EHC* 213C* 213C*Ts* (EN) INSTRUCTION MANUAL....................................2 (NL) GEBRUIKERSHANDLEIDING...............................36 IOAK-1683 / 8048601 (12.2010.
DEAR CUSTOMER, The cooker is exceptionally easy to use and extremely efficient. After reading the instruction manual, operating the cooker will be easy. Before being packaged and leaving the manufacturer, the cooker was thoroughly checked with regard to safety and functionality. Before using the appliance, please read the instruction manual carefully. By following these instructions carefully you will be able to avoid any problems in using the appliance.
Table of Contents Safety instructions.............................................................................................................. 4 Description of the appliance.............................................................................................. 7 Installation...........................................................................................................................11 Operation..........................................................................................
SAFETY INSTRUCTIONS The appliance becomes hot during operation. Take care not to touch the hot parts inside the oven. Always keep children away from the cooker. While in operation direct contact with the cooker may cause burns! Ensure that small items of household equipment, including connection leads, do not touch the hot oven or the hob as the insulation material of this equipment is usually not resistant to high temperatures. Do not leave the cooker unattended when frying.
HOW TO SAVE ENERGY Using energy in a responsible way not only saves money but also helps the environment. So let’s save energy! And this is how you can do it: Make use of residual heat from the oven. If the cooking time is greater than 40 minutes switch off the oven 10 minutes before the end time. Important! When using the timer, set appropriately shorter cooking times according to the dish being prepared. Use proper pans for cooking. Pans with thick, flat bases can save up to 1/3 on electric energy.
Disposal of the appliance UNPACKING During transportation, protective packaging was used to protect the appliance against any damage. After unpacking, please dispose of all elements of packaging in a way that will not cause damage to the environment. All materials used for packaging the appliance are environmentally friendly; they are 100% recyclable and are marked with the appropriate symbol.
DESCRIPTION OF THE APPLIANCE 10 11 7 8 3, 4 5, 6 2 1 9 1 Temperature control knob 2 Oven function selection knob 3, 4, 5, 6 Heating zone control knobs 7 Temperatureregulatorsignal light red 8 Cooker operation signal light yellow 9 Oven door handle 10 Ceramic hob 11 Electronic programmer* MENU Control button „-” Menu button *optional 7 Control button”+”
DESCRIPTION OF THE APPLIANCE Ceramic hob 4a 5a 3a 3a 4a 5a 6a Ø 18 cm Ø 14,5 cm Ø 21 cm Ø 14,5 cm 3a 4a 5a 6a Ø 18 / Ø 12 cm Ø 14 x 25 cm Ø 18 cm Ø 14,5 cm 6a Zone heating indicator 4a 3a 5a 6a 8
SPECIFICATIONS OF THE APPLIANCE Cooker fittings: Grill grate (drying rack) Baking tray* Roasting tray *optional 9
INSTALLATION Making the worktop recess ● The kitchen area should be dry and aired and equipped with efficient ventillation. When installing the cooker, easy access to all control elements should be ensured. This is a Y–type design built–in cooker, which means that its back wall and one side wall can be placed next to a high piece of furniture or a wall. ● Worktop thickness should be 28 - 40 mm, while its width at least 600 mm. The worktop must be flat and level.
INSTALLATION Installation of self-adhesive foam gasket Do not install the appliance without the foam gasket. The gasket must be applied on the appliance as follows: Before fitting the appliance in the kitchen worktop, apply self-adhesive foam gasket provided underneath the rim.
INSTALLATION Installing the hob in worktop opening ● Use four “A” brackets for 38 mm thick worktops. Fit the hob into worktop opening as shown on figure 2 and 3. To properly secure hob in 28 mm thick worktop, use four 15x15x50 mm wooden blocks in addition to “A” brackets. Fit the hob into worktop opening as shown on figure 4 and 5. ● Check if adhesive seal is properly applied to the hob's flange.
