Brochure

ManualsBrandsAmphenol Industrial ManualsConnectorsSealing plug

INTERCONNECTINGYOURWORLD

Plug Assembly

Contact and Wedge Insertion

5. A ‘click’ will be felt when the wedge is

fully installed.

1. Grasp crimped contact approx. one

inch behind the contact barrel.

1. Remove wedge by inserting a ﬂ athead

screwdriver head underneath the lip

of the wedge.

2. Twist the ﬂ athead screwdriver until

wedge ‘pops’ out of connector.

3. Use the same ﬂ athead screwdriver to

remove contact inside connector.

2. Hold connector with rear grommet

facing you.

3. Push contact straight into connector

until a ‘click’ is felt. A slight tug will

conﬁ rm placement.

4. Insert wedge into connector.

Contact and Wedge Removal

What are AT Series

™

Connectors?

Amphenol Sine Systems AT Series

™

connectors were designed as a high-performance, cost-effective solution

to be used within the Heavy Equipment, Agricultural, Automotive, Military, Alternative Energy and other

demanding interconnect architectures. The AT Series

™

connectors contain superior environmental seals,

seal retention capabilities and feature Amphenol Sine Systems RockSolid

™

Contact technology. In addition,

all of our AT Series

™

connectors have been developed to be completely compatible with all other existing

standard products industry-wide.

Longer contact life

Lower contact resistence

Immunity to shock and vibration

Low insertion and extraction forces

Contact area extends 360° around pins

•

Hyperbolic Contacts

- Optional

WEDGE with Added Seal Retention

The added seal retention feature

ensures that the Front Seal does not

move out of place.

FRONT SEAL

The superior design ensures a tight

environmental seal when used

in conjunction with the recessed

cavity of the connector body.

RECESSED SEALING AREA

The recessed cavity allows

for a secure ﬁ tting

front seal.

ERGONOMICALLY DESIGNED CLIP

The increased size and tactile design

of our clips allow for easier mating

and unmating.

SEALING PLUGS

- Optional

Back Cap

- Optional

Rear Seal

- Also available in Reduced Diameter or Solid

Summary of content (10 pages)

PAGE 1
1 What are AT Series™ Connectors? Contact and Wedge Insertion Amphenol Sine Systems AT Series™ connectors were designed as a high-performance, cost-effective solution to be used within the Heavy Equipment, Agricultural, Automotive, Military, Alternative Energy and other demanding interconnect architectures. The AT Series™ connectors contain superior environmental seals, seal retention capabilities and feature Amphenol Sine Systems RockSolid™ Contact technology.
PAGE 2
1 10 AT Series™ Connectors Pin Contacts, Socket Contacts and Tooling • The connector design incorporates an integral latching system that ensures a definitive electrical and mechanical connection Listed below are quick-reference illustrations for RockSolid™ and stamped and formed crimp options, as well as the Amphenol Sine Systems part numbers.
PAGE 3
9 2 All measurements in Inches Listed below are quick-reference illustrations for both Military-style and DiagnosticGrade™ crimp options, as well as the Amphenol Sine Systems part numbers. Military-Style Solid Crimp A B C D PIN CONTACT C Size/ Type A Max B Min C Max D Min Wire Gauge Range Recomm’d Strip Length AT60-202-1631 (Gold) AT60-202-16141 (Nickel) 16 PIN .821 .066 .103 .250 16 and 18 .250-.312 AT62-201-1631 (Gold) AT62-201-16141 (Nickel) 16 SOC .759 .066 .103 .
PAGE 4
3 8 AT Series™ Receptacles, Plugs and Wedges - 8 (A-D) Position AHD Series™ 9 Pin Receptacles and Plugs (J1939) Note: The views shown below are Mating Face Views WEDGES PLUGS WEDGES RECEPTACLE - Military Style SMOOTH SHELL PLUG - DiagnosticGrade™ P/N: AT04-08PA P/N: AW8P P/N: AT06-08SA P/N: AW8S P/N: AHD10-9-1939P P/N: AHD17-9-1939S (available w/out Rear Seal) LOCKING RING PLUG - Military Style LOCKING RING PLUG (Non J1939) - Military Style P/N: AHD16-9-1939S P/N: AHD16-9-96S 1 8 POSITI
PAGE 5
7 4 AHD Series™ 6 Pin Receptacles, Plugs and Caps AT Series™ Receptacles, Plugs and Wedges - 12 (A-D) Position Note: The views shown below are Mating Face Views The AHD Series™ products listed below provide a quick connection between Amphenol Sine Systems 6 Pin products and equivalent industry 6 Pin products.
PAGE 6
5 6 AT Series™ Plugs, Wedges and Connectors - 12 and 18 Position All measurements in Inches PLUG WEDGE PLUG WEDGE P/N: AT06-12SX1 P/N: AW12S P/N: AT06-12SX2 P/N: AW12S 12 POSITION (X2) 12 POSITION (X1) Note: The views shown below are Mating Face Views 1 PLUG (Fully assembled. Amphenol Sine Systems AHD Series™ Connectors were developed in response to the overwhelming need for an economic alternative to today’s existing diagnostic product options.
PAGE 7
9 2 All measurements in Inches Listed below are quick-reference illustrations for both Military-style and DiagnosticGrade™ crimp options, as well as the Amphenol Sine Systems part numbers. Military-Style Solid Crimp A B C D PIN CONTACT C Size/ Type A Max B Min C Max D Min Wire Gauge Range Recomm’d Strip Length AT60-202-1631 (Gold) AT60-202-16141 (Nickel) 16 PIN .821 .066 .103 .250 16 and 18 .250-.312 AT62-201-1631 (Gold) AT62-201-16141 (Nickel) 16 SOC .759 .066 .103 .
PAGE 8
1 10 AT Series™ Connectors Pin Contacts, Socket Contacts and Tooling • The connector design incorporates an integral latching system that ensures a definitive electrical and mechanical connection Listed below are quick-reference illustrations for RockSolid™ and stamped and formed crimp options, as well as the Amphenol Sine Systems part numbers.
PAGE 9
11 What are AT Series™ Connectors? Contact and Wedge Insertion Amphenol Sine Systems AT Series™ connectors were designed as a high-performance, cost-effective solution to be used within the Heavy Equipment, Agricultural, Automotive, Military, Alternative Energy and other demanding interconnect architectures. The AT Series™ connectors contain superior environmental seals, seal retention capabilities and feature Amphenol Sine Systems RockSolid™ Contact technology.
PAGE 10
12 We are Amphenol , a GLOBAL LEADER in providing YOU with Contact and Wedge Insertion 1. Grasp crimped contact approx. one inch behind the contact barrel. 2. Hold connector with rear grommet facing you. 4. Insert wedge into receptacle. 5. A ‘click’ will be felt when the wedge is fully installed. 3. Push contact straight into receptacle until a ‘click’ is felt. A slight tug will confi rm placement. INTERCONNECT OPTIONS and SOLUTIONS.