Owner’s Guide for the B2/B2R Bass Amplifier Made in the U.S.A.
B2/B2R Bass Amplifier TABLE OF CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Important Safeguards and Precautions . . . . . . . . . .3 The Front Panel Controls and Their Use . . . . . . . .4 The Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Some Suggested Settings . . . . . . . . . . . . . . . . . . .6 Rack Mounting (B2R only) . . . . . . . . . . . . . . . . . . .
B2/B2R Bass Amplifier Important Safeguards and Precautions All Ampeg products are designed for continuous, safe operation, as long as common sense is used and steps are taken to help avoid certain problems. Abiding by the following rules can help prevent damage to your amplifier, yourself and others. • The amplifier is equipped with a three-pronged AC power cord. To reduce the risk of electrical shock, NEVER remove or otherwise attempt to defeat the ground pin of the power cord.
B2/B2R Bass Amplifier The Front Panel Controls and Their Use 40Hz INPUT PAD GAIN BASS ULTRA MID TREBLE MASTER LIMITER 80Hz 150Hz 300Hz 600Hz 900Hz 2kHz 5kHz 8kHz POWER +12dB 0 -12dB 1 -15dB PEAK 2 3 LIMIT 4 5 1. 0dB (INPUT): The signal output from an instrument (active or passive) or a line level signal may be connected here by means of a shielded instrument cable. 2. 15dB PAD: This switch, when depressed, attenuates the input signal by 15dB.
B2/B2R Bass Amplifier The Rear Panel MODEL: B2R SERIAL: Q2ZZ650022 LINE: 120 V ~ 60 WATTS: MAX 14 15 16 14. FAN: This temperature controlled, variable speed fan draws cool air into the amplifier, which forces heat out through the exhaust vents. Never block the vent holes or the fan opening. 15. FUSE: This protects the unit from damage due to overload conditions or power line surges. If the fuse blows, replace it only with the same size and type. 16.
B2/B2R Bass Amplifier Some Suggested Settings The setting of the Gain control depends on your particular instrument. The Master should be set to produce the appropriate output volume level. The Graphic EQ can be used to tailor the amplifier to your speaker cabinets, to compensate for room acoustics and to “fine tune” your sound.
B2/B2R Bass Amplifier Troubleshooting In the unlikely event that your B2/B2R should malfunction, take a few minutes to troubleshoot it before you call for service. You can save yourself a lot of time and sometimes money by doing it yourself, and often the cure for the problem is something quite simple.
B2/B2R Bass Amplifier Technical Specifications OUTPUT POWER RATING 350 Watts RMS, 4 ohm load, 120VAC 200 Watts RMS, 8 ohm load, 120VAC POWER REQUIREMENTS Domestic: Export: 120VAC, 60Hz, 310VA 100/120VAC, 50/60Hz, 310VA 230-240VAC, 50/60Hz, 310VA TONE CONTROL RANGE Bass: Ultra Mid: Treble: ±8dB @ 50Hz ±8dB @ 500Hz +12dB/-19dB @ 5kHz GRAPHIC EQ RANGE 40Hz: 80Hz: 150Hz: 300Hz: 600Hz: 900Hz: 2kHz: 5kHz: 8kHz: GAIN SIGNAL TO NOISE RATIO INTERNAL SPEAKER (B2 ONLY) Size/Type: Magnet: Voice Coil: Impedance: