Owners manual

ManualsBrandsAMP ManualsAutomotiveResearch 76154-01A PowerStep Running Board With Plug And Play

www.amp-research.com

1/9

IM76154 rev 02.24.15

I N S T A L L A T I O N G U I D E

TOOLS REQUIRED

qSafety goggles

qMeasuring tape

qFlat blade screwdriver

qPower Drill

q9/32” drill bit

q13 mm socket

qRatchet wrench and extension

q13mm end wrench

qWire crimpers

qWire stripper / cutter

q3/16” hex key wrench (allen wrench)

q4mm hex key wrench ( allen wrench )

qElectrical tape

qWeather proof caulking (silicone sealer)

qSilicone spray

INSTALLATION TIME

2 3

SKILL LEVEL

4= Experienced

AMP RESEARCH TECH SUPPORT 1-888-983-2204 (Press 2)

Monday - Friday, 6:00 AM - 5:00 PM PST

2-3 Hours

Professional installation recommended

WARRANTY

5-Year Limited Warranty

Invented, engineered and manufactured exclusively by AMP Research in the USA. May be covered by one of the following patents:

Printed in USA.

APPLICATION AMP Part #

Chevrolet Silverado1500 / GMC Sierra 1500 - Double Cab * 2014-15 76154-01A

Chevrolet Silverado1500 / GMC Sierra 1500- Crew Cab 2014-15 76154-01A

Chevrolet Silverado HD / GMC Sierra HD - Double Cab *(excludes diesel engine) 2015 76154-01A

Chevrolet Silverado HD / GMC Sierra HD- Crew Cab (excludes diesel engine) 2015 76154-01A

*Modification required to running board assembly. See Item 1 on page 3.

Summary of content (9 pages)

PAGE 1
INSTALLATION GUIDE APPLICATION Chevrolet Silverado1500 / GMC Sierra 1500 - Double Cab * Chevrolet Silverado1500 / GMC Sierra 1500- Crew Cab Chevrolet Silverado HD / GMC Sierra HD - Double Cab *(excludes diesel engine) Chevrolet Silverado HD / GMC Sierra HD- Crew Cab (excludes diesel engine) AMP Part # 2014-15 2014-15 2015 2015 76154-01A 76154-01A 76154-01A 76154-01A *Modification required to running board assembly. See Item 1 on page 3.
PAGE 2
A M P R E S E A R C H P O W E R S T E P TM – C H E V R O L E T / G M C INSTALLATION GUIDE Attaching motor to Linkage assembly The motors must be attached to the Linkage assemblies before continuing the installation process. Exploded View 80-03129-90 Motor 19-03138-90 Gear Cover 19-03179-90 Socket cap screw 19-03133-90 Washer CAUTION: HANDLE WITH CARE. To ensure our customers receive all components with full integrity, we pack the motors separate from their Linkage assemblies.
PAGE 3
A M P R E S E A R C H P O W E R S T E P TM – C H E V R O L E T / G M C Note: Some Applications require modification.
PAGE 4
A M P R E S E A R C H P O W E R S T E P TM – C H E V R O L E T / G M C 10 x4 19-03608-90 Hex Bolt w Conical washer 15 x4 19-03467-90 U-nut 19 12 11 x4 x6 19-03356-90 19-03179-90 M5 Socket Cap Screw Nut w Conical washer 16 17 x20 19-02805-90 Cable tie (7”) x2 19-03339-90 Cable tie (11”) www.amp-research.
PAGE 5
A M P R E S E A R C H P O W E R S T E P TM – C H E V R O L E T / G M C Front Idler Linkage: Thread supplied bolt (10) in Install U Nut (18) into position just forward of brake cable T junction. Use supplied bolt (13) to about half way into the first sheetmetal tab / hole from front. Set linkage over bolt and Tighten lower bolt (10) hold Brake cable rod into position. to 16ft-lbs(22N m). Finger tighten nut (12) onto bolt (10). Install bolt (13) and torque to 16 ft-lb (22N m).
PAGE 6
A M P R E S E A R C H P O W E R S T E P TM – C H E V R O L E T / G M C Pull up front door sill plate covers as shown. Route long end of wire harness above engine and down through drivers side wheel well. Zip tie harness to cowling clips on fire wall. Route short end down passengers side. 4 3 2 1 8 6 7 Pull up the carpet and drill 9/32” hole in metal and insert supplied rubber grommet (21). Route wire harness along the frame and back towards 4 Secure with zip ties. Push both wires rear linkages.
PAGE 7
A M P R E S E A R C H P O W E R S T E P TM – C H E V R O L E T / G M C Using supplied butt connectors, connect the lamp Connect harness to motor. Secure harness with tie wires. Red to Red, Black to Black. Once Crimped use wraps. heat gun to shrink tube. Close and wrap conduit with electrical tape. Secure all loose wires with cable ties. Pull lamp wires upward to avoid any wire snagging.
PAGE 8
A M P R E S E A R C H P O W E R S T E P TM – C H E V R O L E T / G M C Reinstall fuse. Check that all doors activate the Power Step and the LED Lights work when doors open and close. Reinstall any remaining trim panels. 3 FINAL SYSTEM CHECK Check that all doors activate the PowerStep and the LED lights work when doors open and close. NORMAL OPERATION: When the doors open, PowerStep automatically deploys from under the vehicle.
PAGE 9
™ Congratulations on your purchase of the genuine AMP Research PowerStep! Here’s what you should know... AMP Research PowerStep running boards automatically move when the doors are opened to assist entering and exiting the vehicle. Automatic power deploy: The running boards will extend down and out when the doors are opened. Automatic power stow: The running boards will return to the stowed position when the doors are closed.