Operating manual Washing machine AWCT 10L AWCT 12L Start up your washing machine only once you’ve read the Manual and the abridged Instructions for Use! IOAP-239 (11.2008.
Table of contents General information........................................................................................................3 Safety instructions .........................................................................................................4 Installation.......................................................................................................................5 Troubleshooting guide........................................................................................
Dear Customer By reading this Manual you will become a conscious user of new washing machine, a modern and technologically advanced product. The new automatic washing machine has been designed by technicians and engineers working in constructional and research forces, using the latest technical knowledge and modern designing tools. It is a perfect response to the key needs of the market such as demand of reliability, func tionality, simplicity of operation and modern design.
Safety instructions Burns The window and door of your washing machine are hot during op eration. Do not allow children in the vicinity of the appliance. Use only those washing agents and bleaches that are appropriate for washing in automatic washing machines. Washing agents Do not use any solvent-containing washing agents as they may damage some parts of the appliance or may release poisonous gases and create ignition and explosion danger.
Installation I. Remove all the packing materials (keep them for future use!) lUnscrew the screws using a lRemove the transport guard screwdriver. together with sleeves and bolts. lUnscrew the bolts that fix the guard. lUnscrew the bolt lRemove the sleeve and bolt. Before you start up the appliance check that all the locking devices are removed ! Do not place washing machine on a carpet! l Plug holes with stoppers. II.
III. Water supply Use new complete hoses supplied together with the equipment. Do not apply the already used hoses. the inlet hose with seals is in the drum of the washing machine Connection of the supply hose with Aqua Stop Water pressure min. 0.1 MPa (1 bar), max 0.8 MPa (8 bar) Feed the cold water to the washing machine exclusively IV. Water outlet max 100 cm min. 50 cm Secure the drain hose so it does not move during operation! Do not insert the drain hose too dip into the water pipe! V.
Troubleshooting guide The appliance is equipped with a system which helps the user at the search for causes and at the localization of little problems resulting from operating errors by means of corre sponding „codes” which are shown by the signal lights at the function keys. The error rec ognition is signalled by blinking START/PAUSE. The error code is shown by appropriately shining signal lights at the function keys. D1 D2 D3 D4 signal light Display of codes I.
Troubleshooting guide III. Low pressure lCheck pressure in the water supply system. lClean the mesh filter on the water supplying hose. lTurn the tap on completely. Code: shinning signal light D2, D3. IV. Pump filter clogged lClean the filter. Code: shinning signal light D1, D3. V. Washing machine is overloaded lClean the pump filter. lReduce the load. Code: shinning signal light D1, D3, D4. VI. Water under washing machine lTighten the pump filter.
Troubleshooting guide VII. Washing machine moves lRemove the transport locking devices. lPlace the machine in a perfectly hori zontal position. lLock the feet (tighten the locknuts). VIII. Washing interrupted lSwitch XI. Poor final spin results lClean X. Foam formation lCheck the washing program CONDITIONING on, in order to remove the foam residues from the laundry. nance). the pump filter (see mainte water hardness and adjust the dose of the washing agent. lCheck water hardness.
Troubleshooting guide If error occurs, the washing machine will lock the door. To open the door, selection knob in the position and wait approximately 2 minutes. If the display of error codes shows an error different from the above mentioned errors or the recommended activities do not help, you should: lwrite down the error code lswitch off the appliance lpull out the mains plug lcall the service Care label symbols I. Washing boiling temp. 950C normal temp. 600C delicate normal temp. 400C manual II.
Maintenance and cleaning Never use solvents or sharp, abrasive cleaning agents (for example cleaning powders) to clean the cover and plastic parts! Clean the appliance using delicate, liquid cleaning agents. Clean the filter periodically, after approx. 20 washing cycles. Forgetting to clean the filter may cause diffi culties in draining water from the appliance! I. Pump filter lOpen the door lTake out the release lRemove the plug from the lRemove the filter lRemove the filter pad.
Practical washing hints I. Cancelling and changing the programme If you want to stop a programme, keep pressing button until READY lamp is lighted. If you want to change a programme when the appliance is in operation, first stop the current programme by pressing START button (see above) and then select another programme. If you change position of the programme selector knob without cancelling the programme, the run programme will still not be changed. II.
Practical washing hints IV. Displayed information Washing program selection Additional function START/PAUSE Spin rotation speed reduction After the washing program DELICATE has been brought to its end, the water from the last rinse remains in the tub (see the „washing program table” enclosed to the instructions of use.) To take out the laundry from the appliance, you have to: l start the washing program DRAINING.
Practical washing hints V. Load Load articles into the drum observing the following instructions: cotton – maximally full drum (do not force articles into the drum as it may reduce the washing efficiency!). synthetic – maximally 1/2 drum wool, silk, delicate fabrics - maximally 1/3 drum Warning! Do not overload the appliance! Overloading may cause damages to the washed articles! VI. Even load distribution control The electronic control device includes a load distribution control sys tem.
Practical washing hints IX. Dosage Insufficient dose of the washing agent may cause: Grey laundry. Pellets of oil, built up scale. Overdosing the washing agent causes: Excessive foaming. Reduced washing efficiency, poor rinsing results. X. Savings Energy Wash lightly soiled linen in low washing temperatures. Use Refreshing programme, activate “short wash” function with a se lected washing programme.
Technical data l l l l l l l l l Type Rated voltage Rated power Overcurrent protection Maximal load Water pressure Dimensions Weight Complies with EC regulations AWCT 10L/AWCT 12L 230V / 50Hz 2300 W 10 A max.
TECHNICAL SPECIFICATION (In accordance with the Regulation of the Minister of Economy, Labour and Social Policy dated April 2003 on the requirements regarding the energy efficiency). Wronki S.A.
Amica Wronki S.A. ul.Mickiewicza 52 64-510 Wronki tel. 067 25 46 100 fax 067 25 40 320 www.amica.com.
