Specifications

ManualsBrandsAmpeg ManualsMusical Instrument AmplifierSVT-5 PRO

Owners Guide for the

Ampeg

is Proudly Made in America

Bass Amplifier

+12dB

-12dB

LEVEL

+8dB

-10dB

MUTE

PEAK /

MUTE

BRT

-15dB

33Hz 9kHz5kHz2kHz900Hz600Hz300Hz150Hz80Hz

POWER

MASTER TUBE GAINTREBLEFREQUENCYMIDRANGEBASSGAININPUT

Ampeg

is Proudly Made in America

Summary of content (8 pages)

PAGE 1
Owners Owners Guide Guide for for the the Bass Amplifier 33Hz INPUT GAIN BASS HI BRT MIDRANGE FREQUENCY TREBLE MASTER TUBE GAIN +12dB 0 -15dB PEAK / MUTE LO 80Hz 150Hz 300Hz 600Hz 900Hz 2kHz 5kHz 9kHz +8dB POWER MUTE EQ -12dB ON LEVEL -10dB ON Ampeg ®® is Proudly Made in America
PAGE 2
SVT-3 PRO Bass Amplifier TABLE OF CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Important Safeguards and Precautions . . . . . . . . . .2 The Front Panel Controls and Their Use . . . . . . .3,4 The Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . .4,5 Some Suggested Settings . . . . . . . . . . . . . . . . . . .6 Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
SVT-3 PRO Bass Amplifier The Front Panel Controls and Their Use 33Hz INPUT GAIN BASS MIDRANGE FREQUENCY TREBLE MASTER TUBE GAIN 80Hz 150Hz 300Hz 600Hz 900Hz 2kHz 5kHz 9kHz +12dB +8dB 0 -15dB 1 2 34 EQ LO PEAK / MUTE 5 6 POWER MUTE HI BRT 7 8 9 10 11 12 LEVEL -12dB -10dB ON 13 14 15 16 1. INPUT: The signal output from an instrument (active or passive) or a line level signal may be connected here by means of a shielded instrument cable. 2.
PAGE 4
SVT-3 PRO Bass Amplifier The Front Panel Controls and Their Use plana en la posición central. 12. MAESTRO: Esto controla el nivel general de la salida del amplificador. Utilice este control junto con la Ganancia (#5). 13. GANANCIA DE BULBOS: El control de ganancia de los bulbos varía el suministro de voltaje alto a los bulbos del amplificador de potencia.
PAGE 5
SVT-3 PRO Bass Amplifier The Rear Panel output when the mute switch (#14) is engaged. This allows for silent tuning through an electronic tuner or killing the house send with a monitor mixer send still active. 29. FUSE: The fuse protects the unit from damage due to overload conditions or AC power line surges. If the fuse blows, replace it only with the same size and type. 30. AC LINE IN: Firmly insert the supplied AC power cord into this socket until it is fully seated.
PAGE 6
SVT-3 PRO Bass Amplifier Some Suggested Settings A Note About The Graphic EQ: The Graphic EQ can be used in two ways: 1) To fine tune your sound, make small adjustments at the desired frequencies and leave the EQ on throughout the entire session. (This is great for adapting to varying room acoustics when going from club to club, etc.); 2) For a completely different sound, make larger adjustments and only activate the EQ when you want a “second channel” sound (such as during bass solos).
PAGE 7
SVT-3 PRO Bass Amplifier Troubleshooting In the unlikely event that your SVT-3 PRO should malfunction, take a few minutes to troubleshoot it before you call for service. You can save yourself time and money by doing it yourself, and often the cure for the problem is something quite simple.
PAGE 8
SVT-3 PRO Bass Amplifier Technical Specifications OUTPUT POWER RATING 450 Watts RMS, 4 ohm load, 120VAC 275 Watts RMS, 8 ohm load, 120VAC TONE CONTROL RANGE Bass: Midrange: Treble: GRAPHIC EQ LEVEL GRAPHIC EQ RANGE 33Hz: 80Hz: 150Hz: 300Hz: 600Hz: 900Hz: 2kHz: 5kHz: 8kHz: BRIGHT SWITCH ULTRA HIGH SWITCH ULTRA LOW SWITCH ±12dB @ 50Hz ±15dB @ selected by Frequency control (220, 450, 800, 1.6k or 3kHz) +14dB/-19dB @ 5kHz ±10dB ±15dB ±8dB ±8dB ±8dB ±8dB ±8dB ±8dB ±9dB ±10dB +6dB @2kHz +6dB @ 5kHz +2.