Installation Sheet

ManualsBrandsAmerican Standard ManualsBathContemporary Single-Handle Floor-Mount Roman Tub Faucet with Hand Shower for Flash Rough-In Valves in Brushed Nickel

Recommended Tools

Channel Locks

Tubing CutterFlat Blade Screwdriver

Phillips Screwdriver

Adjustable Wrench

Pipe Wrench

Teon Tape

Electric Drill

6mm

Hex wrench

5mm

Hex wrench

Level

ROUGHING-IN DIMENSIONS

T184.951

Certied to comply with ANSI A112.18.1

Installation

Instructions

Thank you for selecting American-Standard...

the benchmark of ﬁne quality for over 140 years.

To ensure that your installation proceeds smoothly--

please read these instructions carefully before you begin.

Contemporary Square

Floor Mounted Tub Filler

Round Bubble Level

M965959 Rev. 1.0 (9/20)

ESCUTCHEON

FINISHED

FLOOR

(177 mm)

10-3/8"

(264 mm)

4-3/4" x 4-3/4"

(120 x 120 mm)

3/4"

(20 mm)

*2" MIN.

(51 mm)

1-5/8"

(40 mm)

(102 mm)

1-13/16" x 1-13/16"

(46 x 46 mm)

46-3/4" MAX.

(1188 mm)

13˚

26-7/8" MAX.

(682 mm)

29-3/4" MAX.

(755 mm)

39-3/16" MAX.

(995 mm)

44-5/8" MAX.

(1134 mm)

3/4"

(19 mm)

IMPORTANT

NOTICE TO THE INSTALLER!

Please check with your local Code Authority

for acceptable installation requirements for

this Roman Tub set with hand shower. Some

local codes may require a vacuum breaker

and/or a pressure balanced mixing valve to

be installed in conjunction with this product.

*Adequate ﬂoor support is required.

The wood support must be a minimum

of 2" (51mm) thick by 10" (254mm) wide.

2x6 lumber is NOTadequate for

this application.

*WOOD SUPPORT

PLASTER GUARD

10" (254 mm) MIN.

FLOOR JOIST

2-3/4"

70 mm MIN.

1/2" NPT

FEMALE THREAD

COLD

1/2" NPT

FEMALE THREAD

HOT

4" DIA.

(103 mm)

LEVELING NUT

WASHER

LOCK WASHER

MOUNTING NUT

MOUNTING SCREW

Summary of content (6 pages)

PAGE 1
Installation Instructions Contemporary Square Floor Mounted Tub Filler T184.951 Thank you for selecting American-Standard... the benchmark of fine quality for over 140 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
PAGE 2
1 REMOVE EXPOSED PLASTER GUARD • Cut the exposed part of the PLASTER GUARD (1) flush with the finished floor. Be careful not to damage the floor. • Place GASKET (2) under BASE PLATE (3). 1 • Secure BASE PLATE (3) with SCREWS (4) to the PLASTER GUARD (1). 4 3 2 FINISHED FLOOR FRON T HOT COLD 2 REMOVE RETAINING PLATE AND SCREWS • Remove the SIX RETAINING PLATE SCREWS (2) with a (5 mm) hex wrench. 5mm HEX WRENCH • Remove RETAINING PLATE (3). 3 2 FINISHED FLOOR FRONT COLD HOT M965959 Rev. 1.
PAGE 3
REMOVE HOT AND COLD TEST PLUGS Note: Floor is not shown for clarity in this illustration. • Remove the two TEST PLUGS (4) with a (6 mm) hex wrench. 6 mm HEX WRENCH 4 M965959 Rev. 1.
PAGE 4
INSTALL TUB FILLER • Before final installation, check that all sealing surfaces are clean and that the INLET HOSE O-RINGS (5) are not damaged. Important: INLET HOSE O-RINGS (5) can be damaged if caution is not used when installing. 5 Match inlet hose marked with a blue dot with the hole on the manifold also marked with blue dot. (VIEW “A”) 6 (VIEW “A”) HOT COLD • Install the INLET HOSES (6) into the MANIFOLD MOUNTING BASE (7).
PAGE 5
4b INSTALL SPOUT AND HAND SHOWER • Align PIN (11) in FAUCET BASE (12) with HOLE (13) in SPOUT BASE (14). Install SPOUT (15) into FAUCET BASE (12). Tighten the two SET SCREWS (16). • Install SEALS (17) on both ends of the SPRAY HOSE (18). Connect the end with the hex to the DIVERTER (19) using an adjustable wrench. Hand tighten the connection to the HAND SHOWER (20). Note: When not in use, the HAND SHOWER (20) should be seated in the SHOWER HOLDER (21).
PAGE 6
Contemporary SQUARE Floor Mounted Tub Filler MODEL NUMBER T184.