Operating manual Washing machine AWCM 10L + STANDBY 1000 ZIMNA COLD 95 C 60 C 40 C 30 C WODA RUN EXTRA RINSE INTENSIVE WASH SHORT WASH EASY IRON 400 0 END DELICATE WOOL HAND WASH SYNTHETICS REFRESH WHITES COLOURS COTTON EVERYDAY EFFECT PLUS RINSING RINSING AUTO DRAIN SPINNING Start up your washing machine only once you’ve read the Manual and the abridged Instructions for Use!
Table of contents General information........................................................................................................3 Safety instructions .........................................................................................................4 Installation.......................................................................................................................5 Troubleshooting guide........................................................................................
Dear Customer By reading this Manual you will become a conscious user of new washing machine, a modern and technologically advanced product. The new automatic washing machine has been designed by technicians and engineers working in constructional and research forces, using the latest technical knowledge and modern designing tools. It is a perfect response to the key needs of the market such as demand of reliability, func tionality, simplicity of operation and modern design.
Safety instructions Burns The window and door of your washing machine are hot during op eration. Do not allow children in the vicinity of the appliance. Use only those washing agents and bleaches that are appropriate for washing in automatic washing machines. Washing agents Do not use any solvent-containing washing agents as they may dam age some parts of the appliance or may release poisonous gases and create ignition and explosion danger.
Installation I. Remove all the packing materials (keep them for future use!) lUnscrew the screws using a screwdriver. lUnscrew the bolts that fix the guard. lRemove the transport guard lUnscrew the bolt together with sleeves and bolts. lRemove the sleeve and bolt. Before you start up the appliance check that all the locking devices are removed ! Do not place washing machine on a carpet! lPlug holes with stoppers. II.
III.Water supply Inlet hose with seals. Water pressure min.1bar, max. 8 bar. Feed the appliance only with cold water! IV.Water outlet max 100 cm min. 50 cm Secure the drain hose so it does not move dur ing operation! Do not insert the drain hose too dip into the water pipe! V.Power supply lThe connection must be made with a correctly installed, earthed 6 and insulated socket! Do not use extension cords! lBroken power leads may be replaced only by authorised serv icemen.
Troubleshooting guide Flashing signal light TEMPERATURE STANDBY SPIN SPEED COLD RUN 1000 END Shining signal light The washing machine has been equipped with a system that with use of “Temperature” LEDs per forms signalling in case of some problems related with the incorrect operation. Reason of displaying a code What you should do by yourself I.The appliance will not operate STANDBY RUN END TEMPERATURE Now display ! COLD l Insert correctly a plug into a socket. l Check fuses located at home.
VI.No water in the washing machine STANDBY RUN TEMPERATURE lOpen the tap. lClean the mesh filter on the water supplying hose. COLD END Code: shinning signal light 95oC + 60oC + COLD VII.Washing interrupted STANDBY RUN TEMPERATURE COLD lClean the pump filter. lClean the water outlet hose. END Code: shining light 95oC + 60oC + 30oC l Washing machine does not pump the water off. VIII.Water under washing machine lTighten the pump filter. lCheck the drain hose and fasten it if necessary IX.
XIII.Poor rinsing results lAdjust the dose of the washing agent to the degree of soiling and water hardness (see recommendations on the washing agent packaging). lSelect appropriate programme. The appliance remembers the last error. To cancel the error sign press START button for approx. 3 sec. (see Cancelling a programme). If error occurs, the appliance will lock the door.
Maintenance and cleaning Never use solvents or sharp, abrasive cleaning agents (for example cleaning powders) to clean the cover and plastic parts! Clean the appliance using delicate, liquid cleaning agents. Clean the filter periodically, after approx. 20 washing cycles. Forgetting to clean the filter may cause diffi culties in draining water from the appliance! I. Pump filter lOpen the door lTake out the release lRemove the plug from the lRemove the filter lRemove the filter pad.
Practical washing hints I. Cancelling and changing the programme To stop a washing programme, press the START pushbutton and keep it depressed until the signal light READY switches on. When the washing machine is already operating, to change the programme you must first stop the one presently selected by pressing the START pushbutton (see above) and then you may select the desired programme.
V. Displayed information Shining signalling lamp indicates spin speed setting TEMPERATURE STANDBY COLD RUN SPIN SPEED 1000 END Shining signalling light indicated washing temperature setting Temperature adjustment Spin speed adjustment Temperature correction Pressing continually “TEMPERATURE” pushbutton causes cyclical setting changes.
Warning! The more delicate textile, the lower temperature and spin rotations should be selected. For silk, wool and other delicate textiles “Stop with water” option is the most ap propriate. The range of max. temperature and spin rotations adjustments for the respective programmes is specified in the “Programme table” Special functions “Pre-wash”Displayed symbol: Function used before the main wash of heavy soiled textiles, ex tends the wash time by 30 – 50 min.
VI. Door lock The appliance is equipped with a door lock, which prevents opening the appliance door during the washing process. In case after interrupting the cycle or after finishing washing you cannot open the door it means that the door lock is still active. To open the door wait for approximately 2 minutes.
IX. Dosage Insufficient dose of the washing agent causes: l Grey laundry. l Pellets of oil, built up scale. Overdosing the washing agent causes: l Excessive foaming lReduced washing efficiency, poor rinsing results. X. Savings Energy and water l Wash lightly soiled linen applying Refreshing, Every Day programme or activate „short wash” function with a selected washing programme. l Using the optimum dosages of washing agents do not require additional rinse. XI.
Technical data - Type - Rated voltage - Rated power - Overcurrent protection - Maximal load - Water pressure - Dimensions - Weight - Complies with EC regulations AWCM 10L 230V / 50Hz 2300 W 10 A max. 6,0 kg min. 1,0 bar, max.