Contents 1 Safety Precautions ............................................................................................... 4 2 INTRODUCTION..................................................................................................... 5 3 FEATURES .............................................................................................................. 6 4 Quick Start Guide.................................................................................................. 7 4.1 Front Panel.......
Contents 7.1 Changing Group ....................................................................................................................27 7.2 Find channel ..........................................................................................................................28 7.3 EPG now/next list ..................................................................................................................28 7.4 Switch EPG between now/next ....................................................
Contents 14.1 Youtube ................................................................................................................................51 14.2 Shoutcast .............................................................................................................................52 14.3 Picasa ...................................................................................................................................53 14.4 RSS..............................................................
About 1 Safety Precautions CAUTION: The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to "dangerous voltage" and to prevent from a risk of electric shock. Warning: To reduce the risk of electric shock, don't open the cabinet. Refer servicing to qualified personnel only. The exclamation point within an equilateral triangle is intended to alert the user to important operating and maintenance (servicing).
About Note: Moisture may be formed on the lens In the following conditions: when the unit is suddenly moved from a cold environment or an air-condition room to a warm place. immediately after a heater has been turned on. in a steamy or very humid room. If the moisture forms inside the unit, it may not operate properly. To correct this problem, turn on the power and wait about two hours for the moisture to evaporate.
About 3 FEATURES MPEG-Fully DVB-S / DVB-S2 HD compliant DVB-T/DVB-C (optional) Endless channels (TV and Radio) programmable Multilingual menu text support Channel list editing Favourite channel list editing True-color On-Screen Display (OSD) Full Picture In Graphic (PIG) function Electronic Program Guide (EPG) for on screen channel information Subtitle supported Teletext supported by software emulation Parental lock facility by channel and pro
Basic Operations 4 Quick Start Guide 4.1 Front Panel Open the hand flap on the front panel. Hold Smartcard horizontally with the electronic chip facing upwards. Then insert the Smartcard into the slot.
Basic Operations 4.2 Rear Panel 4.3 Connections This section describes how to connect your product to match your particular devices setup and to gain optimum signal quality. The product provides various interfaces to connect to the TV, VCR or other devices. Select the most appropriate depending on the device you have. Warning: Connect all components before plugging any power cords into the wall outlet. Always turn off the product, TV and other components before you connect or disconnect any cables.
Basic Operations 4.3.1 Connecting the Antenna 1. Connect one or two satellite coaxial cable from the wall to LNB IN. 2. Connect a cable/terrestrial coaxial cable to AERIAL IN. Note: Cable and terrestrial can't concurrence. 4.3.2 Connecting the TV 1. 2. 3. TV with the HDMI connector: For the best picture quality, connect the product and TV using an HDMI cable. TV with the SCART connector: For good picture quality, connect the product and TV using a SCART cable.
Basic Operations and enhance your viewing enjoyment. 4.3.3 Connecting the Network 1. 2. a. b. 3. Connecting to the LAN: Connect one end of the Ethernet cable to the product and the other end to the LAN router. Connecting to the Wi-Fi (Wireless LAN): You can connect the network via the Wi-Fi access point or DSL/cable modem. Plug in the wireless USB dongle to the USB port.(Separate purchase required) Set the options for the Wi-Fi.
Basic Operations 4.4 Powering On/Off 1. 2. 3. Connect the power cord of the product to a wall outlet. Turn on the power switch of the rear panel. Power on/off by pressing the [ POWER] button on the remote control or [ POWER] button on the front panel. ? Frequently Asked Question Q: The power of my STB has been turned on and not in Standby mode, but the TV screen showed nothing: A: Make sure the TV set has been set to the correct video input (not the TV channels).
Basic Operations 4.5 Remote Control You can power on/off the receiver, operate on screen menu, and use a variety of hot key function. POWER To switch your receiver on from standby or standby to on. MUTE Used to enable or disable the audio NUMERIC KEYS Used to select channels or enter programming parameters TV / RADIO Receiver switches between TV and Radio mode. (ZOOM) Press key select zoom times, from X1 to X16. (RECALL) Return to the previous menu or status.
