Williamsburg 1.6 GPF One-Piece Toilet Installation Instructions

ManualsBrandsAmerican Standard ManualsIndoor FurnishingWilliamsburg One-Piece Elongated Toilet 2038.700

RECOMMENDED TOOLS AND MATERIALS

Putty Knife Regular Screwdriver Adjustable Wrench Sealant Tape Measure

Hacksaw Wax Ring/Gasket Flexible Supply Tube Closet Bolts Carpenters Level

1 REMOVE OLD TOILET

a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.

b. Disconnect and remove supply line. NOTE:

If replacing valve, first shut off main water supply!

c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.

d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.

NOTE:

Mounting surface must be clean and level before new toilet is installed!

INSTALL CLOSET BOLTS

Install closet bolts in flange channel, turn 90

, and slide

into place 6" (152 mm) apart and parallel to wall.

SAVE FOR FUTURE USE

CLOSET FLANGE

CLOSET BOLTS

730488-100 Rev. A

Saniwares

CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

Product names listed herein are trademarks of American Standard Inc.

NOTE:

Pictures may not exactly define contour of china and components.

WILLIAMSBURG 1.6 GPF ONE-PIECE TOILET

2038.700

ROUGHING-IN DIMENSIONS:

NOTE:

Distance from wall to closet flange centerline must be as listed below:

Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product

is installed properly, please read these instructions carefully before you begin. (Certain installations may require

professional help.) Also be sure your installation conforms to local codes.

INSTALLATION

INSTRUCTIONS

INSTALL WAX SEAL

Invert toilet on floor (cushion to prevent damage), and

install wax ring evenly around waste flange (horn), with

tapered end of ring facing toilet. Apply a thin bead of

sealant around toilet base.

POSITION TOILET ON FLANGE

a. Unplug floor waste opening and install toilet on closet flange so bolts project

through mounting holes.

b. Loosely install retainer washers and nuts. Side of washers marked "THIS

SIDE UP"

must

face up!

WAX RING

SEALANT

C/L OF OUTLET

C/L OF SUPPLY

AS REQUIRED

FINISHED WALL

FINISHED

FLOOR

737mm

(29)

(5)

686mm

(27)

127mm

83mm

(3-1/4)

305mm

(12)

457mm

(18)

C/L

WASHER

NUT

FLANGE

BOLT

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS WILLIAMSBURG 1.6 GPF ONE-PIECE TOILET 2038.700 Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes. ! CAUTION: PRODUCT IS FRAGILE.
PAGE 2
6 BOLT CAP CLOSET FLANGE BOLTS INSTALL TOILET a. Position toilet squarely to wall and, with a rocking motion, press bowl down fully on wax ring and flange. Alternately tighten nuts until toilet is firmly seated on floor. ! CAUTION: DO NOT OVERTIGHTEN NUTS OR BASE MAY BE DAMAGED! b. c. 7 Install caps on washers. (If necessary, cut bolt height to size before installing caps.) Smooth off the bead of sealant around base. Remove excess sealant.
PAGE 3
9 ARM TOP 10 REFILL TUBE NIPPLE ADJUSTMENTS a. TANK LEVER CRITICAL LEVEL MARK ("C.L.") MUST BE 1" ABOVE OVERFLOW PIPE Fig. 10A "S" CLIP FLOAT CUP Adjust water level. Water level should be adjusted to level indicated on tank by adjusting float cup. See Step 10 for water level adjustment method FILL VALVE FLUSH VALVE WATER LEVEL ADJUSTMENT CLIP b. LINK VALVE BODY ADJUSTABLE HEIGHT FLAPPER SHANK WASHER If bowl fails to siphon, an adjustment may be required with the lift chain.
PAGE 4
TROUBLESHOOTING 12 IF FILL VALVE SHUTS OFF BUT CONTINUES TO LEAK SLOWLY, repeat Step 12. IF FILL VALVE TURNS OFF AND ON DURING PERIODS OF NON-USE, it is a signal you are wasting water because: • The end of the refill tube is inserted into overflow pipe, below water level in tank. Attach refill tube to overflow pipe using "S" clip provided. LIFT ARM FIRST LIFT ARM FIRST • The flush valve is leaking because it's worn, dirty or misaligned with tank ball or flapper (replace with a new flapper).