350 & 1450 AMMCO Brake Washer Systems Installation and Operating Instructions With Safety and Maintenance Instructions and Parts Identification READ these instructions before placing unit in service. KEEP these and other materials delivered with the unit in a binder near the machine for ease of reference by supervisors and operators. Manual Part No.: 629708 Revision Date: 09/08 rev. 09 1601 J. P. Hennessy Drive, LaVergne, TN USA 37086 615/641-7533 800/688-6359 HENNESSY INDUSTRIES INC.
ii • AMMCO 1350/1450 Brake Washer Systems
These instructions are for the AMMCO Model 1350 Portable Brake Washer and the AMMCO Model 1450 Deluxe Brake Washer. Refer to the parts list for identification. Table of Contents Tools required for Assembly Before You Begin Receiving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 ⁄8", 7⁄16", 1⁄2", & 9⁄16" Wrenches Straight Blade Screwdriver 3 Assembly Tool List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Assembly, 1450 . . . . . . . . . . . . . . . . . . . . . . . .
ASSEMBLY MODEL 1450 DELUXE BRAKE WASHER 18. Insert (2) long hose ends of “Y” assembly through holes in side of pan assembly. 1. Turn base and barrel assembly upside down. 19. Screw gun assemblies on the ends of “Y” hose assembly. 2. Align caster bracket holes with holes in base. 3. Use the 5⁄16" screws and nuts to attach casters to base. 4. Turn base and barrel assembly right side up. 5. Attach water filter bracket to outside of barrel using 1⁄4" screws, washers, and nuts.
OPERATION DRUM BRAKES NOTE: DO NOT ADD AIR TOOL OIL OR OTHER OILS TO AIR INLET OF WASHER. UNIT IS EQUIPPED WITH A COALESCING FILTER TO CLEAN AIR SUPPLY OF ANY OIL. OILS COULD DAMAGE THE AIR PUMP AND WILL VOID THE WARRANTY. 1. Before loosening or removing drum, use the flex spout to wet the inside of the drum and brake assembly; first, between the drum and backing plate. Then, if the vehicle had adjustment slots; remove the plug and insert the flex spout to wet the inside. 1. Connect shop air to washer.
MAINTENANCE NOTE: USE ONLY ORIGINAL AMMCO PRODUCTS FOR YOU SAFETY AND TO ENSURE COMPLIANCE TO O.S.H.A REGULATIONS. DISPOSAL OF FILTERS AND CLEANING SOLUTION The AMMCO 1350 and 1450 Brake Washers have been designed to comply with federal, state, and local regulations concerning the disposal of liquid and solid wastes. However, these regulations do vary from place-to-place and it is the shop owner/manager’s responsibility to comply with all applicable regulations.
MAINTENANCE continued from previous page… CLEANING BRUSH When brush gets dirty from brake fluid, axle grease, etc.; clean brush with a degreaser or solvent. Clean brush in solvent tank, NOT in brake washer. To prolong brush life and to decrease maintenance, use a shop rag for removal of heavy grease deposits. OIL BOOM The oil boom absorbs oil and lubricants but not water. Wring out boom into waste oil tank monthly. The boom can be re-used until it will not float.
6 • AMMCO 1350/1450 Brake Washer Systems
ITEM # 1 2 3 4 5 6 7 7 8 9 10 11 12 13 14 14 16 17 18 19 20 *21 *22 *23 24 *25 *26 PART # 629699 6182178 6109503 629704 629725 62968903 629764 629724 604507 604789 629795 629718 629700 640159 629701 629732 8301534 620531 629737 629751 629728 629702 629710 625456 95000138 629818 640160 1350 1450 QTY. QTY. DESCRIPTION Caster Nut, 5⁄16-18 Whiz Lock Screw, 5⁄16-18 X 3⁄4 Hex Support, Caster Base/Barrel Assy. Ring, Clamp Pan Assembly Pan Assembly Screw, #10 - 24 X .5" Rd. Hd. Mach.
Product In 33 Ship Unassembled 10 36 23 11 20 10 13 8 • AMMCO 1350/1450 Brake Washer Systems 10 3
ITEM # PART # 1 2 3 4 6 7 8 9 10 11 *12 629711 625953 629712 629717 629694 629819 629696 629697 8101428 625952 629706 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 *28 29 *31 32 33 36 95000138 629799 629729 62971402 62971401 62971301 62971302 62971303 62971304 62971305 62971308 629743 629756 629761 629762 629784 62971307 629735 6296962 6296961 95000133 1350 1450 QTY. QTY.
629708 09 04/08 © COPYRIGHT 1994 HENNESSY INDUSTRIES AND AMMCO TOOLS ALL RIGHTS RESERVED PRINTED IN U.S.A.