INSTALLATION Installing the hob in worktop opening 5 4 15 4 1 15 2 6 3 min 50 560 290 490 5 min 60 240 13 50 1 - worktop 2 - screw 3 - fixing bracket 4 - hob 5 - seal 6 - wooden block
INSTALLATION Assembly of the oven: Make an opening with the dimensions given in the diagram for the oven to be fitted.(Fig.A) Make sure the mains plug is disconnected and then connect the oven to the mains supply. Partially insert the oven into the prepared opening and connect the oven to the hob. (Fig.B) The appliance must be earthed.
INSTALLATION Electrical connection Warning! All electrical work should be carried out by a suitably qualified and authorised electrician. No alterations or wilful changes in the electricity supply should be carried out. Fitting guidelines 3 The cooker is manufactured to work with three–phase alternating current (400V 3N~50Hz). The voltage rating of the cooker heating elements is 230V.
INSTALLATION Connection diagram Caution! Voltage of heating elements 230V Caution! In the event of any connection the safety wire must be connected to the PE terminal 1 2 3 For 230 V earthed one–phase connection, bridges connect 1–2–3 terminals and 4–5 terminals, safety wire to . Recommended type of connection lead H05VV-F3G4 For 400/230 V earthed two–phase connection, bridges connect 2–3 terminals and 4–5 terminals, the safety wire to .
OPERATION Important! Before first use In ovens equipped with the electronic programmer Ts, the time “0.00” will start flashing in the display field upon connection to the power supply. The programmer should be set with the current time. (See Electronic programmer ). If the current time is not set operation of the oven is impossible. Remove packaging, clean the interior of the oven and the hob. Take out and wash the oven fittings with warm water and a little washing–up liquid.
OPERATION Controlling the heating zones of the ceramic hob. Choice of cookware Choose a pan with a diameter that is at least as large as the heating zone. For roasting tins there is a special widened heating zone of 140x250. Do not use pans with a concave or convex base. Always remember to put a proper cover on the pan. We recommend the use of pans with thick, even bases. If the heating zones and pans are solied it is impossible to make full use of the heat.
OPERATION Zone heating indicator Switching on the wider heating zone If the temperature of a heating zone exceeds 50°C this is signalled by an indicator which lights up for that zone. When the heating indicator lights up it warns the person using the cooker against touching a hot heating zone. For about 5 to 10 minutes after a heating zone is switched off it will still have residual heat that can be used, for example to warm up or keep dishes warm without switching on another heating zone.
OPERATION Electronic programmer* Timer The timer can be activated at any time, regardless of the status of other functions. The timer can be set for from 1 minute to up to 23 hours and 59 minutes. To set the timer you should: functions 1– 2– 3– function selection button “–” sensor “+” sensor Press sensor 1, then the display will show flashing , The electronic prgrammer is equipped with electronic sensors which are switched on by touching or pressing the sensor surface for at least one second.
OPERATION Semi–automatic operation Automatic operation If the oven is to be switched off at a given time, then you should: If the oven is to be switched on for a specified period of time and switched off at a fixed hour then you should set the operation time and the operation end time: Set the oven function knob and the temperature regulator knob to the setting at which you want the oven to operate.
OPERATION Change the timer beeps The function AUTO is now on; the oven will start operating from the point when the difference between the set operation end time and the operation duration time occurs (e.g. the operation time is set to 1 hour, the operation end time is set to 14.00, so the oven will start working automatically at 13.00).
OPERATION Bottom heater on When the knob is set to this position the oven is heated using only the bottom heater. Baking of cakes from the bottom until done (moist cakes with fruit stuffing). Oven functions and operation. Natural convection oven (conventional) The oven can be warmed up using the bottom and top heaters, as well as the grill.
OPERATION Oven with automatic air circulation (including fan) 0 Oven is off Independent oven lighting Set the knob in this position to light up the oven interior. The oven can be warmed up using the bottom and top heaters, as well as the grill. Operation of the oven is controlled by the oven function knob – to set a required function you should turn the knob to the selected position, as well as the temperature regulator knob – to set a required function you should turn the knob to the selected position.