Basic Operations To start the recording. TXT Shows teletext or subtitle information of the current channel supports. OPTION Shows NVOD information of the current channel supports. Blue Button Into the multi-screen function in full screen. (FIND) Use to prompt find channels sort by character. SLEEP Press timer key you can setup up the Standby time. V.FORMAT Press V.FORMAT button to switch the display mode among "Auto", "480", "576”,” 720”,” 1080I" and "1080P".
Networking 4.6 Easy Install This menu to help you set basic function quickly. When the STB is first used, there will show the Easy Install menu. When you used the Factory Reset function in System/Basic Setting/Factory Default menu, it also will show the Easy Install menu after reboot. Note: If the software has default channel list, the STB will play the first channel in the list. 4.6.1 Language Setting Language setting allows you to select the main language.
Networking option, press [ok] button, then press [▲▼ , ] buttons, at last press [ok] button. Or press [◄, ►] buttons to select ON . If not DHCP service, you need select OFF, you need config the network by manual. In this menu: Press [P+] button to go to the Video Setting menu. Press [P-] button to go to the Time Setting menu. 3. Conversion: Press [◄, ►] buttons to switch the manner circularly by the sequence “ LETTER_BOX<-> PAN_SCAN<-> COMBINED<-> IGNORE.
Networking Software Upgrade Notify: Press[◄, ►] buttons to switch it between Enable and Disable. Resource Transfer Mode: Press [◄, ►] buttons to switch it between HTTP and FTP. Note: Press the [TV/RADIO] button to switch between TV and radio channels. Press the [RECALL] button to return to the previous ten channels. 4.7 SCAN CHANNEL Go to menu/Install/Satellite Install/Satellite, select an appropriate satellite and then press [red] button to scan channels.
Networking Each time you press this button, the value changes. 480<-> 576<-> 720<-> 1080i<->1080p<-> Auto Note: When you connect with A/V or SCART, the TV has output that only you change to resolution the TV supports. 5.5 Info bar The info bar is display informations about the channel of the time whenever you change channels. Press the [INFO] button while it hide. Press the [EXIT] button to hide. Note: It not displayed when not channels. 5.
Networking 5.10 NVOD Press [OPTION] button in full screen, it display NVOD menu if it has NVOD. Or it will show "no option channel". 5.12 Subtitle 5.11 Teletext Teletext is a free service broadcast which gives the latest information on news, weather and many other topics. You can use interactive services in teletext mode. All teletext supporting channels have the TTX icon display highlight on the info bar. 1. Press [TTX] button and select TTX. 2. Press [▲, ▼] button to select the language. 3.
Networking 5.13 Quick bar Press [F1] button to display the menu. It show weather message, time and state of NET and USB, and has shortcut to enter to "weather" menu. It also has message box and manage of USB memory. Message box is show the system message, like notify of the new software. 5.15 Change Satellite 1. 2. 3. Press [SAT] button. Press [▲, ▼] buttons to select Satellite. Press [ok] button. 5.16 Change Favourites group 1. 2. 5.14 Manage of USB memory 3. Press [FAV] button.
Networking 1. 2. 3. Press [REC] button to start recording. Press [REC] button again to pause recording. Press [PLAY MODED] button to enter into Record menu. 4. Press [▲, ▼] buttons to select an option. 5. Press [ok] button to enter into Record Edit menu. 6. Press [◄, ►] buttons to change the duration. 7. Press [STOP] button to stop recording. Note: 1. Now it support two recordings. 2. You can record radio programmes also. 3. The record banner will be display whenever pressing [INFO] button. 4.
Networking 5.18 Play the recorded file when it recording 1. Press [PLAY] button to start play the recorded file. 2. Press [PAUSE] button to pause play. 3. Press [◄, ►] buttons to jump the playing place. 4. Press [PAGE-, PAGE+] button to play fast. 5. Press [PREV/NEXT] button to jump the head/end of the file. 6. Press [STOP] button to stop play. 5.20 Unmount USB Disk 1. 2. 3. 4. Press [PLAY MODE] button. Press [▲, ▼] buttons to select the disk. Press [ok] button. Select YES and press [ok] button 5.
