Right Height Elongated Toilet Specification Sheet
K51
Revised 2/08
© 2008 AS America Inc.
TROPIC CADET
®
3
RIGHT HEIGHT™ ELONGATED
TOILET
VITREOUS CHINA
TROPIC CADET
®
3
RIGHT HEIGHT™ ELONGATED TOILET
❑ 2459.016
• Vitreous china
• EverClean
®
surface inhibits the growth of
stain- and odor-causing bacteria, mold,
and mildew on the surface
• Low-consumption (6.0 Lpf/1.6 gpf)
• 16-1/2" rim height for accessible application
• Features the Cadet
®
3 Flushing System
• Elongated siphon action jetted bowl
• Fully-glazed 2-1/8" trapway with 2" ball pass
• Generous 9" x 8" water surface area
• Close-coupled tank with at tank cover for
superior storage
• Oversized 3" ush valve with chemical
resistant apper
• Chrome trip lever
• Speed Connect
®
tank-to-bowl coupling system
• Sanitary dam on bowl with four point
tank stabilization
• 2 color-matched bolt caps
• 100% factory ush tested
• 5 year warranty
❑ 3016.016 Right Height™ Elongated Bowl
❑ 4007.016 Tank
Nominal Dimensions:
768 x 476 x 784mm (30-1/4" x 18-3/4" x 30-7/8")
Fixture only, seat and supply by others
Alternate Tank Congurations Available:
❑ 4007.516 Tank complete with Aquaguard Liner
Compliance Certications -
Meets or Exceeds the Following Specications:
• ASME A112.19.2M for Vitreous China Fixtures -
includes Flush Performance, Ball Pass Diameter,
Trap Seal Depth and all Dimensions
• Los Angeles Department of Water and Power
Supplementary Purchase Specication for
Non-Adjustability
To Be Specied:
❏ Color: ❏ White ❏ Bone ❏ Silver ❏ Linen ❏ Black
❏ Seat: #5325.010 Elongated Champion
®
Slow Close
solid plastic seat and cover with easy lift off feature
❏ Seat: #5284.016 Elongated EverClean
®
anti-microbial solid plastic seat and cover
❏ Seat: #5321.110 EverClean
®
Elongated Seat with
Slow Close Snap-Off Hinges
❏ Supply with stop:
NOTES:
THIS TOILET IS DESIGNED TO ROUGH-IN AT A MINIMUM DIMENSION OF
305MM (12") FROM FINISHED WALL TO C/L OF OUTLET.
SUPPLY NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED
SEPARATELY.
*
DIMENSION SHOWN FOR LOCATION OF SUPPLY IS SUGGESTED.
IMPORTANT: Dimensions of xtures are nominal and may vary within the range
of tolerances established by ANSI Standard A112.19.2.
These measurements are subject to change or cancellation. No responsibility is
assumed for use of superseded or voided page
FINISHED WALL
FINISHED
FLOOR
C/L OF OUTLET
SUPPLY
AS
REQ'D.
235mm
(9-1/4)
768mm
(30-1/4)
25mm ± 6mm
(1 ± 1/4)
102mm
(4)
464mm
(18-1/4)
476mm
(18-3/4)
784mm
(30-7/8)
419mm
(16-1/2)
*203mm
(8)
305mm
(12)
356mm
(14)
213mm
(8-3/8)
C/L OF SEAT POST HOLES
140mm (5-1/2 CENTERS)
*352mm
(13-7/8)
*152mm
(6)
238mm
(9-3/8)
MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES AND
ANSI A117.1 REQUIREMENTS FOR ACCESSIBLE AND USABLE
BUILDING FACILITIES-CHECK LOCAL CODES.