OPERATION Enhanced roaster (super roaster) In this setting both roaster and top heater are on. This increases temperature in the top part of the oven’s interior, which makes it suitable for browning and roasting of larger portions of food. Fan and combined grill on When the knob is turned to this position, the oven activates the combined grill and fan function. In practice, this function allows the grilling process to be speeded up and an improvement in the taste of the dish.
OPERATION Use of the grill The grilling process operates through infrared rays emitted onto the dish by the incandescent grill heater. In order to switch on the grill you need to: Set the oven knob to the position marked grill , Heat the oven for approx. 5 minutes (with the oven door shut). Insert a tray with a dish onto the appropriate cooking level; and if you are grilling on the grate insert a tray for dripping on the level immediately below (under the grate). Close the oven door.
BAKING IN THE OVEN – PRACTICAL HINTS Baking we recommend using the baking trays which were provided with your cooker; it is also possible to bake in cake tins and trays bought elsewhere which should be put on the drying rack; for baking it is better to use black trays which conduct heat better and shorten the baking time; shapes and trays with bright or shiny surfaces are not recommended when using the conventional heating method (top and bottom heaters), use of such tins can result in undercooking th
BAKING IN THE OVEN – PRACTICAL HINTS Oven type: EHC 12406 E Type of dish Oven functions Temperature Level Time 160 - 200 2-3 30 - 50 160 - 180 2 20 - 40* 220 - 240 3 10 - 15 210 - 220 2 45 - 60 230 - 250 4 14 - 18 225 - 250 2 120 - 150 160 - 230 2 90 - 120 160 - 180 2 45 - 60 190 - 210 2 40 - 50 in minutes * Baking smaller items Caution! The figures given in Tables are approximate and can be adapted based on your own experience and cooking preferences.
BAKING IN THE OVEN – PRACTICAL HINTS Type of dish Oven functions Temperature Level Time 160 - 200 2-3 30 - 50 150 3 25 - 35 160 - 180 2 20 - 40* 150 3 65 - 70 220 - 240 3 10 - 15 210 - 220 2 45 - 60 190 2-3 60 - 70 230 - 250 4 14 - 18 225 - 250 2 120 - 150 160 - 230 2 90 - 120 200 - 220 2-3 50 - 60 160 - 180 2 45 - 60 190 - 210 2 40 - 50 170 - 190 3 40 - 50 in minutes * Baking smaller items Caution! The figures given in Tables are approximate and can be adap
CLEANING AND MAINTENANCE By ensuring proper cleaning and maintenance of your cooker you can have a significant influence on the continuing fault-free operation of your appliance. Caution! The sharp blade should always be protected by adjusting the cover (just push it with your thumb). Injuries are possible so be careful when using this instrument – keep out of reach of children. Before you start cleaning, the cooker must be switched off and you should ensure that all knobs are set to the “”/“0” position.
CLEANING AND MAINTENANCE Oven Replacement of the oven light bulb The oven should be cleaned after every use. When cleaning the oven the lighting should be switched on to enable you to see the surfaces better. In order to avoid the possibility of an electric shock ensure that the appliance is switched off before replacing the bulb. Set all control knobs to the position “”/“0” and disconnect the mains plug, unscrew and wash the lamp cover and then wipe it dry.
CLEANING AND MAINTENANCE Dismounting the side racks Ovens marked with the letter D are equipped with easily removable wire guides (side racks*) of oven inserts. To remove them for washing purposes, pull the front catch (Z1), then tilt the guide and remove it from the rear catch (Z2). After washing the guides, put them in the mounting holes of the oven and press the catches (Z1 and Z2).
CLEANING AND MAINTENANCE 4. Clean the panel with warm water with some cleaning agent added. Carry out the same in reverse order to reassemble the inner glass panel. Its smooth surface shall be pointed upwards. Door removal In order to obtain easier access to the oven chamber for cleaning, it is possible to remove the door. To do this, tilt the safety catch part of the hinge upwards. Close the door lightly, lift and pull it out towards you. In order to fit the door back on to the cooker, do the inverse.