Networking 6.1.2 Changing group You can display the list of the selected channel group. (All, FAV, Satellite, A-Z, Provider, CAS, HD, Broadcaster.) 1. 2. Press [▲, ▼] buttons. Select a channel group. 6 Channel 6.1 TV/Radio list The channel list will help you find the channel you want to watch or edit quickly and easily. You can access the channel list in several ways. In full screen, press [ok] button the list will show in mid. Note: Can only operate for one channel. 6.1.
Networking 2. Select FAV and press [ok] button. 3. Select FAV groups that you want. 4. Press [EXIT] to save and exit. Note: Do it again to cancel the favourite channel 6.1.4 Sorting channels Sort the list by: Number, A-Z, Free+CAS, CAS+Free, TP 1. Press [blue] button. 2. Press [▲, ▼] buttons to select an option. 3. Press [ok] button. 6.1.5 Watch EPG 1. 2. 6.1.7 Skipped channel/Cancel skip channel You can't watch this channels with [▲ ,▼ ] button in full screen. 1. Press [yellow] button. 2.
Networking save and exit. Delete: Press [ok] button, and Press [ok] to save and exit. Rename: Press [ok] button and enter the name in the keyword, then press [red] to save and exit. Note: Cancel lock need input password.(If you not change the password is 0000) Note: 1. Press [green] button to move cursor preceding. 2. Press [yellow] button to move cursor next. 3. Press [blue] button to clear the keyword. 6.2 Managing Channels 6.2.
Networking 6.2.1.1 Changing group You can display the list of the selected channel group. All, FAV, Satellite, A-Z, Provider, CAS, HD, Broadcaster. 1. Press [red] button. 2. Press [▲, ▼] buttons, select a channel group. 3. Press [ok] button. 6.2.1.2 Selecting channel You can using [ok] button to select one by one, or select channel quickly by option menu, Select All, Unselect All, Select Others, Select TP, Provider 1. Press [green] button. 2. Press [▲, ▼] buttons, select a channel group. 3.
Networking 6.2.1.5 Display channel detail information You can display the information menu to know the information, service, satellite, TP, vid/aud pid, Pcr/pmt pid, service id, Frame Status, Provider CAS about the channel. 1. Press [▲, ▼] buttons to select a channel. 2. Press [INFO] button. And press again to cancel. 6.2.2 Organizing Favourites 6.2.1.6 Find channel Find channel in currently group. 1. Press [FIND] button. 2. Input channel name to keyword. 3. Press [red] to confirm. Note: 1.
Networking Note: 1. When you cancel favourite channels, you can only using [ok] to select. 2. All favourite channels in the right column. 7 EPG 6.2.2.2 Renaming for FAV group 1. Press [►] or [◄] button. 2. Select Rename. 3. Press [ok] button to input the name in keyword. 4. Press [red] button. Note: 1. Press [green] button to move cursor preceding. 2. Press [yellow] button to move cursor next. 3. Press [blue] button to clear the keyword. 6.2.2.3 Moving favourite channels 1. Press [◄] button. 2.
Networking 7.2 Find channel Find channel in currently group. 1. Press [FIND] button. 2. Input channel name to keyword. 3. Press [red] to confirm. Note: 1. Press [green] button to move cursor preceding. 2. Press [yellow] button to move cursor next. 3. Press [blue] button to clear the keyword. 4. Press [white] button to switch the input mode. 7.4 Switch EPG between now/next There are two ways to switch EPG now and next list. Press [◄, ►] buttons to switch the list EPG between now and next. 1.
