Owner's Guide for the SVT-GS Gene Simmons Punisher Bass Amplifier Made in the U.S.A.
SVT-GS Gene Simmons Punisher Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Important Safeguards and Precautions . . . . . . . . . .3 The Front Panel Controls and Their Use . . . . . . . .4 The Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Some Suggested Settings . . . . . . . . . . . . . . . . . . .6 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . .
SVT-GS Gene Simmons Punisher Important Safeguards and Precautions All Ampeg products are designed for continuous safe operation, as long as common sense is used and steps are taken to help avoid certain problems. Abiding by the following rules can help prevent damage to your amplifier, yourself and others. • The amplifier is equipped with a three-pronged AC power cord. To reduce the risk of electrical shock, NEVER remove or otherwise attempt to defeat the ground pin of the power cord.
SVT-GS Gene Simmons Punisher The Front Panel Controls and Their Use 1 2 3 4 5 6 7 1. INPUT: Connect your bass here using a standard shielded instrument cable. 2. 15dB PAD: When engaged, this switch cuts the input signal level by 15dB, allowing you to set the Gain control (#4) for the best signal to noise ratio. (If your bass has high-output pickups or active electronics, you should use the Pad.) 3. PEAK LED: This LED lights whenever any preamp stage is near clipping.
SVT-GS Gene Simmons Punisher The Rear Panel MODEL: SVT-GS SERIAL: SVTGS126902U LINE: 120 V ~ 60 Hz WATTS: MAX 115VAC, 60Hz: T10A SLO BLO 100/115VAC, 50/60Hz: T8A SLO BLO 230VAC, 50/60Hz: T4A SLO BLO 16 17 18 16. FAN: This temperature controlled, variable speed fan draws cool air into the amplifier, forcing heat out through the exhaust vents (also on the rear panel, between the speaker jacks and the power amp in jack). Never block the vent holes or the fan openings.
SVT-GS Gene Simmons Punisher Some Suggested Settings The setting of the Gain and Master controls depend on your bass, on your playing style, and on how loud you want it! The Graphic EQ can be used to compensate for room acoustics, to “fine tune” your sound, and as a “second channel” to be kicked in when needed for soloes and riffs.
SVT-GS Gene Simmons Punisher Troubleshooting In the unlikely event that your SVT-GS Gene Simmons Punisher should stop working properly (or just stop working), take a few minutes to troubleshoot it before you call for service. You can save yourself a lot of time and sometimes money by doing it yourself, and often the cure for the problem is something quite simple.
SVT-GS Gene Simmons Punisher Tech Specs OUTPUT POWER RATING 350 Watts RMS, 4 ohm load, 120VAC 200 Watts RMS, 8 ohm load, 120VAC POWER REQUIREMENTS Domestic: Export: 115VAC, 60Hz, 205VA 100/115VAC, 50/60Hz, 205VA 230VAC, 50/60Hz, 205VA TONE CONTROL RANGE Bass: Ultra Mid: Treble: ±8dB @ 50Hz ±8dB @ 500Hz +12dB/-19dB @ 5kHz GRAPHIC EQ RANGE 40Hz: ±11dB 80Hz: ±8dB 150Hz: ±8dB 300Hz: ±8dB 600Hz: ±8dB 900Hz: ±8dB 2kHz: ±8dB 5kHz: ±9dB 9kHz: ±12dB GAIN 45dB typical, tones @ center SIGNAL