User Manual

ManualsBrandsAMP Research ManualsAutomotiveAMP Research 76151-01A Black Running Board (PowerStep Plug N' Play System for Ford F-150)

www.amp-research.com

1/9

IM76151 rev 05.04.16

I N S T A L L A T I O N G U I D E

APPLICATION LENGTH MODEL YR PART #

Ford F150 SuperCab 72”’ 2015 76151-01A

Ford F150 SuperCrew 85” 2015 76151-01A

Invented, engineered and manufactured exclusively by AMP Research in the USA. May be covered by one of the following patents:

Printed in USA.

TOOLS REQUIRED

q Safety goggles

q 10 mm socket

q 13 mm socket

q 13 mm end wrench

q Ratchet wrench and extension

q Wire stripper

q 9/32” & 19/64” Drill Bit

q 3/16” hex key wrench ( allen wrench)

q 4mm hex key wrench ( allen wrench)

q Electrical tape

q Weather proof caulking ( silicone

sealer )

INSTALLATION TIME

2 3

SKILL LEVEL

4= Experienced

AMP RESEARCH TECH SUPPORT 1-888-983-2204 (Press 2)

Monday - Friday, 6:00 AM - 5:00 PM PST

2-3 Hours

Professional installation recommended

5-Year Limited Warranty

WARRANTY

Summary of content (10 pages)

PAGE 1
INSTALLATION GUIDE APPLICATION Ford F150 SuperCab Ford F150 SuperCrew LENGTH MODEL YR 72”’ 85” 2015 2015 PART # 76151-01A 76151-01A INSTALLATION TIME 2-3 Hours Professional installation recommended SKILL LEVEL 1 2 3 4 4= Experienced TOOLS REQUIRED q Safety goggles q 10 mm socket q 13 mm socket q 13 mm end wrench q Ratchet wrench and extension q Wire stripper q 9/32” & 19/64” Drill Bit q 3/16” hex key wrench ( allen wrench) q4 mm hex key wrench ( allen wrench) q Electrical ta
PAGE 2
A M P R E S E A R C H P O W E R S T E P TM – F O R D F - 1 5 0 INSTALLATION GUIDE Attaching motor to linkage assembly The motors must be attached to the linkage assemblies before continuing the installation process. Exploded View 19-03129-11 Motor 19-03179-90 Socket cap screw 19-03133-90 Washer CAUTION: HANDLE WITH CARE. To insure our customers receive all components with full integrity, we pack the motors separate from their linkage assemblies.
PAGE 3
A M P R E S E A R C H P O W E R S T E P TM – F O R D F - 1 5 0 Note: Some Applications require modification. Application Regular Cab Super Cab Super Crew Cut Length 55” (Trim 30”) 72” (Trim 13”) 85” (No Modification Required) Cut dimension 1 (A) End cap left (x1) (B) End cap right (x1) (C) T-nut insert (x2) (D) Socket cap screw (x2) (E) Nut plate (x2) x2 Running board assembly 3 2 x2 Motor linkage assembly x2 Idler linkage assembly 4 Wire harness www.amp-research.
PAGE 4
A M P R E S E A R C H P O W E R S T E P TM – F O R D F - 1 5 0 PARTS LIST AND HARDWARE IDENTIFICATION 8 7 x12 Nut with Conical Washer x8 Socket cap screw 10 11 x2 14 x4 Grommet 18 12 x6 M5 Socket Cap Screw Motor 15 x8 M5 Washer www.amp-research.com Grommet (Only needed on SuperCab and Regular cab models) x2 Gear Cover 16 x20 Cable Ties 7” Butt Connector x6 9 13 x4 LED Light 17 x2 Cable Ties 11” 19 ODB II Plug FD15 /9 IM76151 rev 05.04.
PAGE 5
A M P R E S E A R C H P O W E R S T E P TM – F O R D F - 1 5 0 Locate mounting points; first and last set of studs on the inner sill. Motor Linkage mounts toward the front of the truck and Idller mount toward the rear. Driver side shown below. 1 Driver Side Front Stud Location Driver Side Rear Stud Location Mount drive and Idler linkage assemblies. Repeat for passenger side. Make sure linkages sit square, fully resting on studs before tightening. Torque to 16 ft.
PAGE 6
A M P R E S E A R C H P O W E R S T E P TM – F O R D F - 1 5 0 Connect red and black power leads to battery. Red lead goes to positive. Route shorter leg of harness down passenger-side wheel well and longer leg of harness down along driver side wheel well. Secure with tie wraps. Remove fuse from wire harness 4 5 4 Attach wire harness to controller (make sure connector locking tabs fully engage). Mount controller with the two 11” tie wraps to factory conduit, just forward of battery.
PAGE 7
A M P R E S E A R C H P O W E R S T E P TM – F O R D F - 1 5 0 OBD II install: Use Supplied Posi Twist connectors to attach the Plug and Play Module to the Harness. Attach matching colors on the harness to the wires on the module. Plug in module to OBD II port on the vehicle. Secure harness with supplied tie wraps.
PAGE 8
A M P R E S E A R C H P O W E R S T E P TM – F O R D F - 1 5 0 On each side of the vehicle measure from the rear linkage to end of the board. Measurement should be approximately 11” as shown below. Attach step, sliding the mounting T-nut into position. Torque to 10 ft lbs (13.5 Nm) 1 12 18 2 3 4 5 6 7 8 9 11 10 13 19 On each side of the vehicle use tape to mark the led drill location two sections from studs as shown below. Use tape to indicate.
PAGE 9
A M P R E S E A R C H P O W E R S T E P TM – F O R D F - 1 5 0 Close and wrap with conduit and electrical tape. Secure all loose wires with cable ties with lamp wires pulled upward to avoid any wire snagging. Using supplied butt connectors, connect the lamp wires. Red to Red, Black to Black. Heat the shrink tubing on the connecters to seal wires. 17 Shrink Tubing 18 17 Replace fuse. 4 FINAL SYSTEM CHECK Check that all doors activate the PowerStep and the LED lights work when doors open and close.
PAGE 10
™ Congratulations on your purchase of the genuine AMP Research PowerStep! Here’s what you should know... AMP Research PowerStep running boards automatically move when the doors are opened to assist entering and exiting the vehicle. Automatic power deploy: The running boards will extend down and out when the doors are opened. Automatic power stow: The running boards will return to the stowed position when the doors are closed.