Networking Go to menu/channel menu, then select Organizing Timer or in EPG menu press [yellow] button. 7. 8. 9. number keys to change it. Stop time: Show end time of event, you can press number keys to change it. Repeat: Show the event transact times, press [◄, ►] keys to switch among once, everyday, a week, workday, weekend. Timer mode: Type of the event, it has change service and HDD record. 7.8 Editing a timer affair 7.7 Adding a new timer 1. 2. 3. 4. Press [yellow] button to go to Timer menu.
Networking You can either connect to two antenna with a single LNB switch using an RF cable. 8.1.3 Using LNB Switch Only 8.1.2 DiSEqC You can either connect to several antennas with a LNB switch using RF cable. You can search only channels of one or two satellite using the fixed antenna. 1. Check that your antenna connection and the selected antenna type are correct. 2. Select a satellite figure and press the [green] button. Satellite: Select the satellite.
Networking 1. All: Scan all type channels it can find. 2. FTA: Scan free channels. 3. ALL_TV: Scan all TV channels. 4. FTA_TV: Scan free TV channels. 5. ALL_RADIO: Scan all radio. 6. FTA_ RADIO: Scan free radio. Net: Select NIT ON to receive the latest transponder information. 4. Press [ok] button to scan. 5. When the search has completed, select save and press [ok] button to save the found channels and exit. Note: Press [EXIT] button to stop the channel search. information. 7.
Networking 3. 4. 5. Auto <–> 1/2 <-> 2/3 <-> 3/4 <-> 4/5 <-> 5/6 <-> 6/7<-> 7/8 <-> 8/9 <->1/4 <-> 1/3 <-> 2/5 <-> 3/5 <-> 9/10. Mode: Select the mode with DVB-S or DVB-S2. Press [ok] button. Press [yellow] button to edit the select transponder. Press [blue] button to delete the select transponders. Press [INFO] button to display the search channels of the transponder. 3. Refer to Setting Transponder for details in transponder setting. 8.1.7 Motor setting 8.1.
Networking 8.2 Search Cable Channels In auto installation: Press [ok] button to enter and it auto scanning channels. (optional) 8.3 Search Terrestrial Channels Go to menu/Install/Cable Install, you can search channels by manual or auto. Note: If the antenna is not properly set, channel search cannot be activated which means you cannot watch any of the programmes. (optional) In manual installation: 1. You can press [ok] button to select one or more TP and press [red] button to scan channels. 2.
Networking 9. Press [blue] button to delete the select transponders. 10. Press [INFO] button to display the search channels of the transponder. 1. Menu Language: Press [ok] button, then press [▲, ▼] buttons to select on option, at last press [ok] button. Or [◄, ►] buttons select an OSD menu language. 2. Audio Language: Press [ok] button, then press [▲, ▼] buttons to select on option, at last press [ok] button. Or [◄, ►] buttons select an audio language.
Networking on full screen. The supported language can be changed without any notice. 6. Teletext Language: Press [ok] button, then press [▲, ▼] buttons to select on option, at last press [ok] button. Or [◄, ►] buttons select the TXT language. As long as the services support it, the Teletext language is changeable by teletext menu on full screen. The supported language can be changed without any notice. 7.
Networking [ok] button. Or press [◄, ►] buttons to select an option. View all: Play channels not need password. 7, 12, 15, 18: those option determining that different stream, whether have to input password. Lock all: Play channels need input password. 3. Time Control: Press [ok] button, then press [▲, ▼] buttons to select on option, at last press [ok] button. Or press [◄, ►] buttons to select ON or OFF On: Play channels not need password only in Allow time. OFF: Play channels not need password at any time.
Networking 9.1.6 Miscellaneous Setting 1. 2. 9.1.5 Factory Default This menu is operating for database. 1. Load From Factory Default: Press [ok] button, it display a warn information, select "YES" to come back factory default. Note: If you do Save As Factory Default before, it will be back the database that you save. 2. Factory Reset: Press [ok] button, it display a warn information, select "YES" to come back factory default. 3.
