Datasheet

ManualsBrandsAmphenol ICC ManualsConnectorsPower contact element male 20 A - Plug

CONTENT

DESCRIPTIONAPPLICATIONS

Hybrid D’Sub series

TW / E1

Amphenol D’Sub TW Hybrid Series permits

a mix of contacts including signal, power,

shielded, high voltage and fiber optics in the

same housing with 18 different contacts

arrangements.

This economic series was fist developed from

our military series, and has improved features:

- new contacts

- new high temperature black thermoplastic insert

- PCB configurations come preloaded with

fixed contacts and brackets.

These connectors are supplied with screw

machined contacts which are fixed in the insulator.

Acomplete range of housings are also

available for cable application.

• Commercial

• Medical

• Industrial

• Telecom

• Any application requiring

optimization of space

A full range of

arrangements

compatible with

reflow process

A full range of

arrangements

compatible with

reflow process

Specifications

• Connectors according to: MIL C24308 - NFC93425 - HE507

Materials and platings

Shells Steel-Tin plating

Insulators High temperature black thermoplastic

Signal contacts Female: machined bronze

Material Male: machined brass

Plating finish 16µ “Au over 79µ” Ni min.

Or 30µ” Au over 79µ” Ni min.

Shielded contacts Female: machined bronze

Material Male: machined brass

Plating

Inner conductor 16µ “Au or 30µm Au over 79µ” Ni

Outer ring 10µ “Au over 79µ” Ni

Terminations Tinned

Except solder cup and crimp terminations gold flash

Power contacts Female: machined bronze

Material Male: machined brass

Plating

Contacts 16µ “Au or 30µ” Au over 79µ” Ni

Terminations Tinned

Except solder cup and crimp terminations gold flash

Brackets Steel-Tin plating

Front jackscrews Brass-Tin plating

Rear clinch nuts Brass-Tin plating

Boardlocks Bronze-Tin plating

Stand-off Brass-Tin plating

Electrical Data

Current rating

Signal contacts 7.5 A. with 10 A. peaks

Power contacts

PCB terminations 10 to 40 A.

Solder cup terminations 10 to 40 A.

Crimp terminations 10 to 40 A.

Shielded contacts 0.5 A.

Voltage rating

Signal and power contacts 300 V.R.M.S. at 50 Hz

Shielded contacts 150 V.R.M.S. at 50 Hz

Shielded contacts

Frequency range 0-1 GHz

Attenuation 0.2dB

V. S. W. R. 1.4(+0.04/GHz)

Characteristic impedance 50 Ohms

Dielectric withstanding

voltage ≥ 1000 V.R.M.S. at 50Hz

Insulation resistance ≥ 5000 M Ohms at 500 VDC

Contact resistance ≤ 5m Ohms

Shell resistance ≤ 1m Ohm

(electrical grounding)

Climatic Data

Operating temperature -55˚C + 155˚C

(with peaks up to 180˚C)

Damp heat 56 days (40˚C - 95% HR)

Salt spray 48 hours

Mechanical data

Shells With or without dimples

Contact retention force in dielectric material > 40N

Maximum mating and unmating force

With dimples E size = 70 N

A size = 80 N

B size = 100 N

C size = 150 N

D size = 180 N

Without dimples E size = 30 N

A size = 50 N

B size = 80 N

C size = 120 N

D size = 160 N

Compatible with process

IR - Air convectioned 260˚ for 20 s.

Resistance to solder iron heat 260˚C for 30 s.

Mating cycles ≥ 200 (classe ll) or 500 (classe l)

Blind mating system Available upon request

Polarization Available with locking accessories

Consult factory

Summary of content (12 pages)