CLEANING AND MAINTENANCE Regular inspections Caution! All repairs and regulatory activities should be carried out by the appropriate service centre or by an appropriately authorised fitter. Besides keeping the oven clean, you should: carry out periodic inspections of the control elements and cooking units of the cooker.
TECHNICAL DATA Voltage rating Power rating Cooker dimensions H/W/D Usable capacity of the oven* Energy rating Weight 400/230V~50 Hz max. 10,0 kW 59,5 / 59,5 / 57,5 cm 53-58 litres on the energy label approx. 44 kg Complies with EU regulations EN 50304, EN 60335-1, EN 60335-2-6 standards * according to EN 50304 the capacity depends on the oven fittings – indicated on the energy label.
GEACHTE KLANT, De fornuizen van Amica combineren uitzonderlijk gebruiksgemak en optimale doeltreffendheid. Na het lezen van deze gebruikershandleiding zult u zonder problemen dit fornuis kunnen bedienen. Voor het ingepakt werd en de fabriek verliet, werd dit fornuis bij de controleposten grondig gecontroleerd op het gebied van veiligheid en functionaliteit. Voordat u het toestel aanschakelt, dient u deze gebruikershandleiding grondig door te lezen.
INHOUDSTAFEL Veiligheidsinstructies....................................................................................................... 38 Beschrijving van het toestel............................................................................................. 41 Installatie............................................................................................................................ 44 Bediening.................................................................................................
VEILIGHEIDSINSTRUCTIES Tijdens het gebruik wordt het toestel heet. Wees voorzichtig en raak de hete onderdelen in de oven niet aan. Wees bijzonder voorzichtig als er kinderen in de buurt van het fornuis zijn, want ze kennen de bedieningsprincipes van het fornuis niet.
ENERGIEBESPARING Door op verantwoorde wijze energie te gebruiken bespaart u niet alleen op de kosten van het huishouden, maar werkt u ook bewust mee aan de bescherming van het milieu. Laten we daarom ons steentje bijdragen aan energiebesparing! Dat kan op de volgende manier: Gebruik goede potten en pannen om te koken. Kookpotten en pannen mogen niet kleiner zijn dan de kroon van de vlam van de brander. Dek de potten en pannen steeds af met een deksel.
RECYCLAGE VAN GEBRUIKTE TO ESTELLEN UITPAKKEN Het toestel wordt door zijn verpakking beveiligd tegen beschadigingen tijdens het transport. Na het uitpakken van het toestel dient u de verpakkingselementen te recycleren op milieuvriende- Op het einde van de gebruiksperiode mag dit product niet bij het gewone huisvuil geplaatst worden, maar moet afgegeven worden bij een verzamelpunt voor recyclage van elektrische en elektronische toestellen.
BESCHRIJVING VAN HET TOESTEL 10 11 7 8 3, 4 5, 6 2 1 9 MENU 1 Draaiknop van de temperatuurregelaar 2 Draaiknop voor de keuze van de functie van de oven 3, 4, 5, 6 Draaiknoppen voor de bediening van de kookplaten 7 Controlelampje van de temperatuurregelaar rood 8 Controlelampje voor de werking van het fornuis geel 9 Greep van de deur van de oven 10 Keramische plaat 11 Elektronische programmator* *Bepaalde modellen 41 knop „-” knop MENU knop ”+”
BESCHRIJVING VAN HET TOESTEL Keramische plaat 4a 3a 5a 3a 4a 5a 6a Ø 18 cm Ø 14,5 cm Ø 21 cm Ø 14,5 cm 3a 4a 5a 6a Ø 18 / Ø 12 cm Ø 14 x 25 cm Ø 18 cm Ø 14,5 cm 6a Verwarmingsindicator van een kookveld 4a 3a 5a 6a 42
KENMERKEN VAN HET TOESTEL Uitrusting van het fornuis – overzicht: Grillrooster (droogrekje) Bakplaat voor gebak* Bakplaat voor gebraad *Bepaalde modellen 43
INSTALLATIE Voorbereiding van het meubelblad om de plaat in te bouwen ● De keukenruimte moet droog en goed verlucht zijn en een goed werkende ventilatie bezitten. De opstelling van het fornuis moet een vrije toegang tot alle bedieningselementen garanderen. Het fornuis is ontworpen volgens klasse Y, d.w.z. dat het aan één zijde ingebouwd kan worden tegen een hoog meubel of een muur. ● Het meubelblad moet tussen 28 en 40 mm dik en minimum 600 mm diep zijn. Het blad moet vlak zijn en goed waterpas staan.
