Datasheet

48
F
F
R
B
CUT-OUT FOR
PT ONLY
PIN LOCATION FOR PC ONLY SECTION
JAM NUT MOUNTINGS
FLANGE MOUNTED CONNECTORS
All ange mounting PT connectors use standard MS mounting
dimensions. They cannot be back panel mounted due to
coupling clearance. The PTB (thru-bulkhead) type con nector
must also be back panel mounted on one side. Flange gaskets
are available for both series, see page 37.
Shell
Size
R
(TP)
D
Dia.
PT SP PT SP
6 .469 .641 .323 .439
8 .594 .734 .449 .563
10 .719 .812 .573 .680
12 .812 .938 .699 .859
14 .906 1.031 .823 .984
16 .969 1.125 .949 1.108
18 1.062 1.203 1.073 1.233
20 1.156 1.297 1.199 1.358
22 1.250 1.375 1.323 1.483
24 1.375 – 1.449 –
JAM NUT MOUNTINGS
The jam nut design has become very popular because it allows
bench wiring of harness assemblies. The labor saving often
off sets the added cost of the jam nut receptacle which is due to
the self contained “O” ring and the extra nut.
Shell
Size
R
+.010
–.000
B
+.000
–.010
F
±.010
P
Panel Thickness
Min. Max.
6 .447 .420 .286 .062 .125
8 .572 .542 .331 .062 .125
10 .697 .669 .375 .062 .125
12 .884 .830 .442 .062 .125
14 1.007 .955 .486 .062 .125
16 1.134 1.084 .530 .062 .125
18 1.259 1.208 .573 .062 .125
20 1.384 1.333 .641 .062 .250
22 1.507 1.459 .685 .062 .250
24 1.634 1.575 – .062 .250
HERMETIC RECEPTACLE MOUNTINGS
This series must be mounted in such a way as to preserve the
hermetic seal provided by the glass insert. Mounting data for
box and jam nut receptacles is given above. Cut-out required
for solder mounting receptacles (N) is given below.
Shell
Size
N
Max.
6 .458
8 .582
10 .692
12 .801
14 .926
16 1.051
18 1.176
20 1.395
22 1.375
24 1.520
The nish of each of these hermetic
receptacles is fused electro-deposited
tin for easy solderability, and protected
by a special lacquer for optimum shelf
life. The lacquer will not interfere with
any soldering operation.
Low temperature solder should be used
and the addition of a solder llet at arrow
points on drawing at right is rec-
ommended. Care must be taken that the
operating temperature of the nal
assembly does not rise above the
melt ing point of tin (440° F).
Mounting Recommendations
for miniature cylindrical connectors
N
CUT-OUT
SOLDER
RECEPTACLE
JAM NUT
RECEPTACLE
(See dimensions
above)
BOX
RECEPTACLE
(See dimensions
above)
HERMETIC RECEPTACLES
R
(TP)
R
2
D Dia.
R
2
.120 Dia. for Shell Sizes 6-22
PC & PT
.147 Dia. for
Size 24 PT
.150 Dia. for
SP only
4 HOLES
CUT-OUT
SECTION
No. 4 Screw
for PC & PT
No. 6 Screw
for SP and for
Size 24 PT
FLANGE MOUNTED CONNECTORS
4 HOLES
.120 Dia. for Shell Sizes 6-22 PT
.147 Dia. for
Size 24 PT
.150 Dia. for
SP only
No. 4 Screw
for PT
No. 6 Screw
for SP and
Size 24 PT
F
F
R
B
CUT-OUT FOR
PT ONLY
PIN LOCATION FOR PC ONLY SECTION
JAM NUT MOUNTINGS
PT PANEL CUT OUT