Networking 9.1.7 Tuner Configuration 9.1.9 Contact This menu control Cable and Terrestrial tuner. Press [ok] button, then press [▲, ▼] buttons to select on option, at last press [ok] button. Or press [◄,►] buttons to select Cable or Terrestrial. Cable: The Install menu will display Cable Install menu, then you can scan cable channels. Terrestrial: The install menu will display Terrestrial Install menu, then you can scan Terrestrial channels. This menu is note the message of provider.
Networking Record Setting, Timeshift Setting and Youtuble Record Setting. 9.2.1 HDD Format The menu show the message about the USB disk. Format Disk: 1. Press [red] button and press [▲, ▼] buttons to select a format for the disk, then press [ok] button to start. This case can hold subarea 2. Press [green] button to enter into the menu: a. [green] button: Add a new subarea. b. [yellow] button: Delete a subarea. c. [red] button: Save and partition the disk. d. [blue] button: Format disk.
Networking 3. select WPA-PSK or WPA2-PSK, Encryption has TKIP and AES two options. Press [red] button to connect. 9.2.5 Youtuble Record Setting This menu include Enable and Record Path. Enable: Press [ok] button to select ON and OFF. Record Path: Press [ok] button to change the record path. 9.3 Net Setting 9.3.1 Configuring Wi-Fi (wireless) 1. 2. Select Wireless on Default Network Type item.
Networking 9.3.3 Dynamic Setting 9.3.5 Network hard disk Go to menu/system/IP config menu, press [green] button enter into setting DDNS menu. Dynamic Start: Press [ , ] buttons to select ON or OFF. User: Press [ok] button to input the user name. Password: Press [ok] button to input the password. Host: Press [ok] button to input the host domain name. Update Interval (Sec): Use number buttons to input the time. Setting those options, you can use network hard disk.
Networking 9.4 Upgrade 9.4.1 Upgrade from USB 1. Upgrade Type: Press [ok] button, then press [▲, ▼] buttons to select on option, at last press [ok] button. Or press [◄, ►] buttons to select an option. App, App + Plugin, App + Database + Plugin, Database, App + Database. 2. Folder: Press [ok] button to select correlative software. 3. Press [red] button to upgrade. 9.4.3 Backup system to HDD 1. Type: Press [ok] button, then press [▲, ▼] buttons to select on option, at last press [ok] button.
Networking in STB. 10 Conditional Access 11 Online The services of the menu all from online server. Receiver provide two CA slot for user to use. Receiver has build in smart card module with CONAX system. By using cards in this system provided by operators, it is possible to watch many scrambled channels coded in this system. This menu shows detailed information about card inserted into card reader module. It allows inserted according to help messages visible on the bottom of the screen.
Networking 1. 2. 3. Press [red] button Press [▲, ▼] buttons to select an option. Status, Address, Subject, timer Press [ok] button. 1. Press [green] button to enter into Add City menu. 2. Input the city name that you want, and press [red] button to confirm. Note: 1. You can only add five cities at most. 2. Press [▲, ▼] buttons to change city. 11.1.3 Delete message 1. Press [green] button to delete the selected message. 2. Press [yellow] button to delete all message of the list. 11.2.
Networking 11.2.5 Switch Date 11.4 User Manual Press [◄, ►] buttons to switch date. Note: It only display four dates weather in a city. 11.3 FAQ 11.3.1 Play the demo video 1. Press [◄, ►] buttons to switch frame. 2. Press [▲, ▼] buttons to change item. 3. Press [PLAY] or [ok] button to download and play the demo video. 11.4.1 Resource transfer mode is HTTP 1. 2. Press [◄, ►] and [▲, ▼] buttons to switch item. Press [ok] button at right column the picture, it begins to download and play the picture.
Networking 2. 3. Press [ok] button at right column, it begins to download the e-book list. Press [ok] button at right column, it begins to download and play the picture. 11.5.2 Resource transfer mode is FTP 11.4.5 Zoom the picture 1. Press [◄, ►] and [▲, ▼] buttons to switch item. 2. Press [ok] button at right column, it begins to download the entire e-book. 3. Press [ok] button at right column the picture, it begins to play the picture. When play the picture: 1.