INSTALLATIE Montage van de schuimrubber dichting Inbouw van het apparaat zonder dichting is verboden. Breng de dichting als volgt op het apparaat aan: Plak de meegeleverde schuimrubber dichting op de onderkant van het frame van de kookplaat, voordat u het apparaat in het werkblad inbouwt. - verwijder de beschermende folie van de dichting; - plak de dichting vervolgens op de onderkant van het frame (afb.).
INSTALLATIE Montage van de plaat in het meubelblad ● Bij een blad met een dikte van 38 mm moet u 4 bevestigingsgrepen „A” gebruiken om de plaat te bevestigen. De montagewijze is opgegeven op fig. 2 en 3. Bij een blad met een dikte van 28 mm moet u naast de bevestigingsgrepen “A” nog 4 houten blokjes met een afmeting van 15x15x50 mm gebruiken. De montagewijze is opgegeven op fig. 4 en 5. ● Controleer of de pakking goed tegen de plaat aansluit.
INSTALLATIE Montage van de plaat in het meubelblad 5 4 15 4 1 15 2 6 3 min 50 560 290 490 5 min 60 240 47 50 1 - meubelblad 2 - schroef 3 - bevestigingsgreep 4 - kookplaat 5 - pakking van de plaat 6 - houten blokje
INSTALLATIE Montage van de oven: bereid de montageopening voor de oven voor in het meubel volgens de afmetingen die op de figuur aangeduid zijn (fig.A), sluit de oven aan op het stroomnet terwijl de stroom uitgeschakeld is, schuif de oven gedeeltelijk in de voorbereide opening in het meubel en sluit de oven aan op de kookplaat (fig.B). de aardkabel van de plaat (geel-groen) moet verbonden worden met de aardklem van de oven (aangeduid met ) die zich bij de aansluiting bevindt.
INSTALLATIE Aansluiting van het fornuis op de elektrische installatie Opgelet! De plaat mag enkel op de elektrische installatie aangesloten worden door een erkend installateur met de gepaste kwalificaties. Het is verboden om zelfstandig wijzigingen of aanpassingen aan te brengen aan de elektrische installatie. 3 Instructies voor de installateur Het fornuis is in de fabriek aangepast aan voeding met driefasige wisselstroom (400V 3N~50Hz).
INSTALLATIE SCHEMA MET MOGELIJKE AANSLUITINGEN Opgelet! Spanning van de verwarmingselementen 230V Opgelet! Bij elke aansluitingsvariant moet de aardingsleiding aangesloten zijn op de klem 1 2 3 Aanbevolen soort aansluitleiding PE Bij een stroomnet van 230 V eenfasige aansluiting met een nulleiding, de bruggen verbinden de klemmen 1-2-3 en 4-5, aardingsleiding op .
BEDIENING Voordat u het fornuis voor de eerste maal aanschakelt Attentie! In ovens die zijn uitgerust met de elektronische programmeerfunctie Ts, verschijnt na aansluiting op het lichtnet op het display de pulserende tijdsaanduiding „00:00”. verwijder alle verpakkingsonderdelen, verwijder de onderhoudsmiddelen die in de fabriek aangebracht zijn, uit de kamer van de oven en van de kookplaat, Stel de actuele tijd van de programmeerfunctie in.
BEDIENING Bediening van de kookvelden van de keramische plaat. Keuze van potten en pannen Goed gekozen potten en pannen hebben een bodemgrootte en vorm die ongeveer overeenstemt met het gebruiksoppervlak van het kookveld. Voor braadsleden is er een speciaal verbreed kookveld van 140 x 250. Gebruik geen potten en pannen met een holle of bolle bodem. Hou er rekening mee dat de potten en pannen een gepast deksel moeten hebben.
