Users Manual

ManualsBrandsAMP ManualsElectrical EquipmentRF Receiver

Working temperature: -10º C ~ +50º C Radio Frequency: 433.925 MHz

Input Voltage: USB 5V 1A / USB 5V 2A Maximum Running Time: 6 minutes

Issues Possible Causes Solution

External battery pack is depleted

Recharge with compatible AC adaptor and check

connection and positioning of solar PV panel

Insufﬁcient charging from Solar

PV Panel

Check connection and orientation of solar PV panel

Remote control battery is discharged Replace battery

Battery is inserted incorrectly into

remote control

Check battery polarity

The motor is not responding Radio interference / shielding

Ensure remote control and the antenna on the motor are

positioned away from metal objects

Receiver is far away from Remote

Control

Move remote control to a closer position

Power failure Check power supply to motor is connected and active

Incorrect wiring

Check that wiring is connected correctly (refer to motor

installation instructions)

Always reserve an individual channel for programming

functions

SYSTEM BEST PRACTICE - Provide an extra 15 channel

remote in your multi-motor projects that provides

individual control for each motor for programming

purposes

Place all other motors into sleep mode (ref to P1 button

instructions)

Do not dispose of in general waste.

Please recycle batteries and damaged electrical products appropriately.

Cellular/Honeycomb

Standard

Cellular/Honeycomb

Skylight

Cannot program a single motor

(multiple motors respond)

Multiple motors are paired to the

same channel.

Settings Steps

1 Pairing P1 (hold down for 2s) > Stop (hold down for 2s)

2 Switch Rotating Direction Up + Down (hold down for 2s)

3 Setting Upper & Lower Limits

4 Add / Remove Favorite Position P2 > Stop > Stop

5 Roller Mode & Sheer Mode Switch Up + Down (hold down for 5s) > Stop

6 Adjust Limits

7 Pair / Unpair Additional Emitter P2 (existing) > P2 (existing) > P2 (new)

8 Speed Regulation

Upper Limit: Up (hold down for 2s) > Up + Stop (hold down for 2s)

Upper Limit: Up + Stop (hold down for 5s) > Up or Down > Up + Stop (hold down for 2s)

Acceleration: P2 > Up > Up

Lower Limit: Down (hold down for 2s) > Down + Stop (hold down for 2s)

Lower Limit: Down + Stop (hold down for 5s) > Up or Down > Down + Stop (hold down for 2s)

Deceleration: P2 > Down > Down

Please scan QR code to see more

AMP

™

product information

Motor 1 Connection Port

Motor 2 Connection Port

Charging Port

Switch

3%XWWRQ

System Overview

Motor 1 Connection Port

Motor 2 Connection Port

Switch

Charging Port

P1 Button

×× ×

Test Motor (Wakes and Runs)

Activate Pairing Mode

Sleep Mode

Reverse Motor 1 with Motor 2

Reset To Factory Settings

Approx. 2 sec.

Happening as you press for 2 seconds

Happening as you press for 1 second

Happening as you press for 6 seconds

Happening as you press for 10 seconds

Happening as you press for 14 seconds

Approx. 6 sec.

Approx. 10 sec.

Approx. 14 sec.

Until Shade:

Jog x3

Jog x4

Jog x1

Jog x2

Less than 1 sec.

Press P1

AMPTDBU RF Receiver

Declarations

Fields of Application

Specications

Quick Index

Attention

Safety Instructions

Troubleshooting

P1 Button Instructions

Never drop, knock, drill or submerge the motor.

Read all safety instructions before installation.

Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.

1. Do not expose motor to humid, damp, or extreme temperature conditions.

2. Do not drill into motor.

3. Do not cut the antenna. Keep it clear from metal objects.

4. Do not allow children to play with this device.

5. If the power cable or connector is damaged, do not use.

6. Ensure the correct crown and drive adaptor are used.

7. Ensure the power cable and aerial is clear and protected from moving parts.

8. Cable routed through walls should be properly isolated.

9. Motor is to be mounted in horizontal position only.

10. Before installation, remove unnecessary cords and disable equipment not needed for powered operation.

11. Installation and programming should be performed by a qualiﬁed professional. Use or modiﬁcation outside the

scope of these instructions may void warranty.

Switch Functions

1. When the Switch is at Location 1, it is Cellular/Honeycomb TDBU and Cellular/Honeycomb

Day/Night Shades working mode.

2. When the Switch move to Location ON, it is Cellular/Honeycomb Standard and Cellular/Honeycomb

Skylight working mode.

3. The Factory default mode is setting at Location 1.

U.S. Radio Frequency FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired

operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Any Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

ISED RSS Warning:

This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS

standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the

device. Le présent appareil est conforme aux CNR d’ISED applicables aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2)

l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible

d’en compromettre le fonctionnement.

Cellular/Honeycomb

TDBU

Cellular/Honeycomb

Day/Night

Summary of content (2 pages)

PAGE 1
AMPTDBU RF Receiver Declarations U.S. Radio Frequency FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
PAGE 2
3.2 Set Lower Limit Button Instructions Left Side Controls Bottom Rail a. Press Left “Down” button to lower the Bottom Rail, then press Left “Stop” button when it is in the desired lower limit. b. Press Right “Down” button to lower the Middle Rail, then press Right “Stop” button when it is in the desired lower limit. c. Press and hold (about 2 sec) Left “Down” and Left “Stop” buttons simultaneously until motor jog x2.