make certain the O-RING (2)

is properly seated in recess of SPOUT BASE. Follow mounting instructions below to secure faucet to mounting surface.

(B) Installation less ESCUTCHEON (1).

Remove ESCUTCHEON (1) , feed FAUCET TUBES (3) and SHANK (4) through

DECORATIVE FLANGE (10). Push FLANGE so the raised step fits into recess of SPOUT BASE.

Plumbers' Putty or Caulking

Adjustable Wrench

Phillips Screwdriver

Channel Locks

TOOLS REQUIRED

Tubing Cutter

Regular Screwdriver

Summary of content (4 pages)

PAGE 1
Installation Instructions SINGLE CONTROL KITCHEN FAUCET WITH CAST SPOUT 3821.631 SERIES 3821.641 SERIES 3821.634 SERIES 3821.644 SERIES Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.
PAGE 2
MAKE WATER SUPPLY CONNECTIONS NOTE: FLEXIBLE SUPPLIES HAVE TO BE PURCHASED SEPARATELY Carefully bend COPPER SUPPLIES to meet water supply lines using the palms of the hands to avoid kinking. Connect HOT water supply line to left tube, and COLD water supply line to right tube using appropriate connectors. Use 1/2" IPS FLEXIBLE SUPPLIES (3) or 3/8" O.D. BULL-NOSE RISERS (4). Use adjustable wrench to tighten connections. Do not over tighten. Be careful not to kink copper supply when bending.
PAGE 3
5 TEST INSTALLED FAUCET Move HANDLE down into "off" position and remove AERATOR. Turn on water supplies and check connections for leaks. Operate HANDLE up and down, left and right to flush water lines thoroughly. For faucet with spray, direct SPRAY HEAD into sink and activate SPRAY. Check hose connections for leaks. Move HANDLE down to "off" position and replace AERATOR. HANDLE SPRAY AERATOR CHECK CONNECTIONS FOR LEAKS 6 SERVICE Reduced flow.
PAGE 4
SINGLE CONTROL KITCHEN FAUCET WITH CAST SPOUT 023527-0070A CARTRIDGE SCREWS 060343-0070A SPACER WITH O-RINGS MODEL NUMBERS 023529-0070A CARTRIDGE 3821.631 SERIES 3821.641 SERIES 3821.634 SERIES 3821.