BEDIENING Verwarmingsindicator van een kookveld Aanschakelen van het verbrede kookveld Belangrijk! Het kookveld mag enkel aangeschakeld worden door de draaiknop in wijzerzin te draaien. Als u in de andere richting draait, kunt u de schakelaar beschadigen. Als de temperatuur van een kookveld meer dan 50ºC bedraagt, wordt dit aangegeven door het gepaste veld van de indicator. De verwarmingsindicator van een kookveld waarschuwt de gebruiker zodat hij het aanraken van een heet kookveld kan vermijden.
BEDIENING Voor de elektronische programmator Ts* Opgelet! De oven kan opgestart worden nadat het symbool op de display verschijnt. Veld van de display Nadat het toestel van het stroomnet ontkoppeld wordt of na een stroompanne, onthoudt de programmator de instellingen voor ongeveer 2,5 minuten.
BEDIENING Halfautomatische stand Automatische stand Als de oven zichzelf moet uitschakelen op een bepaald uur, moet u: Als de oven aangeschakeld moet worden voor een bepaalde duur en zichzelf op een bepaald uur moet uitschakelen, dan moeten de werkingstijd en het einduur ingesteld worden: ●druk op sensor 1 totdat de aanduiding op de display begint te knipperen: ● de draaiknop voor de functie van de oven en de draaiknop voor de temperatuurinstelling instellen op de standen, waarin de oven moet werken, ●
BEDIENING Automatische stand Wijziging van de toon van het geluidssignaal Nadat het einduur bereikt is, schakelt de oven zichzelf automatisch uit, slaat het geluidssignaal aan en begint de functie AUTO te knipperen. De toon van het geluidssignaal kunt u op de volgende manier wijzigen: ● druk tegelijkertijd op sensors 2 en 3, ● kies met sensor 1 de functie “toon”.
BEDIENING Verwarmingselement bovenaan aangeschakeld Door de draaiknop in deze stand te plaatsen wordt de oven enkel met behulp van het verwarmingselement bovenaan verwarmd. Bruinen van het gerecht, bijbakken van boven, bijgrillen. Verwarmingselement onderaan aangeschakeld Bij deze stand wordt de oven enkel met het verwarmingselement onderaan verwarmd. Bijbakken van gebak onderaan (bv. vochtig gebak en gebak met vruchten).
BEDIENING Oven met gestuurde luchtcirculatie (met ventilator) 0 Nulstand Onafhankelijke verlichting van de oven Door de draaiknop in deze stand te plaatsen wordt de binnenkant van de oven verlicht. De oven kan verwarmd worden met behulp van een verwarmingselement bovenaan en onderaan en een grillelement (als dat er is).
BEDIENING Supergrill Met de functie „supergrill” worden gerechten gegrild terwijl het verwarmingselement bovenaan ook aangeschakeld is. De functie laat toe om een hogere temperatuur in de bovenlaag van de oven te bereiken, waardoor de gerechten meer gebruind worden. Dit laat ook toe om grotere porties te braden. Het aanschakelen van de oven wordt aangegeven met een rood controlelampje. Als het rode controlelampje uitgaat, heeft de oven de ingestelde temperatuur bereikt.
BEDIENING Gebruik van de grill Tijdens het grillproces ondergaan de gerechten de inwerking van infrarood dat uitgezonden wordt door het verhitte verwarmingselement van de grill. Om de grill aan te schakelen moet u: de draaiknop van de oven op de stand de oven ongeveer 5 minuten verwarmen (met gesloten deur) de bakplaat met het gerecht op het gepaste niveau plaatsen, en als u gebruikt maakt van het spit een bakplaat voor het druipende vet vlak onder het spit plaatsen. de deur van de oven sluiten.
BAKKEN IN DE OVEN – PRAKTISCHE TIPS Gebak het is aan te raden om gebak te bereiden op de bakplaten die deel uitmaken van de uitrusting van het fornuis, gebak kan bereid worden in bakvormen of bakplaten die op het droogrekje geplaatst moeten worden. Voor gebak worden best zwarte bakvormen gebruikt omdat deze beter de warmte geleiden en de baktijd verkorten.