PAGE 1
TW Materials and platings Shells Steel-Tin plating Insulators High temperature black thermoplastic Signal contacts Female: machined bronze Material Male: machined brass Plating finish 16µ “Au over 79µ” Ni min. Or 30µ” Au over 79µ” Ni min.
PAGE 2
TECHNICAL DATA Shell and contacts plating CLASS ll CLASS l 0.4µm (16µ”) Au contacts gold plating 200 mating cycles 0.76µm (30µ”) Au contacts gold plating 500 mating cycles Types 77 TW 717 TW Shells and plating Tin plated shell *Male and female Tin plated shell with dimples Male only Types 177 TW 777 TW Shells and plating Tin plated shell *Male and female Tin plated shell with dimples Male only Housing arrangements Male front view Arrangement ...... Shell size ............
PAGE 3
F 1.5 10˚ H A B B’ 0.9 J D’ D E G ø 3.1 Shell size Contact P: Pin S: Socket S P A S P B S P C S P D B 0/-0.20 (0/-.008) B‘ +0.20/0 (+.008/0) C D ±0.10 (±.004) 0/-0.25 (0/-.010) 16.8 (.661”) 25.0 30.7 (.984”) 8.0 (1.209”) 16.4 (.315”) (.646”) 25.1 (.988”) 33.3 39.0 (1.311”) 8.0 (1.535”) 24.8 (.315”) (.976”) 38.8 (1.528”) 47.0 52.9 (1.850”) 8.0 (2.083”) 38.5 (.315”) (1.513”) 55.3 (2.177”) 63.5 69.2 (2.500”) 8.0 (2.724”) 54.9 (.315”) (2.161”) 52.7 (2.075”) 61.1 66.8 (2.406”) 10.9 (2.
PAGE 4
TECHNICAL DATA Straight connector footprint 1 2 A 3 A B A B B Signal tail 0.6 mm Dia. (.0236”) 1.6 mm (.063”)PCB For other PCB thickness: consult factory. Dimensions Description Power (.126” tail dia.) 1 Power (.0787” tail dia.) 1 Shielded 3 Signal 2 a 4.80 mm (.198”) 4.80 mm (.198”) 4.00 mm (.157”) 5.00 mm (.196”) b 7.2 mm (.283”) 7.2 mm (.283”) 7.2 mm (.283”) 11.50 mm (.
PAGE 5
1 2 B C 3 B C B C A A Signal tail 0.6 mm Dia. (.0236”) 1.6 mm (.063”) PCB For other PCB thickness: consult factory. Description TECHNICAL DATA Right angle connector footprint A Europe HE 5 pattern = - Europ. height - Europ. footprint pitch between 2 rows: .100” Mix Mixed pattern = - MIL height - Europ. footprint pitch between 2 rows: .100” a b c a - - - b MIL MIL pattern = - MIL height - MIL footprint pitch between 2 rows: .112” c a b c 10.30mm 6.30mm 10.00mm 10.30mm 6.30mm 10.
PAGE 6
Right angle version Connectors come equiped with metal brackets BLANK: 3.10mm (.122”) dia mounting hole RM6: metal brackets + boardlock Metal bracket RM6 Straight version BLANK: 3.10mm (.122”) dia mounting hole RM54: RM5 4.40 threaded RM53: RM5 M3 threaded 1.5 max. (.059 max.) 7.2 (.283) RM5 RM8 RM84: RM8 4.40 threaded RM83: RM8 M3 threaded A514: blind mating system FM: float mounting system ø2.2 (.086) 3.6 max. (.141 max.) + 0.25 3.5 (.137) 19.9 (.783) ø2.25 (.088) ø3 0 (.
PAGE 7
TECHNICAL DATA 4.80 (.189”) 5.20 (.205”) 5.20 (.205”) 4.80 (.189”) High power contacts 22 (.866”) øA 22 (.866”) øA øB P/N Plug øB 16 (.622”) Solder cup version Current Socket Dimensions A mm (inch) B mm (inch) L 17DM 53745-8 L 17DM 53744-7 10 to 20 Amp. 1.80 (.071”) 2.55 (.100”) L 17DM 53745-7 L 17DM 53744-6 20 to 30 Amp. 2.80 (.110”) 3.70 (.145”) L 17DM 53745-1 L 17DM 53744-1 30 to 40 Amp. 4.80 (.189”) 5.60 (.220”) Trim dimensions: 7.5 mm (.
PAGE 8
TECHNICAL DATA Straight shielded contacts Crimp ferrule and inner solder A B øD B øD F Type P/N plug plug plug plug socket socket socket socket L17DM 53740 L17DM 53740-1 L17DM 53740-3 L17DM 53740-5 L17DM 53742 L17DM 53742-1 L17DM 53742-3 L17DM 53742-5 Cable - RG Dimensions (inch) D B A Max 178 B/U 18.8 (740”) 23.6 (.929”) 1.0 (.039”) 18.8 (740”) 23.6 (.929”) 1.7 (.066”) 179 B/U 316 B/U 180 B/U 21.5 (846”) 23.6 (.929”) 2.8 (.110”) 58 C/U 21.5 (846”) 23.6 (.929”) 3.2 (.126”) 178 B/U 18.8 (740”) 23.
PAGE 9
TECHNICAL DATA Right angled shielded contact Crimp ferrule and inner solder A F E G A Type P/N plug plug plug plug socket socket socket socket L17DM 53741 L17DM 53741-1 L17DM 53741-3 L17DM 53741-4 L17DM 53743-2 L17DM 53743-3 L17DM 53743-5 L17DM 53743-6 Cable - RG Dimensions (inch) Trim dimensions (inch) G F E D B A Max 9.5 (.374”) 5.9 (.232”) 1.6 (.062”) 13.5 (.531”) 18.6 (.732”) 1.0 (.039”) 178 B/U 13.5 (.531”) 18.6 (.732”) 1.7 (.066”) 179 B/U 316 B/U 9.5 (.374”) 5.9 (.232”) 1.6 (.062”) 10.7 (.
PAGE 10
ASSEMBLY INSTRUCTIONS Cabling instructions for shielded contacts Straight crimp shielded contacts: inner solder contact outer crimp contact soft solder outer ring coaxial shell outer ring braided shield crimp 3.20 inner sleeve Right angle crimp shielded contacts: inner solder contact outer crimp contact inner sleeve coaxial shell outer ring outer ring soft solder crimp 3.
PAGE 11
... TW ... ... ... ... ... ... RoHS Compliant Contacts and Shell Contact Plating 0.4µm(16µ”) Au 0.
PAGE 12
Amphenol IT & Communication Products Block A3/A4, The 4th Industrial District of Industrial Headquarters, Dong Keng Road Gong Ming Town, Shen Zhen China Fax:+86(0)755 2754 9955 Technical Support Tel:+86(0)755 2717 7945 Info-dsub@amphenol.com.cn http://www.dsubconnector.com The information given in this document are as a guideline only. We reserve the right to modify our products in any way we deem necessary. Any duplication is prohibited, unless approved in writing.