ZIM 427
, Before Calling for Service
OFF ON DELAY OFF ON 1 2 S 1 2 D E L AY P RO G .
Before usi ng your dishwasher for the first time: A. B. C. D. Set the water softener Pour 1/2 litre of water inside the salt container and then fill with dishwasher salt Fill the rinse aid dispenser Function of detergent The water softener must be set manually, using the water hardness dial . The water softener is designed to remove minerals and salts from the water, which would have a detrimental or adverse effect on the operation of the appliance.
Always use salt intended for use with dishwasher. The sal t container is locat ed beneath the lower rack and should be filled as foll ows: Atte ntion! Only use salt specifically designed for use in dishwa shers! All other t ypes of salt not spe ci fically designed for use in a dishwasher, e specially table salt, will damage the water softener. In case of dam ages caused by the use of unsui table salt the m anuf acturer does not give any warranty nor is liable for a ny cause d damages.
If there is no rinse-aid w arning light in the control panel, you can judge the amount of rinse-aid by the color of the optical level indicator "D" located next to the cap. When the rinse-aid container is full, the whole indicator will be dark .As the rinse-aid diminishes, the size of the dark dot decreases. You should never let the rinse aid get below 1 / 4 full. D (Rinse-Aid indicator) As the rinse aid diminishes, the size of the black dot on the rinse aid level indicator changes, as illustrated below.
Detergents with its chemical ingredients are necessary to remove dirt, crush dirt and transport it out of the dishwasher. Most of commercial quality detergents are suitable for this purpose.
Fill in detergent 1 Fill the detergent dispenser with detergent. The marki ng indicates the dosing levels , as illustrated on right: 1 The place of main wash cycle detergent placed , “MIN”means approximately 20g of detergen. 2 The place of pre-wash cycle detergent placed , approximately 5g of detergent Please observe the manufacturers dosing and storage recommendations as stated on the detergent packaging. Close the lid and press until it locks in place.
Your dishwasher has a 3 in 1 program which needs not salt and rinse aid but a 3 In1 tablet. And this dishwasher comes with a 3 in 1 tablet container as an accessory. NOTE: Only 3 in 1 program uses 3 in 1 tablet. If using 3 in 1 tablet in other programs, the appliance will not get a best performance. 1、Referring to the below sketch map, hang the 3 in 1 tablet container on the upper basket.
For best performance of the dishwasher, follow these loading guidelines. Features and appearance of racks and silverware baskets may vary from your model. Attention before or after Loading the Dishwasher Racks Scrape off any large amounts of leftover food. It is not necessary to rinse the dishes under running water. Place objects in the dishwasher in following way: 1.Items such as cups, glasses, pots/pans, etc. are stood upside down. 2.
We recommend that you place large items which are most difficult to clean into the low er rack: pots, pans, lids, serving dishes and bowls, as shown in the figure to the right. It is preferable to place serving dishes and lids on the side of the racks in order to avoi d blocking the rotation of the top spray arm. Pots, serving bowls, etc. must always be placed top down. Deep pots should be slanted to allow w ater to flow out.
Silverware Basket Silverware should be placed in the silverware basket with handles at the bottom: If the rack has side baskets, the spoon should be loaded individually into the appropriate slots, especially long utensils should be placed in the horizontal position at th e front of the upper rack.
Di shes and items of cutlery must not lie inside one another, or cover each othe r To avoid damage to glasses, they must not touch Load large items which are most difficult to clean into the lower rack T he upper rack is designed to hold more delicate and lighter dishware such as glasses, coffee and tea cups Attention! Long bladed knives stored in an upri ght position are a potential hazard! Long and/or sharp items of cutl ery such as carving knives must be positioned horizontally in the upper basket.
For normally soiled loads, such as pots , plates,glasses and lightly soiled pans. standard daily cycle. Pre-wash pre-wash wash45 rinse68℃ drying 3in1 160 0.95 14.7 Strong For the heaviest soiled loads, such as pots,pans,casserole dishes and dishes that have been sitting with dried food on them for a while. Pre-wash Pre -wash( 5 0℃) Wash (60 ℃) Rinse (70 ℃) Drying 4/20 g. 160 1.10 12.9 Normal For normally soiled loads, such as pots , plates,glasses and lightly soiled pans. standard daily cycle.
Turning on the Appliance Starting a wash cycle... 1 Draw out the lower and upper basket, load the dishes and push them back. It is commended that loading the lower basket first, than the upper one (see the section entitled “Loading the Dishwasher”). 2 Pour in the detergent (see the section entitled “Salt, Detergent and Rinse Aid”). 3 Insert the plug into the socket. The power supply is 220-240 VAC 50 HZ, the specification of the socket is 12 A 250 VAC.
