SDS

ManualsBrandsAmes ManualsConcrete SealersBlock and Wall 1 Gallon Acrylic Waterproof Coating

Page 1 of 11

Ames’ Block & Wall Liquid Rubber

™

Product Name (as used on Label and List)

Color: White

Revision Date: 9-2-16

GHS Safety Data Sheets (SDS)

SECTION 1 – IDENTIFICATION

PRODUCT NAME

Ames’ Block & Wall Liquid Rubber

™

OTHER MEANS OF

IDENTIFICATION

BWRF

END USE

Rubber paints and coatings, water borne dispersion

MANUFACTURER

Ames Research Laboratories, Inc.

Salem, Oregon 97302

Corporate Office:

1891 16

Street SE

Salem, Oregon 97302-1436

(503) 588-3330

EMERGENCY PHONE

NUMBER

1-888-345-0809 or Chemtrec 1-800-424-9300

SECTION 2 – HAZARD IDENTIFICATION

CLASSIFICATION

Acute Toxicity, Dermal – 5:

Serious Eye Damage/Eye Irritation – 2B:

SIGNAL WORD

WARNING

HAZARD

STATEMENT

May be harmful in contact with skin (H313)

Causes eye irritation (H320)

HAZARD

PICTOGRAMS

N.A. – No Symbol

PRECAUTIONARY

STATEMENT(S)

Wear protective gloves/protective clothing/eye

protection/face protection. Avoid breathing

dust/fume/gas/mist/vapor/spray. Use in well-ventilated area.

If hands or other body parts come in contact, wash

thoroughly after handling.

IF IN EYES: Rinse cautiously with water for several

minutes. Remove contact lenses, if present and easy to do

so. Continue rinsing. (P305+P351+P338) If eye irritation

persists: Get medical attention from a physician.

(P337+P313)

IF ON SKIN: Call a POISION CENTER or

doctor/physician if you feel unwell. (P312)

HAZARDS NOT

OTHERWISE

CLASSIFIED

N.A.

Summary of content (11 pages)

PAGE 1
Ames’ Block & Wall Liquid Rubber™ Product Name (as used on Label and List) Color: White Revision Date: 9-2-16 GHS Safety Data Sheets (SDS) SECTION 1 – IDENTIFICATION PRODUCT NAME Ames’ Block & Wall Liquid Rubber™ OTHER MEANS OF BWRF IDENTIFICATION END USE Rubber paints and coatings, water borne dispersion MANUFACTURER Ames Research Laboratories, Inc.
PAGE 2
Ames’ Block & Wall Liquid Rubber™ Product Name (as used on Label and List) Color: White Revision Date: 9-2-16 GHS Safety Data Sheets (SDS) SECTION 3 – COMPOSITION/INFORMATION ON INGREDIENTS SUBSTANCE / Mixture MIXTURE OTHER MEANS OF N.A.
PAGE 3
Ames’ Block & Wall Liquid Rubber™ Product Name (as used on Label and List) Color: White Revision Date: 9-2-16 GHS Safety Data Sheets (SDS) SECTION 5 – FIRE FIGHTING MEASURES EXTINGUISHING To extinguish combustible residues of this product, use MEDIA: SUITABLE water fog, CO2, dry chemical, chemical foam or alcoholMEDIA resistant foam EXTINGUISHING N/A MEDIA: UNSUITABLE MEDIA SPECIFIC HAZARDS Under fire conditions, some components of this product ARISING FROM THE may decompose.
PAGE 4
Ames’ Block & Wall Liquid Rubber™ Product Name (as used on Label and List) Color: White Revision Date: 9-2-16 GHS Safety Data Sheets (SDS) SECTION 7 – HANDLING AND STORAGE PRECAUTIONS FOR SAFE HANDLING PROTECTIVE Use in a well ventilated area. Keep out of reach of children. MEASURES If user operations generate dust, fume, or mist, use ventilation to keep exposure to airborne contaminants below the respective exposure limits. Use goggles and gloves. Similar to most latex paints.
PAGE 5
Ames’ Block & Wall Liquid Rubber™ Product Name (as used on Label and List) Color: White Revision Date: 9-2-16 GHS Safety Data Sheets (SDS) BOILING POINT FREEZING POINT FLASH POINT EVAPORATION RATE FLAMMABILITY (SOLID, GAS) UPPER / LOWER FLAMMABILITY OR EXPLOSIVE LIMITS VAPOR PRESSURE VAPOR DENSITY RELATIVE DENSITY SOLUBILITY(IES) PARTITION COEFFICIENT: NOCTANOL / WATER AUTO-IGNITION TEMPERATURE DECOMPOSITION TEMPERATURE VISOCITY SPECIFIC GRAVITY 212° F (100° F) 32° F (0° C) N.A. N/A N/A N.A.
PAGE 6
Ames’ Block & Wall Liquid Rubber™ Product Name (as used on Label and List) Color: White Revision Date: 9-2-16 GHS Safety Data Sheets (SDS) SECTION 11 – TOXICOLOGICAL INFORMATION INFORMATION ON TOXICOLOGICAL EFFECTS ACUTE TOXICITY May cause slight transient (temporary) eye irritation. Corneal injury unlikely. Short single exposure not likely to cause significant skin irritation. Prolonged and repeated exposure may cause slight skin irritation. Material may stick to skin causing irritation upon removal.
PAGE 7
Ames’ Block & Wall Liquid Rubber™ Product Name (as used on Label and List) Color: White Revision Date: 9-2-16 GHS Safety Data Sheets (SDS) INGESTION Single dose oral toxicity is considered to be extremely low. No hazards anticipated from swallowing small amounts incidental to normal handling operations.
PAGE 8
Ames’ Block & Wall Liquid Rubber™ Product Name (as used on Label and List) Color: White Revision Date: 9-2-16 GHS Safety Data Sheets (SDS) SECTION 12 – ECOLOGICAL INFORMATION TOXICITY Based largely or completely on information for similar material(s): Material is practically non-toxic to aquatic organisms on an acute basis (LC50 or EC50 > 100 mg/L in the most sensitive species tested). PERSISTENCE AND The polymeric component is not expected to biodegrade.
PAGE 9
Ames’ Block & Wall Liquid Rubber™ Product Name (as used on Label and List) Color: White Revision Date: 9-2-16 GHS Safety Data Sheets (SDS) product is packaged suitably for the mode of transport. All packaging must be reviewed for suitability prior to shipment, and compliance with the applicable regulations is the sole responsibility of the person offering the product for transport.
PAGE 10
Ames’ Block & Wall Liquid Rubber™ Product Name (as used on Label and List) Color: White Revision Date: 9-2-16 GHS Safety Data Sheets (SDS) SECTION 16 – OTHER INFORMATION HMIS HEALTH FLAMMABILITY RATINGS 1 0 REACTIVITY 0 PERSONAL PROTECTION B EUROPEAN PRECAUTIONARY PICTOGRAMS General: If spraying or in poorly ventilated area: PREVIOUS SDS REVISION DATE REASON FOR REVISION VOLATILE ORGANIC COMPOUNDS (VOC’S) LEGEND ABBREVIATIONS USED NOTICE TO READER 9/15 N/A N/A N.A. – Not Applicable, N.E.
PAGE 11
Ames’ Block & Wall Liquid Rubber™ Product Name (as used on Label and List) Color: White Revision Date: 9-2-16 GHS Safety Data Sheets (SDS) ensure that their activities comply with all country, federal, state, provincial or local laws. The conditions for use of the product are not under the control of the manufacturer; the customer/buyer/user is responsible to determine the conditions necessary for the safe use of this product.