Networking times. 2. Press [◄, ►] and [▲, ▼] buttons to move the zoom place. Note: Press [EXIT] button to cancel play. 7. Press [red] button to save and register. 11.6.2 Clear online data Press [yellow] button and select YES, then press [ok] button to confirm. Note: After do this the STB will reboot. 11.6 Config This menu use to register online server and config online. 11.6.1 Register 1. Name: Press [ok] button to enter into Name Modification menu, and input the name. 2.
Networking 12 File List 12.2 Sort files/Sort folder Enter into this menu has two ways. Go to menu/File list. In full screen, Press [FOLDER] button. In the list, press [green] button, then press [▲, ▼] buttons to select an option, at last press [ok] button. Name, Type, Size, Modify date. 12.1 Switch File list 12.3 Delete files/Delete folder There are two ways to switch file list. 1. Go to menu/File list menu, press [◄, ►] buttons to select one icon, then press [ok] button to enter into the list.
Networking 3. Press [PAUSE] button to pause play. 4. Press [◄, ►] buttons to jump the playing place. 5. Press [PAGE-, PAGE+] buttons to play fast. 6. Press [PREV/NEXT] button to jump the head/end of the file. 7. Press [PLAY MODE] button to select one mode. : Order and play the all selected files, then exit. : Circular play current file. 12.6 Online Subtitle : Circular play all selected files. 8. Press [STOP] or [EXIT] button to stop play. 12.5 Play Picture 1.
Networking Note: The size between 30% and 200%. 12.7 Setting Subtitle When play a movie file, the info bar hide, press [yellow] button to enter into Subtitle menu: Subtitle: press [ok] button, and then press [▲, ▼] buttons to select ON or OFF, at last press [ok] button. Or press [◄, ►] buttons to select ON or OFF. ON: Allow to display the downloaded subtitle. OFF: Can’t display subtitle. Note: if it select OFF, the other options can’t edit.
Networking 13 Plug In This menu is allows user install software by self. It supports the number of software by the hardware. It only has a calculating at first. 13.1 Using the calculating 1. 2. 3. 4. 5. Press [ok] button to start the function. Press [green] button to enter into menu. Press number buttons to input. Press color and [INFO] buttons to input operator. Press [EPG] button to clear the input. 14.1.1 Play the video 1. Press [ok] button to connect and display the list. 2.
Networking 14.1.2 Sort for the list 1. 2. Press [green] button. Press [▲, ▼] buttons to select Site or Duration. Site: it includes Germany, Worldwide, Poland and so on. Duration: it includes All Time, This Week, This Month and so on highlight video. 14.1.6 Download the video 1. Go to the System->PVR/HDD Setting->Youtube Record Setting menu to set the path of the file save. 2. Press [RECORD] button to start downloading the video file. 3. Press [FOLDER] button to enter into the downloading list. 14.
Networking 3. Press [red] button to confirm and find 14.2.2 Select Genre 1. 2. 3. Press [red] button. Press [▲, ▼] buttons to select an option. Press [ok] button. 14.3 Picasa This menu is picture in www.picasa.com 14.2.3 Add to Favorites 1. Press [▲, ▼] buttons to select. 2. Press [yellow] button Note: Press [green] button to switch favorites list. 14.3.1 Display the picture 14.2.4 Find radio 1. 2. 1. Press [▲, ▼] and [◄, ►] buttons to select one picture. 2. Press [ok] button 3.
Networking 14.3.2 Display the user’s album 14.4.2 Delete subscription Press [green] button to show the user’s album of the highlight picture. Press [green] button and then select YES, at last press [ok] button. 14.3.3 Display the album Press [yellow] button to display the album of the highlight picture. 14.4 RSS This menu is display RSS web. 14.4.3 Edit 1. 2. 3. Press [yellow] button. Press [▲, ▼] buttons to select Name or URL.
