Installation Guide

ManualsBrandsAmerican Standard ManualsPlumbingBerwick 2-Handle Thermostatic Valve Trim Kit with Separate Volume Control in Polished Chrome (Valve Not Included)

T430.740

T431.740

Installation

Instructions

M 9 6 5 0 0 3 R E V. 1.2 (1/15 )

Thank you for selecting American-Standard...the

benchmark of ﬁne quality for over 100 years.

To ensure that your installation proceeds smoothly--please

read these instructions carefully before you begin.

Certiﬁed to comply with ANSI A112.18.1

ASSE 1016

ROUGHING-IN DIMENSIONS

Recommended Tools

Flat Blade Screwdriver

Phillips Screwdriver

Remove as much surface dirt and ﬁlm using clear

water and soft cotton cloth (as described above).

Use any of the following to remove tough surface

ﬁlm and build-up:

Mild liquid detergents

Clear ammonia free liquid glass cleaners

Non-acidic, non-abrasive gentle liquid or fully

dissolved powder cleansers mixed according to

manufacturers directions.

Non-abrasive liquid polishers

Once clean, rinse faucet again with clear water to

thoroughly remove cleaner or polish and blot dry with

a soft cotton cloth.

To keep your new faucet looking new, please follow

these simple care instructions:

DO: Simply rinse the faucet clean with clear water.

Dry the faucet with a soft cotton cloth.

DO NOT:

Do not use any abrasive cleaners, cloths, or

paper towels.

Do not use any cleaning agents containing

acids, polish abrasives, or harsh cleaners or

soaps.

Regular and routine cleaning will reduce the need for

heavy cleaning and polishing. If heavy cleaning is

required, the following procedures are recommended:

CARE INSTRUCTIONS:

Failure to follow these care instructions may

damage the Faucet's ﬁnish.

CENTRAL THERMOSTAT

WITH VOLUME CONTROL

TRIM KIT

7-3/8"

(186mm)

3-7/8"

(100mm)

" TO 2-5/8"

(48mm TO 68mm)

NOTE: FITTING

MUST BE INSTALLED

WITH VOLUME CONTROL

ON TOP.

R520

1/2" NPT INLETS

R540

3/4" NPT INLETS

(25mm)

FINISHED

WALL

7-1/16"

(179mm)

7-15/16"

(202mm)

(152mm)

CROSS

HANDLE

LEVER

HANDLE

CROSS

HANDLE

LEVER

HANDLE

BERWICK

™

/ BOULEVARD

™

Summary of content (4 pages)

PAGE 1
Installation Instructions T430.740 T431.740 BERWICK ™ / BOULEVARD ™ CENTRAL THERMOSTAT WITH VOLUME CONTROL TRIM KIT Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1 ASSE 1016 M 9 6 5 0 0 3 R E V. 1.
PAGE 2
1 TRIM INSTALLATION Remove PLASTER GUARD (1) if attached. 2 Push CAPS (2 & 2a) as shown onto CONTROL VALVES (3). Push ESCUTCHEON HOLDER (4) with lightly greased O-RING SEALS (5) over CAPS (2, 2a). Attach with the two SCREWS (6) provided. TOP 4 1 3 Align pins in back of ESCUTCHEON (7) with holes in ESCUTCHEON HOLDER (4) and push ESCUTCHEON (7) into place. 5 PINS 2a 7 6 1 2 INSTALL HANDLES Thread HANDLE SCREW (1) into VALVE STEM (2) and tighten to secure KNOB MOUNT (3).
PAGE 3
4 TEMPERATURE ADJUSTMENT Loosen SET SCREW (1). Pull off HANDLE ASSEMBLY (2). Check that arrow marking B points to the 12 o'clock position. If not, push the BLACK CLAMP on the SECURING RING to the right, pull off KNOB MOUNT (3) and reinstall KNOB MOUNT (3) with arrow "B" 12 o'clock position. See Figure 1. SET HOT LIMIT STOP The maximum mixed water temperature is set at 109˚F at the factory. This setting can be changed if desired. Remove the TEMPERATURE LIMIT STOP (H shaped Red Plastic part).
PAGE 4
BERWICK ™ / BOULEVARD ™ CENTRAL THERMOSTAT WITH VOLUME CONTROL TRIM KIT MODEL NUMBER T430.740 / T431.