AMIC A9245-D UHF RFID Reader User Manual Rev 1.2 © AMIC 2010 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from AMIC. AMIC Technology Corporation. th No.2, Li-Hsin 6 Road, SBIP, 300 Hsinchu, Taiwan, R.O.C TEL: 886-3-5679966 FAX: 886-3-5679977 © AMIC March.
Trademarks: All trademarks mentioned herein are properties of their respective companies © AMIC March.
A9245-D User Guide FCC INFORMATION The Federal Communication Commission Radio Frequency Interference Statement includes the following paragraph: The equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
A9245-D User Guide 1. Introduction Thank you for purchasing AMIC A9245-D UHF RFID readers. A9245-D UHF RFID readers are designed to compliant with EPC Global Gen2 specifications. They are easy to use and simple installations. These readers are equipped with standard RS-232 host interface, and come with GPIO for external device controls. 2. Product Contents Before starting using the A9245-D RFID reader, first please check that the package contains the following items: One A9245-D UHF RFID reader.
A9245-D User Guide 2.1. Installation Requirements AMIC A9245-D requires the following minimum system environment for proper operation: Minimum System Requirement: PC Processor: Pentium 1.7GMHz or faster Memory: 256MB RAM Interface: One RS-232 compliant port Hard Disk Space: 10MB of free disk space Operation system: Windows 2000 Windows XP Reader Antenna (optional equipment) Part number Antenna Gain Connector type Polarization A9295-A-0K 12.0 dBi N-Female vertical linear 5.
A9245-D User Guide © AMIC 2010 – All rights reserved p4 of 8 Rev 1.
A9245-D User Guide 3. Nomenclature 1 6 2 5 3 4 Item Name Description 1 DC Power Jack The DC power input is +5V. An UL approved 110 / 240VAC to +5VDC power adapter capable of supplying at least 6A current should be used.
A9245-D User Guide Item Name Description DB-9 male receptacle for host PC communication. 3 4 RS-232 Host Interface Connector GPIO Connector Pin No. Signal 2 3 5 All others RS-232 TX RS-232 RX Ground Reserved for future usage Signal Pin Pin No. 1~4 5 6 1 2 3 4 5 1 6 Signal Auxiliary digital output ports 1 through 4 (DC +5V / 0V) Ground Auxiliary digital input port (DC +5V / 0V) 5 Power LED When power to the unit is on, the red LED will light.
A9245-D User Guide 4. Connect to A9245-D UHF RFID Readers Step 1: Connect antenna to the reader. Step 2: Connect RS-232 cable to the rader and the host PC. Step 3: Plug in the power cord into the DC power jack. Step 4: Plug in power supply’s power cord into AC power source. Step 5: Launch the demo utility software included on the Demo Utility CD. For details of the demo utility please see demo utility user guide on the CD-ROM.
A9245-D User Guide Professional Installation Guide Installation with FCC Approval (1) This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. (2) Electrical connection, commissioning, measurement, maintenance, and calibration work on the unit is to be performed only by electrical specialists or persons with equivalent training.
A9245-D User Guide 7. Revision History Revision Date Description By _____________________________________________________________________________ 1.0 12/05/2008 Initial creation H. Yu 1.1 05/21/2010 Addition of Professional Installation Guide P. Liao. 1.2 06/30/2010 Added antenna selection table and remark P. Liao © AMIC 2010 – All rights reserved p9 of 8 Rev 1.
