Installation Guide

ManualsBrandsAmerican Standard ManualsBathBerwick 2-Handle Deck-Mount Roman Tub Faucet for Flash Rough-in Valves in Polished Chrome

- 1 -

Product names listed herein are trademarks of AS America, Inc.

Thank you for selecting American Standard...

the benchmark of ﬁne quality for over 140 years.

To ensure that your installation proceeds smoothly-please read

these instructions carefully before you begin.

RECOMMENDED TOOLS

ROUGHING-IN DIMENSIONS

INSTALL SPOUT

Berwick

™

/ Boulevard

Roman Tub Filler

INSTALLATION

INSTRUCTIONS

T430900

T430901

T431900

T431901

Certied to comply with ANSI A112.18.1M

CAUTION

Turn off hot and cold water

supplies before begining.

M965953 Rev. 1.0 (4/19)

1" MAX.

(25 mm)

70mm

(2-3/4")

152-305mm

(6"-8")

57mm

(2-1/4")

108mm

(4-1/4")

52mm

(2")

170mm

(6-3/4")

286mm

(11-1/4")

212mm

(8-3/8")

8" TO 16"

FLEXIBLE INSTALLATION

(203 TO 406 mm)

Adjustable Wrench

Channel Locks

Flat Blade Screwdriver

Phillips Screwdriver

Hex Wench

(supplied)

Hex wench

(supplied)

RECESS

MOUNTING

SURFACE

• Apply 4-5 drops of THREADLOCKER (1)

on DIVERTER INSERT (2) threads (supplied).

NOTE: If installing on nished deck, install DIVERTER

INSERT (2) through WASHER (7).

• Thread DIVERTER INSERT (2) carefully until it touches the

installation surface, be sure the RUBBER RING (5)

is properly seated in it’s RECESS at the base of the

SPOUT (3).

• Thread SET SCREW (4) using 5 mm hex wrench supplied.

Make certain SET SCREW (4) is properly aligned and tight

so that SPOUT (3) is locked in place.

• Install PLUG BUTTON (6).

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Berwick / Boulevard ™ T430900 T430901 T431900 T431901 ® Roman Tub Filler Thank you for selecting American Standard... the benchmark of fine quality for over 140 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.
PAGE 2
VALVE ASSEMBLY • Remove PLASTER GUARDS. • Thread INSERT (1) into SIDE VALVE (2) until it touches the installation surface. • Thread INSERT (3) into SIDE VALVE (4) until it touches the installation surface. 3 • Tighten COUPLING (5) into TEE (6) for products without hand shower. 1 VALVE LOCKING FITTING MOUNTING DECK COLD VALVE LOCKING 4 SPOUT SHANK 6 5 HOT 2 3 INSTALL HANDLES • Turn VALVE to OFF position.
PAGE 3
4 HANDSHOWER INSTALLATION (FOR MODEL T430901 & T431901 ONLY) • Drop SPRAY ESCUTCHEON (1) through the fourth hole of the tub ledge (12” max from SPOUT center) with SPRAY ESCUTCHEON (1) directed towards tub center. Be sure RUBBER RING (2) is properly seated in ESCUTCHEON (1). • Add SEAL WASHER (3) and connect HOSE (8) to outlet nipple at the bottom of TEE (5). Tighten firmly. • Slip SHOWER HOSE (6) with COUPLING NUT through SPRAY HOLDER (4) and ESCUTCHEON (1).
PAGE 4
Berwick™ / Boulevard® Roman Tub Filler MODEL NUMBER M962846-YYY0A SPOUT KIT (WITH TRANSFER) M918378-0070A SET SCREW M962845-YYY0A SPOUT KIT (LESS TRANSFER) T430900 T430901 T431900 T431901 M962850-YYY0A BUTTON AND SCREW M962849-0070A STREAM STRAIGHTENER M962837-YYY0A CROSS HANDLE ASSEMBLY M911810-0070A RUBBER RING M962575-YYY0A TRANSFER KNOB 030278-0070A TRANSFER SEAL KIT M952454-0070A TRANSFER ROD ASSEMBLY M962831-YYY0A LEFT LEVER HANDLE ASSEMBLY 1660609.