BAKKEN IN DE OVEN – PRAKTISCHE TIPS Oven type: EHC 12406 E Soort gebak gerecht Functies van de oven Temperatuur Niveau Tijd* [min.] 160 - 200 2-3 30 - 50 160 - 180 2 20 - 40* 220 - 240 3 10 - 15 210 - 220 2 45 - 60 230 - 250 4 14 - 18 225 - 250 2 120 - 150 160 - 230 2 90 - 120 160 - 180 2 45 - 60 190 - 210 2 40 - 50 * Kleine gebakjes Belangrijk! De parameters in tabellen geven enkel aanwijzingen en kunnen gecorrigeerd worden volgens uw eigen ervaring en culinaire smaak.
BAKKEN IN DE OVEN – PRAKTISCHE TIPS Soort gebak gerecht Functies van de oven Temperatuur Niveau Tijd* [min.
REINIGING EN ONDERHOUD VAN HET FORNUIS De zorg waarmee de gebruiker het fornuis reinigt en onderhoudt, heeft een belangrijke invloed op zijn levensduur en probleemloze werking. Voor de reiniging moet de oven uitgeschakeld worden. Let er hierbij op dat alle draaiknopen in de stand “”/“0” staan. De oven mag pas gereinigd worden als hij afgekoeld is. Reiniging na elk gebruik • • Licht, niet aangebrand vuil moet verwijderd worden met een vochtige doek zonder reinigingsmiddel.
REINIGING EN ONDERHOUD VAN HET FORNUIS De oven moet na elk gebruik gereinigd worden. Bij de reiniging moet de verlichting aangeschakeld worden, zodat u beter de werkruimte ziet. De kamer van de oven mag enkel met warm water met een beetje afwasmiddel gereinigd worden.
REINIGING EN ONDERHOUD VAN DE OVEN Fornuizen die aangeduid zijn met letter D, zijn uitgerust met gemakkelijk uitneembare staafgeleiders (laddertjes) voor insteekonderdelen van de oven. Om ze te demonteren moet u aan de klem vooraan (Z1) trekken, daarna de geleider wegbuigen en uit de klem achteraan nemen (Z2). Na het reinigen plaats u de geleider terug in de montageopeningen en drukt u de klemmen (Z1 en Z2) weer aan.
REINIGING EN ONDERHOUD VAN HET FORNUIS 4. Was de ruit met warm water en een klein beetje reinigingsmiddel. Ga omgekeerd te werk om de ruit opnieuw te monteren. Het gladde deel van de ruit moet zich bovenaan bevinden. Wegnemen van de deur Om gemakkelijker toegang te hebben tot de ovenkamer en die te reinigen, kunt u de deur wegnemen. Hiervoor moet u de deur openen en de beveiliging op het scharnier naar boven klappen. Doe de deur lichtjes toe, hef ze op en neem ze naar voor toe uit.
REINIGING EN ONDERHOUD VAN HET FORNUIS Periodieke controle Opgelet! Alle herstellingen en instellingen moeten uitgevoerd worden bij een erkende onderhoudsdienst of door een erkend installateur met gepaste kwalificaties. Naast het lopende onderhoud en reiniging van het fornuis moet u ook: regelmatig de werking van de bedieningselementen en de werkende onderdelen van het fornuis controleren.
TECHNISCHE GEGEVENS Nominale spanning Nominaal vermogen Afmetingen van het fornuis Gebruiksinhoud van de oven* Energieklasse Gewicht 400/230V~50 Hz max. 10,0 kW 59,5/59,5/57,5 cm 53-58 liter Zie energie-etiket ca. 44 kg Voldoet aan de vereisten van de Europese voorschriften normen EN 60335-1, EN 60335-2-6 * volgens EN 50304 De capaciteit afhankelijk van de uitrusting van de oven is opgegeven bij de technische kenmerken en op het etiket voor energieverbruik.