Networking 3. Press [ok] button to display detail information. 4. If it has several pages, press [P+/P-] buttons to display anterior or next page. 14.6 FTP Client This menu use to download file from FTP server 14.6.1 Switch Group When the cursor is on the left column: 1. Press [red] button. 2. Press [▲, ▼] buttons to select Browse Server, Downloading List or Downloaded List. 3. Press [ok] button. 14.4.5 Sort the news list 1. 2. 3. In the list, press [red] button.
Networking 14.6.3 Setting downloading files number at the same time When the cursor is on the left column: 1. Press [yellow] button. 2. Press [▲, ▼] buttons to select 1, 2 or 3. 3. Press [ok] button. 14.6.4 Display the information about the downloading / downloaded file In the Downloading List or Downloaded List, there are two ways to display the information. When the cursor is on the left column: 14.6.5 Add/Edit server Go to menu/download menu 1. Press [►] button. 2.
Networking 14.6.6 Delete Servers 14.6.9 Add Downloading File 1. Press [ok] and [▲, ▼] buttons to select servers. 2. Press [►] button. 3. Press [▲, ▼] buttons to select Delete, and select YES. 1. Connect server. 2. Press [▲, ▼] buttons to select a file. 3. Press [►] button. 4. Press [▲, ▼] buttons to select Download, and then press [ok] button. Source File URL: Display the source file URL. Rename: Press [ok] button to enter into Rename menu, and then input the name.
Networking . 14.6.11 Make Stopping Download files to Start In the Downloading List: 1. Select the stopping files. 2. Press [►] button. 3. Press [▲, ▼] buttons to select Start. 4. Press [ok] button. 14.7.1 Login 1. 2. 3. Press [menu] button. Input User Name and Password. Press [green] button to save and login. 14.6.12 Delete files In the Downloading List or Downloaded List: 1. Select the files that you want delete. 2. Press [►] button. 3. Press [▲, ▼] buttons to select Delete. 4.
Networking 3. Press [ok] button to confirm. 15.1 Setting Language 1. Press [ok] button to enter into Spark Portal menu. 2. Press [ ►] button to select Setting. 3. Press [◄, ►] and [ok] buttons to select one or more language. 4. Press [◄, ►] and [▲, ▼] buttons to select OK button . 5. Press [ok] button to affirm and exit. 14.7.4 Switch Date/Type Press [◄, ►] buttons to switch date/type. 14.7.5 Display the information at VOD list. Press [INFO] button to display the information about the video. 15.
Networking In Spark Portal menu: 1. Press [◄, ►] and [▲▼ , ] buttons to select one point. 2. Press [ok] button. 15.6 Navigation Menu 1. Press [MENU] button to display the navigation menu. 15.3 Remove App 2. Press icon to display the default internet point. 3. Press icon to display a browser, you can use it like IE. In Spark App Store menu: 1. Press [◄, ►] and [▲▼ , ] buttons to select one point that you are added. 2. Press [ok] button to enter. , ▼ ] buttons to select Remove from 3.
Addenda 16 Trouble Shooting If you suspect there is a fault with your receiver, please check the following trouble shooting guide before calling authorized service agent. Warning! Under no circumstances attempt to repair the receiver yourself. Tampering with the receiver may result in fatal electric shock and will invalidate your warranty.
Addenda 17 Specifications SYSTEM RESOURCES Main Processor 450M Hz based CPU Flash Memory Nor flash:8MB X 1 ; Nand flash:512MB X 1 DDR SDRAM DDR2 128MB x 2 Tuner/Front-end(Optional) Tuner Type DVB-S / DVB-S2 Input Connector F-type, Connector, Female Loop Through F-type, Connector, Female Signal Level -65 to -25 dBm LNB Power & Polarization Vertical: +13V/+14V Horizontal: +18V/+19V Current: Max. 500mA Overload Protection 22KHz Tone Frequency: 22±1KHz DiSEqC Control Amplitude: 0.6±0.
Addenda USB HDMI USB 2.0 slot Compatible for Host VER1.2 Type A PHYSICAL SPECIFICATION Size[W*H*D] 300mm*64mm*231mm Net Weight 1.