Installation Guide

ManualsBrandsAmerican Standard ManualsBathOvation 33.75 in. x 60 in. x 75 in. Standard Fit Bathtub Kit with Right-Hand Drain in Arctic

754916-100

OVATION

™

TUB

HIGH GLOSS ACRYLIC SURFACE

INSTALLATION INSTRUCTIONS

BEFORE YOU BEGIN....

Local building codes vary by location. Observe all local plumbing and building codes.

Your new bath is shipped to you after careful inspection. All you need to finish the installation are your selected fittings.

To ensure maximum performance and pleasure from this product, please follow the instructions and cautions.

TOOLS & MATERIALS REQUIRED....

NOTE: Take extra care in handling surfaces of the bath. Use only non-abrasive cloths to avoid scratching.

• Level

• Square

• Tape Measure

• Pipe Wrench

• Slip Joint Pliers

• Nails

• Plumber’s Putty

• Silicone Sealant

• 1 x 3 or 2 x 4 Stringers

• Drop Cloth

• Mortar Mix or Grout

TOOLS:

• Screw Driver

• Standard Woodworking Tools

• Personal Safety Equipment

• Caulking Gun

MATERIALS:

MODELS: 2647.112 & 2647.212

USED WITH BATH WALLS: 3060BW1

Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed

properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be

sure your installation conforms to local codes.

Product names listed herein are trademarks of AS America, Inc.

GENERAL INSTALLATION INFORMATION ...

1. When installing the matching ovation bath walls (model 3060BW1), additional studs may be required.

Refer to those installation instructions prior to installing tub.

2. Ovation bath walls are to be installed over stud walls.

3. Bath may only be installed in a recess type installation.

4. It is recommended that the tub be set in a small bed of mortar or grout tocompensate for uneven floors.

Stringers will help level tub but will not provide adequate support.

5. Take extra care when driving nails or screw to avoid damaging the bath.

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS OVATION™ TUB HIGH GLOSS ACRYLIC SURFACE MODELS: 2647.112 & 2647.212 USED WITH BATH WALLS: 3060BW1 Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes. BEFORE YOU BEGIN.... Local building codes vary by location.
PAGE 2
ROUGH-IN INFORMATION: OVATION TUB 60" (1524mm) 9-1/2" (241mm) 15" (381mm) 3-1/16" (78mm) 3-13/16" (97mm) 30" (762mm) 1-7/8" (48mm) C/L of pipe location from tub edge 33-3/4" (857mm) 3-1/2" (89mm) 3" (76mm) GENERAL SPECIFICATIONS FOR 2647 TUB 60 x 30 x 18 In. (1524 x 762 x 457mm) 60 Lbs. (27 Kg) WEIGHT WEIGHT w/WATER 435 Lbs.(197 Kg) 45 Gal. (170 L) GAL. TO OVERFLOW 22.25 x 44.25 In.(565 x 1124mm) BATHING WELL AT SUMP BATHING WELL AT RIM 27.75 X 53.125 In.(705 x 1349mm) 11.25 In.
PAGE 3
2 A.) THIS BATH MUST BE SUPPORTED ALONG IT'S ENTIRE BOTTOM. We recommend the use of mortar as bedding material (sand is not recommended). Apply enough bedding to support the complete bottom of the bath. After the bedding has been poured, and before it sets, position the bath within the recess until the rim is leveled against the leveling stringers (see "Typical Recess Installation") shown below. The rim of the bath MUST NOT support weight.
PAGE 4
POST INSTALLATION CLEAN-UP Remove all construction debris from bath. Tile grout can be removed with a wooden popsicle stick or tongue depressor. Do not use wire brushes or any other metal implement on bath surface. Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent. Stubborn dirt or ® stains may be removed using granular Spic and Span mixed with water. Painter's naphtha can be used to remove excess adhesives and/or wet oil-base paint.