A forgotten dish can be added any time before the detergent cup opens. 1 2 Open the door a little to stop the washing. 3 Add forgotten dishes. After the spray arms stop working,you can open the door completely. 4 Close the door, the dishwasher will work after ten second. It is dangerous to open the door when washing,because the hot water may scald you. Switch Off the Dishwasher In the digital display appears 0 (remaining programme time), only in this case the programme has ended. 1.
Cleaning the Filters Filter assembly For best performance and results, the filter assembly must be cleaned. The filter efficiently removes food particles from the wash water, allowing it to be reci rculated during the cycle. For this reason, it is a good idea to remove the larger food particles trapped in the filter after each wash cycle by rinsing the semicircular filter and cup under running water. To remove the filter assembly, pull on the cup handle in the upward direction.
To clean the edge around the door, you should use only a soft warm, damp rag. To prevent penetration of water into the door lock and electrical components, do not use a spray cleaner of any kind. Also, never use abrasive cleaners or scouring pads on the outer surfaces because they will scratch the fini sh. Some papers towels can also scratch or leave marks on the surface. OFF ON 1 2 DE LA Y PRO G .
Please carefully read the installation instruction. ● 1 2 Illustrations of cabinet dimensions and installation position of the dishwasher Preparations should be made before moving the dishwasher to the installation place. Choose a place near the sink to facilitate the installation of inlet and drain hoses (see figure 1). If dishwasher is installed at the corner of the cabinet, there should be som e space (illustrated in figure 2) when the door is opened.
2 Install the hook on the aesthetic wooden panel and put the hook into the slot of the outer door dishwasher(see figure 4a). After positioning of the panel , fix the panel onto the outer door by screws and bolts(See figure 4b) . Hop hook 【Figure4a】 Installation of aesthetic panel St4 countersunk head screw Lower hook 4X18 screw 【Figure4b】 Cover Installation of aesthetic wooden panel Spacer for aesthetic panel 1. take away the cover 2. pin up the screw 3.
● Tension adjustment of the door spring The door springs are set at the factory to the proper tension for the outer door. If aesthetic wooden panel are installed, you will have to adjust the door spring tension. Rotate the adjusting screw to drive the adjustor to strain or relax the steel cable(see figure 5). Door spring tension is correct when the door remains horizontal in the fully opened position,yet rises to a close with the slight lift of a finger.
● Dishwasher installation steps 1 Install the furniture door to the outer door of the dishwasher using the brackets provided. Refer to the template for positioning of the brackets. 2 Adjust the tension of the door springs by using an Allen key turning in a clockwise motion to tighten the left and right door springs. Failure to do this could cause damage to your dishwasher (Illustration 2) . 3 Connect the inlet hose to the cold water supply . 4 Connect the drain hose. Refer to diagram .
Dishwasher must be level for proper dish rack operation and wash performance. 1 Place level on door and rack track inside the tub as shown to check that the dishwasher is level. 2 level the dishwasher by adjusting the four leveling legs individually. 3 When level the dishwasher, pl ea s e pay attention not to let the dishwasher tip over. 【Figure 8】 Illustration of feet adjustment Check Level Front to Back NOTE: The maximum adjustment height of the feet is 20 mm.
In order to avoid that there is more water staying in the inlet hose, please close the hydrant after using.(For the models: no safety inlet hose.) Connect the cold water supply hose to a threaded 3/4(inch) connector and make sure that it is fastened tightly in place. If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that the water is clear and free of impurities.
Before Calling for Service Review the charts on the following pages may make you be free of calling for service. ' ' Fuse blown, or the circuit breaker acted Replace fuse or reset circuit breaker. Remove any other appliances sharing the same circuit with the dishwasher Power supply is not turned on Make sure the dishwasher is turned on and the door is closed securely. Make sure the power cord is properly plugged into the wall socket.
Combination of soft water and too much detergent Use less detergent if you have soft water and select a shortest cycle to wash the glassware and to get them clean. Tea or coffee stains using a solution of 1/2 cup of bleach and 3 cups warm water to remove the stains by hand. You have to wait for 20 minutes after a cycle to let the heating elements cool down before cleaning interior; otherwise, burns will happen.
Technical data Type : ZIM 427 Weight gross(kg) 41 Nr of programs 7 Height(cm) 82 Energy class( * ) A Width(cm) 44.5 0.74 Depth(cm) 54 Energy consumption(kWh/cycle)( ** ) Wasshing efficiency A Depth with opened door(cm) 115 Drying efficiency A Hot water connection <60 Loading Capacity(Place settings) 8 Water Pressure Range(kPa) Water consumption(l/cycle) 13 Voltage(V) Noise level(dB(A)/re1pW) 49 Connected value(kW) Weight net(kg) 36 Fuse(A) 0.04-1.